Search Documents

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By M. A. N. Rosa, L. C. R. Machado, R. A. Fonseca, A. M. Mendonça

"Sossego Mine was the first Vale SAG mill operation to process copper-gold ore. It is located in the state of Para, in the south-eastern Amazon region of Brazil. In the first six years of continuous operation, Vale investigated different alternatives for improving circuit performance by investigating operating conditions, mainly focusing on the SAG mill.Today, after a steady increase over five years the annual production rate seems to have stabilized. It is hoped this work will show how the SAG operating practice have been perfected with time and as new data are collected. Historical data of mill grind-outs and crash stops helped create operation curves depending on the ball charge volume and total charge volume. Also noted were impacts on throughput due to the effect of reducing liner weight and the ore type characteristics."

Jan 1, 2012

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By Dina Aloi

The need to be seen as responsible neighbours and good corporate citizens is a critical success criteria for mining companies. To be seen as responsible requires both achieving responsible performance, and making that good performance visible to the community, legislators, investors, and other stakeholders. This has broadened the skills required for the successful operation of a mining company to include social sciences, public affairs, communications, and environmental sciences. Mining companies still look to technical specialists to achieve the core of that good performance - broadly characterized as a sustainable operation. However, the degree of understanding that those specialists have of the requirements for sustainability and overall Corporate Social Responsibility has a tremendous impact on the overall performance of the project and company. In her keynote address to the Sustainability for Profit session, Dina will outline some of the key areas in which technical employees and consultants can contribute to achieving successful sustainable mining operations.

Jan 1, 2010

By Masaru Kato

The plated gold being used by the electronics industry can be broadly classified into two categories: soft gold and hard gold. Soft gold is used for circuit metallization and for bonding semiconductor chips, while hard gold is indispensable as the contact material on electrical connectors, electromechanical relays, and printed circuit boards. The traditional baths from which to plate soft gold as well as hard gold contain the cyanide complex, [Au(CN)2]-, as the source of gold, which liberates free cyanide ions during the plating. The free cyanide is not only highly toxic but also attacks photoresists used to delineate circuit patterns and bonding pads. For these reasons, non-cyanide baths are in use to plate soft gold, whereas hard gold can be plated only from cyanide baths at present. In this presentation, the current status of both electrolytic and electroless non-cyanide processes for plating soft gold will be reviewed.

Oct 1, 2003

By B. Huffman

This paper examines several new trends in the design and application of linings for copper melting shaft furnaces including the use of large shapes, monolithic back-up linings and improved refractory engineering to significantly reduce refractory installation time, diamond saw blade costs, fuel and down-time. The net results are shown to be dramatically increased refractory service life, reusable safety linings, elimination of hot spots and lower refractory disposal costs.

Jan 1, 2007

By Kathy Pomeroy

Sharing?? l Maybe not the first image that comes to mind when we think about the historical corporate mind set and track record of many corporations ? ! A Fundamental Change in Relationships l From a worldview of independence to one of recognized interdependence l Collaborative action with communities for long range mutual goals l Acceptance of greater accountability for the whole l Community and government relationships based on trust, mutuality, respect for human rights, equity, sustainable agreements

May 1, 2002

By W. Qin

The nucleation of d hydride in Zircaloy-4 has been studied using electron backscatter diffraction. Hydrides prefer to nucleate at intergranular rather than intragranular sites. (0001) a -Zr//(111) d -ZrHx is the most common crystallographic relationship. The hydride platelets are generally interlinked each other and form a chain-like configuration. Based on thermodynamic model, the formation mechanisms of the hydrides at different sites and the interlinked structure were analyzed. We found that the misorientation of two adjacent grains has a crucial effect on hydride nucleation sites, and the tensile stress near the tips of hydride platelets is a key factor affecting the appearance of interlinked structure.

Aug 1, 2010

By Adrian White

Agenda Overview of pastefill at Kidd Mine Pipeline wear and the need to monitor Steel Loop monitoring Steel Borehole monitoring Monitoring pipe linings

May 1, 2013

CFD (Computational Fluid Dynamic) models have been developed and validated for a pulsed column with disk-doughnut internals, as used for solvent extraction. First a single phase model was developed to simulate the turbulent oscillating flow around the internals of the column. This model was successfully validated using detailed PIV measurements of velocity taken at eight different phases through the pulse cycle. Second, the CFD model was extended to allow for a continuous aqueous phase and a dispersed organic phase (kerosene) flowing counter-currently. The model was a two-fluid model that accounts for droplet breakup and coalescence, and solves for droplet size distribution using a population balance model incorporated into the CFX4 package. PDIA (Particle Droplet Image Analysis) measurements were taken on a pilot scale solvent extraction pulsed column to determine droplet size distribution for calibration and validation of the CFD model. The measurements were made under pulsing intensities ranging from 10 mm/s to 32.5 mm/s.

