Search Documents

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By T. H. North, A. G. Glover, R. J. Pick

"Girth welding operations represent the rate-limiting step in pipeline construction. A joint industry-university program was set up to establish the field welding characteristics of large-diameter, high-strength line pipe.Theoretical work carried out at the University of Waterloo showed that pipe wall thickness and joint misalignment prior to welding has a marked influence on the lifting stresses acting on the root pass of girth welds. Pipe diameter and pipe ovality had negligible effects. Super-position of lifting and residual stress (caused by the fusion welding operation) highlighted regions of the weld bead most susceptible to hydrogen-induced cracking.The field welding characteristics of 1219-mm-diameter, 13.72-mm-wt Grade 483 line pipe were evaluated using a specially designed test rig. The principal test variables were lift height, delay time after root pass deposition, preheat temperature, pipe composition and joint misalignment prior to welding. For any given life, preheat and joint misalignment prior to welding had the most significant effect on cracking tendency.The output of this program has industrial significance and illustrates the beneficial features of university-industry collaboration.IntroductionField welding operations comprise the rate-limiting step during pipeline construction. Crack-free girth welds must be made in a wide range of weather conditions and consequently the field weldability of line pipe compositions directly affects pipeline integrity and construction economics.Pipe-laying practice comprises root bead deposition followed by a skidding operation involving lifting (or lowering) the pipe length onto skid s so that the next pipe length can be aligned prior to welding. Consider pipeline construction using 24.4-m lengths of 1219-mm-diameter , 13.72-mm-wt Grade 483 pipe weighing approximately 10,000 kg. Skidding involves loading a 3-mm-thick root bead by moving the free end of the pipe through vertical distances of up to 700 mm . The likelihood of cracking in these circumstances depends on the inherent crack susceptibility of the pipe composition employed, on the hydrogen content of the deposited weld metal and on how well the joint handles the external stressing caused byskidding."

Jan 1, 1981

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By J. W. Markham, M. Atiemo, K. Yoshida

INTRODUCTION In open-pit mining of high grade ores, operators of mining equipment in a pressurized cab are protected from inhaling radioactive aerosols by the use of filtered air through a pre-impactor and a HEPA (high efficiency particulate air) filter. At present, a limited amount of scientific information is available on the worker exposure to airborne alpha emitters in the mining of high-grade ores. (Miller, 1977, Nielson, et al, 1979). Factors affecting the worker exposure to alpha radiation are: the grade of uranium containing ores, the environmental conditions inside the mine pit, the protection factor of the cab filter system, the workers' attitude towards the hazards of radioactivity and the adopted contamination control in the cabs. Four series of field samplings were conducted during the fall of 1980 and the summer of 1981 at a mining site in northern Saskatchewan to investigate the extent of protection an equipment operator has against cab internal exposure to airborne alpha emitters with short and long half-life radionuclides. The variation in the breathing zone concentrationnof aerosols as a result of resuspension is discussed, however no attempt was made to isolate and investigate the factors and the associated parameters of the aerosol resuspension phenomenon. AEROSOL RESUSPENSION IN A CAB Mechanisms of Resuspension [Sources]: The presence of radioactive aerosols inside a cab and in the breathing zone of an operator may be due to initial concentration inside [(CO)], concentration in the filtered (HEPA) air (CC, at the flow rate [QC]), the concentration of the aerosol through resuspension ([CR]), the aerosol concentration in the air outside the cab ([CE]) and the concentration of the aerosol in the leaking air [(CL)], at the flow rate of [(QL)]. [Volumetric Equilibrium]: Assuming a uniform concentration of the aerosol in the cab, the aerosol concentration in the breathing zone[ (CBZ)] may be expressed as, [CBZ+CO+CC+CR-CL] If [QC] remains greater than [QL], there is pressurization in the cab. There is particle loss as a result of the leaking air from the tight cab, however the condition of adequate pressurization ensures that [CL ~ CC]. Also for dust particles filtered through HEPA [CC – 0] thus [CBZ + CO + CR] For the radioactive gases, [CBZ - CO + CC] Over long periods,[ CBZ – CE] but if [CBZ] exceeds the value of CE then the aerosol build-up in the cab has, occurred. [Resuspension]: Turbulent bursts are generated within the core region of a cab confinement, such that the down sweeps and the up sweeps of the air bursts cause resuspension of dust from the surfaces. Particles initiate resuspension by four major modes: namely, sliding, rocking, rolling, bouncing or sudden ejection or by combinations of these. Nevertheless the adhesion force between the particles and the surface must be overcome by ejection forces before ejection takes place (Kline et al, 1967, Corino and Bradkey 1969, Kim et al 1971). The phenomenon of particle resuspension from a surface may be expressed in a generalized form as: CR =f (Uz . R . D . H) where CR = Rate of particle resuspension UZ = Surface shear velocity R = Surface roughness parameter D = Aerodynamic diameter of particle H = Frequency of surface airburst A detailed discussion of the individual parameters was attempted for the case of farm tractor cabs by Atiemo (1981), such a treatment is out of the scope of this study. Only the effects of the properties of surface roughness will be discussed. Effect of Surface Properties The roughness of the surface from which dust particles are ejected plays a significant role in the deposition and resuspension of the dust. The roughness or the amount of protrusions greatly influence the intensity of air turbulence in the immediate vicinity of the surface (Schmel 1976). For most roughened surfaces therefore, larger particles may be dislodged in greater quantities than smaller particles. The deposition and the resuspension of dust particles from different surface materials of glass, cloth, metal and rubber have been studied in a wind tunnel (Atiemo, 1981). Field Conditions Mining equipments used are: a backhoe, a bulldozer with ripper attachment and two dumptrucks for high-grade ore operations; a payloader and two dumptrucks for waste handling; and a jumbo drill which drills dynamite holes for ore blasting. All this