Jan 1, 2007

By Hang Zhao, Xinping Li, Pingan Wu, Yi Luo

The deep-buried rock surrounding the Jinping II Hydro-power Station was taken as the engineering background. Using model specimens of classified rock materials to simulate fractured rock mass under high in-situ stress conditions, the test about acoustic propagation law on single fracture model of specimen under different pressures and different angles were carried out. The variation of p-wave velocity in fractured rock mass and axial stress-strain relationship in the whole test procedure was also studied. Based on damage mechanics principle and the acoustic wave propagation in cracked rock mass, comparative study on damage constitutive relation of fractured rock mass under high in-situ stress in consideration of equivalent strain and equivalent energy was performed. As the results showed, with the change of axial stress level under constant confining pressure, the change in wave velocity can be divided into three stages: slow increase (small variation in amplitude), rapid reduce (large variation in amplitude ) and accelerate reduction. When the confining pressure is constant, the maximum p-wave velocity and the peak strength of specimens increases with the decrease of the crack angle. When the crack angle is constant, the maximum p-wave velocity and the peak strength of specimens increases with the increase of confining pressure.It is identified that the theoretical calculation results of constitutive relation about elasto-plastic damage model containing variable wave velocity in the fractured rock mass is consistent with the model test results.Therefore,the constitutive relation can provide reasonable suggestions for engineering practice.

Jan 1, 2015

By Wencheng Gao

An attractive way to beneficiate magnesium chloride and aluminum chloride is to prepare Mg-Al spinel, an excellent refractory material. Mg4Al2(OH)14?3H2O, the precursor of spinel, can be prepared using a co-precipitate method from aqueous MgCl2-AlCl3 solutions. The co-precipitation process of magnesium-aluminum from acidified chloride solutions by using NaOH or NH4OH as base neutralization agent was studied. Co-precipitation was conducted from different mixed solutions ? at initial CAl=0.0625M and Mg/Al molar ratio from 0.5 to 10, the temperature range from 30 to 90 °C. The effect of other parameters, including base type, method of base addition, base addition rate, aging time, background electrolyte and concentration were also investigated. The co-precipitation process was monitored by potentionmetric(pH) measurements. The experimental pH curves were characterized by two platforms separated by a steep jump in pH at Mg/Al molar ratio 0.5~6. The first platform was centered at about a pH of 3.8 and the pH of second platform was varied with different conditions. When the Mg/Al molar ratio was up to 6~10, the first platform in pH was almost disappeared. Furthermore, the shapes of pH curves were also affected by base type, base addition rate and method of base addition. Experimental results showed that the first platform in pH was connected with Al precipitation, and the second platform was involved with Mg. The final co-precipitates were characterized by XRD, TGA-DTA, particle size analysis, SEM and TEM. We found both Mg/Al molar ratio and temperature proved to be the key parameters controlling the formation of Mg4Al2(OH)14?3H2O phase. At solution Mg/Al ratio=0.5~4, the main precipitate phase was Bayerite (Al(OH)3) admixed with Mg4Al2(OH)14?3H2O; at Mg/Al ratio=4~6, the main phase was Mg4Al2(OH)14?3H2O admixed with some Mg(OH)2; while from Mg/Al ratio=6~10, the systems were mixtures of Mg(OH)2 and Mg4Al2(OH)14?3H2O.

Oct 1, 2011

By Y. M. Shneerson, I. V. Fomenko, M. A. Pleshkov, E. A. Ospanov, A. A. Shakhalov, S. S. Naboychenko

Low-grade copper concentrates (with copper content less than 20%) often contain impurities such as arsenic, zinc, lead, mercury, antimony and bismuth. The pyrometallurgical treatment of such concentrates is associated with several problems, which will ultimately affect the cost and the quality of copper cathodes as well as by-products. SRC Hydrometallurgy proposed a complex hydrometallurgical technology which allows the removal of impurities and the enrichment of low-grade copper concentrates to a quality which will be more suitable for pyrometallurgical processing. Laboratory batch tests and pilot plant results for the pressure leaching steps are shown in this paper. The key parameters of the leaching steps were determined and optimized. The quality of possible by-products were also determined. The developed flowsheet includes two pressure leaching steps: pressure oxidation (POX) and hydrothermal alteration (HTA). Both operations are carried out at 170°C with subsequent flotation of POX and HTA residues and recovery of copper, zinc and lead into separate concentrates for further processing. The development of the flowsheet was based on the Balkhash Zinc Plant (Balkhash, Kazakhstan), which had been non-operational since 2009. The developed flowsheet for processing of low-grade concentrates will utilize 80% of the existing equipment of the Balkhash Zinc Plant, thus leading to a significant reduction in required capital expenditure. INTRODUCTION As the age of copper mining operations advance, copper grades continue to diminish and impurity levels increase. Therefore, copper producers are forced to look for new innovative hydrometallurgical technologies which are able to handle low-grade raw materials and solve problems associated with impurities in an economically justifiable way. New technologies allow to extract valuable components selectively and to process low-grade concentrates which had previously been marked as non-technological and economically unviable. Hydrometallurgical technologies for processing of copper-containing materials can be divided into two main categories: chloride and sulfate (atmospheric, autoclave and bacterial) based technologies. Since the 1970s, many autoclave techniques for the processing of copper-containing materials have been developed and implemented (Naboichenko, 2002; Dreisinger, 2005; Habashi, 2009; Shneerson, 2011). The mineralogical composition of the ore (or concentrates), geographical location of the deposit, distance from industrial areas, availability of existing treatment facilities, availability of skilled labor, cost of electricity and cost of neutralization are some of the factors which are usually considered when the appropriate technology is selected (Halbe, 2002).

Jan 1, 2019

"In conjunction with Banick Mercur , Wright Engineers Limited designed the first multi-stage aqueous pressure oxidation system in an alkaline environment in North America. A three-stage slurry heating and slurry pressure let-down with heat recovery was an innovative approach to the problem of high energy cost with the low sulphur content of the ore. The design of this system required solving a number of problems associated with heating and pumping of slurries at pressures up to 3230 kPa and temperatures in excess of 220°C. Wright received an Award of Merit in October 1989, from the Canadian Consulting Engineering Awards Committee in the Process Category for its design of the Mercur pressure oxidation system.The Mercur Mine is located at the south end of the Oquirrh Mountains in Tooele County about 65 miles by road from Salt Lake City, Utah, U.S.A. The original mill was designed to process 5000 tpd of oxidized gold ore in a carbon-in-leach (CIL) circuit. A new ore treatment system was required to treat the substantial quantities of refractory ore reserves which could not be treated economically in the existing mill. The new pressure oxidation circuit makes the refractory ore amenable to gold recovery by oxidation of the sulphides contained in the ore .Wright Engineers Limited was commissioned by Barrick Mercur Gold Mine Ltd ., a wholly-owned subsidiary of American Barrick Resources, to design the pressure oxidation facility. This followed completion of a feasibility study by Wright which showed that the project was technically and economically viable.Work on the feasibility study began in 1986, detail design commenced in February 1987, and was completed in December 1987. Mechanical installation was completed in January 1988, and slurry feed began in February 1988. The plant has operated since June 1988 without major interruption . Wright was responsible for engineering, procurement and construction management for the addition of the 750 tpd pressure oxidation circuit to the existing mill and also had commissioning responsibility.Major unit processes involved in the pressure oxidation facility are ore thickening, three-stage slurry preheating, pressure oxidation and three-stage slurry cooling with heat recovery, stearn generation, propane and oxygen storage and a video graphic display process control system were included in the scope as process anciliaries.The pressure oxidation increases gold recovery from the refractory ore by conventional CIL from as low as 35% to more than 86070. A patent has been granted for the process."

Jan 1, 1989

By G. Kordosky

The experience of one plant regarding degradation of copper solvent extraction reagents in the presence of 20 to 30 g/1 nitrate in the leach solution was described at Cobre 2003. However, little information is available about the degradation of copper solvent extraction reagents where the nitrate concentration of leach solution is much lower. Analysis of plant organic samples taken from an operating copper SX plant over a long period of time shows that small amounts of nitrate in the leach liquor can be a significant contributor to reagent degradation provided certain other conditions are present. These conditions are discussed and cautionary suggestions on copper SX plant operations in the presence of even low levels of nitrate in the pregnant leach are made based on industry experience with copper solvent extraction plants and copper solvent extraction reagents.