Jan 1, 1981

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By Didyk M. Marko, Vásquez Ñ. Gregorio

INTRODUCTION The Salvador Division of Codelco Chile is an important copper molybdenum production center, located 1,200 km north of Santiago and 124 km east of the Pacific Ocean, in the foothills of the Andes Range. El Salvador Mine produces by block caving 8,600,000 t of ore with a content of 1 .l0% Cu and 0.02% Mo, from a copper porphyry ore body. The geology of the ore body shows a great heterogeneity as to rocks, grade distribution, ore height and undercutting levels. This has resulted in a variety of designs for the productive units (blocks) and in the mineral handling systems. Up to now, 4 systems have been employed: grizzly and intermediate haulage; slusher drifts with intermediate ore pass and haulage; slusher drifts with scraper loading directly into trains; and, LHD. On the other hand there is a marked dispersion in the final results from each block mined out. We report here the conclusions reached after analyzing the data gathered on the mining of 163 depleted blocks, representing a total production of 102,000,000 t, with an undercut area of 340,000 sq m. The final results of each block, characterized in terms of tonnage and fine cop- per recovery, were studied as a function of a number of design, geological, and operational parameters. BASIC CONCEPTS Indices of Efficiency In order to evaluate the final result of each block, or group of blocks, the following indices of efficiency were defined : Tonnage Recovery (TR) . It is the ratio between the ore tonnage extracted and the in situ tonnage estimate for each block or group of blocks. Grade efficiency (E) . It is the ratio between the Cu mill feed grade and the in situ Cu grade estimate for each block or group of blocks. Grade efficiency is numerically equal to the ratio between fine copper recovery (FR) and tonnage recovery (TR) . Figure 1 shows the final results for 163 mined out blocks, in terms of tonnage and fine copper recovery. Different grade efficiencies are also indicated. The marked dispersion in the final results of mined out blocks must be stressed since it greatly incides in mine planning. It must be kept in mind that an eventual concentration of low overall efficiency in the blocks during a given period (e.g., one year) will make it necessary to bring into production new blocks over the standard development schedule. It is worth noting that the final results in the 163 mined out blocks corresponding to a production of 102,000,000 t of ore with a mill feed grade of 1.445% were obtained from an ore estimate of 93,000,000 t and a grade of 1.671% Cu, which represents 110% tonnage recovery and 86% grade efficiency. Parameters Studied The following parameters are considered in this study: Geological Parameters. These parameters depend exclusively on the geological and geotechnical features of the ore body. IN SITU GRADE: The initial estimate of the block grade. Four copper grade categories were considered : (a) lower than 1.3% ; (b) 1.3 to 1.6%; (c) 1.6 to 2.0%; (d) higher than 2.0%. The overall initial in situ estimate of the ore body was 1.6% Cu. IN SITU TONNAGE: Initial tonnage estimate of the block. Four categories are considered: (a) below 500,000 t; (b) 500,000 to 1,000,000 t (c) 1,000,000 to 1,500,000 t; (d) over 1,500,000 t. CONTACTS SLOPE: Since up to 4 rock types can be found in a block, resulting in a corresponding number of contacts, a horizontal con- tact was defined as that which forms an angle of less than 45" with the horizontal and a vertical contact that which forms an angle of more than 45" with the horizontal. GRADE DISTRIBUTION: As in rock types, horizontal and vertical grades were defined. ORE HEIGHT: The distance measured between the undercut level and the top of ore. Four categories are considered: (a) less than 60 m; (b) 60 to 100 m; (c) 100 to 150 m; (d)over 150 m