Jan 1, 2007

By M. Okada

Consumption of refined copper in Asia, especially in China and India, has soared, and the copper price is at its historic height. New smelters and refineries have been built in the region with state-of-the-art technology to meet the unprecedented demands. Supply of copper concentrate, on the other hand, has fallen short of the growing demand for concentrate by the smelters and refineries with expanded production capacities. The shortage of copper concentrate is attributable to the delay in the mining development, caused by the prolonged price slump of before 2005. The mismatch between supply of concentrate and smelting and refining capacities may cause disorderly movement of copper price, and hamper the sound development of the industry. The recent high copper price may prompt substitution with alternate materials. With electrical and thermal conductivity and workability, copper is one of the most customer-friendly materials. It is regrettable for both customers and suppliers if the high copper price would become an impediment to promoting copper use. Some outdated and environmentally unfriendly facilities still operate. In view of recent lower-grade copper concentrate with higher sulfur content, these facilities must reform their equipment to environmental-responsive one. The current level of per capita consumption of refined copper in Asia shows that the demand of copper will further grow. It is necessary to realize stable supply of refined copper and stable copper price, to help developing countries including China and India to economically take off. Hence, it is essential that the development of the copper industry be accompanied by environmentally friendly facilities, and harmoniously increased capacities between mining and smelting and refining.

Jan 1, 2007

By Michel Jebrak, Claude Bellehumeur

Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not dermed by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis. The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By C. Denis Thibodeau

Outline Introduction 402 OB Mining Sequence Trial to Verify Sequence Change Monitoring Observations Numerical Modelling Conclusion

May 1, 2013

By P. C. Holloway, M. J. Collins, K. R. Buban

Historically, there has been little incentive to process copper-arsenic concentrates by leaching, rather than via established smelting operations. However, with ever tightening environmental emission standards and more arseniferous concentrates being produced, increasingly sophisticated and upgraded off- gas handling facilities are required in smelting operations, generating greater quantities of challenging metallurgical dust. In this context, oxidative pressure leaching offers distinct advantages. The current state of pressure leach technology delivers high extractions from copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. However, as was shown in an earlier study, copper extractions and environmental leach residue stability are impacted negatively by arsenic levels above 2.5 to 3.0 wt%. In further studies on pressure leaching of copper concentrates, Sherritt has developed process conditions that allow even highly arseniferous (> 7 wt% As) feed materials to be converted into environmentally stable residues, with excellent copper extractions. At the same time, pressure leach residues can be generated that are amenable to silver recovery via direct cyanidation, without pre-treatment by lime boiling or hot curing. The results of pilot plant test work are discussed. INTRODUCTION As the production of copper has expanded over the years, resource exploitation has extended beyond relatively clean, high grade and easily accessible ores, and copper sulphide concentrates increasingly come with higher levels of contaminants, such as As, Hg, Sb and Bi, and lower copper and sulphide sulphur concentrations. However, as concerns on the impact of the emission of such contaminants into the natural environment have mounted, import/export restrictions have made the trading of copper concentrate more difficult, and, in particular, the export of concentrates with greater than 0.5 wt% As; under ever tightening environmental emission standards, these lower quality concentrates can be a significant strain on the off-gas handling facilities in smelting operations. The processing of arsenic bearing copper concentrates is, therefore, an increasing challenge as copper producers seek to exploit more complex mineralization and to extend the life of their operations. In this environment, processing arsenical copper concentrates with high temperature pressure leaching (>200°C) must be considered as an alternative to pyrometallurgical processing. Leaching kinetics for copper minerals at these temperatures are rapid and acid is generated for potential use in heap leach operations. Pressure leaching of copper concentrates eliminates gaseous emissions of arsenic and sulphur, while generating environmentally stable residues, as measured by the Toxicity Characteristic Leach Procedure (TCLP) (Kalanchey et al., 2007). Both medium and high temperature pressure leaching of copper concentrates have also proven themselves technically on an industrial scale (Marsden et al., 2004) with high copper recoveries.

Jan 1, 2019