Jan 1, 1981

Reduce costs of recontouring surface mined land by improving bulldozer blades. Approach A specialized 48-foot-wide bulldozer blade set at an angle, a 13-foot bulldozer blade with swept-forward end sections, and a 24-foot grading bar are used in conjunction with conventional bulldozers to reduce the cost of recontouring surface mined land. How They Work The angle blade is used to do the initial and intermediate leveling of long spoil banks. It is mounted at an angle on two 410-horsepower crawler tractors in a side-by-side offset configuration, but requires only one operator since both tractors are controlled by a single set of controls. The angle blade usually begins its cycle at one end of the spoil bank where the operator fills the blade and moves forward, continuously cutting and casting the material to the repose slope. At the opposite end of the spall bank, the angle blade turns around and begins cut-ting and casting material to the opposite repose slope. This action continues until adjacent banks meet or the lateral distance from the center line of the spoil bank to the repose slope exceeds approximately 40 to 50 feet. At this distance, the sidecasting angle blade is no longer effective, and conventional bulldozers are used to do the final land shaping.

Jan 1, 1981

By K. C. Watts

The Silver City mining region is located in Grant County, southwestern New Mexico (Fig. 1). This area is well known, having produced large tonnages of base and lesser amounts of precious metals over the past several years. Mining within the region continues today, as well as exploration activity, which seems to have been on the increase since the recent discovery of a large skarn-associated Zn-Pb-Cu replacement deposit near Pinos Altos, a mineral district within the region (McKnight and Fellows, 1978). Because the Silver City area contains a number of mineral districts and retains promise for additional deposits, as suggested by widespread hydrothermal alteration and favorable igneous rocks, it was selected as the focus of two independent geochemical studies, both seeking to enhance anomaly-to- background contrast in order to improve our abilities to detect blind metal deposits or subtle manifestations of near-surface occurrences. The first of these independent studies involved the systematic sampling of those secondary Fe-Mn oxides that occur within coatings, selvages, and fault fillings, and then the selective extraction of these oxides from the host-rock matrix by chemical methods. The second study sought to isolate clastic Fe-Mn-rich materials from the heavy fraction of stream alluvium. The ultimate source of the clastic Fe-Mn oxides is presumed to be the same coatings, selvages, and fault fillings sought by the direct sampling of joints, but has been transported as a result of lateral erosional processes.

Jan 1, 1981

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By Richard D. Hagni

The character of phosphorous-bearing minerals in the Birmingham red Iron ores and iron-bearing minerals in the Eufaula bauxite deposits in Alabama has been Intensively studied by petrographic, ore microscopic, luminescent microscopic, scanning electron microscopic, electron microprobe, and x-ray diffraction techniques. A total of 15 types of phosphorous-bearing mineral grains have been recognized in Birmingham iron ores by their characteristic sizes, shapes, and distributions. Size measurements, modal analyses, and texture analyses have permitted an estimate of potential liberation of phosphorous from the iron ores by beneficiation to be 27% In areas of previous mining and 60% in areas of current iron reserves. Fine grinding, selective flocculation, and flotation may constitute the best beneficiation technique for future research. Hematite and goethite are the most important iron minerals in Eufaula ferruginous bauxites, but pyrite, marcasite, and siderite are Important iron minerals in some varieties of ferruginous bauxite, and lepidocrocite and ilmenite occur locally in minor quantities. Although simple screening will remove the coarsest iron-bearing grains, research on the utilization of high gradient magnetic separation to reduce the amounts of iron-bearing grains is recommended.

Jan 1, 1981

By M. Y. Fisekci

This paper concentrates on subsidence measurements, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suitable methods for these conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the net- work of laser surveying over the workings of the new hydraulic mine.

Jan 1, 1981

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By Tominaga Y

Mine ventilation control is one of the most important techniques to suppress the disastrous region within a limited area, to have enough time of emergencies (ignitions, fires and so on) for underground workers. The purpose of this paper is to introduce the simultaneous controlling of mine ventilation by using, micro computer connected to various kinds of sensors. In this study, basic of mine ventilation and graph theory are used for making computer programs when the characteristic curves of fans and temperature distribution in an underground roadway network are given.

Jan 1, 1981

By Darby H. P, Vincent R. J

Sydney's Eastern Suburbs Railway from Central to Bondi Junction required the construc- tion of 10.4 km of single-track tunnel and five underground stations. Much of this work took place beneath the commercial centre of Australia's largest city. This paper discusses the general precautions taken and the specific design solutions made for such problems as support of a 15-storey building with foundations several metres above the excavation to ensure negligible differential settlement, excavation immediately below running tunnels, underpinning of multi-storey buildings, tunnelling under massive masonry retaining walls and demolition and rebuilding of part-completed structures.

Jan 1, 1981

By Reed S. C. Rogers, Robin P. Gardner, Kuruvilla Verghese

The development and use of short-lived radioactive tracer methods for the onstream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1981

By Wade E. Cooper

INTRODUCTION How accurate are past and present employee radondaughter exposure records of underground uranium miners employed in the United States? This often-debated question is essential for future substantiation of safe exposure limits. An apparent discrepancy between company-reported exposures and Mining Enforcement and Safety Administration (MESA) projected exposures was detected in 1977. For these reasons a need for an updated comparison of these exposure data was indicated. This paper gives some of the conclusions of the earlier study and compares more recent exposure records compiled by the Atomic Industrial Forum, Inc., with projected exposures based on sampling by Federal mine inspectors. EARLIER STUDY In its 1977 Annual Report (U.S. Department of the Interior, 1978), MSHA's predecessor, the Mining Enforcement and Safety Administration (MESA), reported that there was "an apparent discrepancy between Federal inspection results and company records." Both company records and MESA's projections from samples taken during routine Federal inspections indicated reductions in the average exposure of underground uranium miners from 1975 to 1977, but the MESA projections were over 4 times higher than the company-reported averages. This apparent discrepancy however, was based on a comparison of exposure data reported for all U.S. underground uranium miners. This projection more closely represented the average exposure of U.S. underground uranium mine production workers who worked 1,500 hours or more during the year. Exposures of such workers are reported each year by the Atomic Industrial Forum, Inc. (AIF) in summaries of exposure data reported to the AIF by uranium mining companies throughout the United States. (The AIF exposure summary for 1979 appears as tables A-1 and A-2 in the appendix of this paper.) Assuming that the average exposure for each exposure range category is the midpoint of each exposure range category, table 1 compares the estimated average exposures for U.S. underground uranium mine production workers who worked underground 1,500 hours or more each year in 1975 through 1977 with the exposures projected by MESA for those years. [Table 1. - Average Exposure and Projected Average Exposure for U.S. Underground Mine Production Workers Who Worked Underground 1,500 Hours or More During the Year. Company, MESA?' Reported- Projected Year (WLM) (WLM) 1975 1.59 5.68 1976 1.84 4.64 1977 1.68 4.08 1 Atomic Industrial Forum, 1976, 1977, 1978. 2 U.S. Dept. of the Interior, 1978.] Table 1 indicates that, even after adjustment to ensure better comparability an apparent discrepancy between Federal inspection results and company reported exposures for 1975-1977 exists; however, the apparent discrepancy diminished over the 3 years. Slade, 1977, explained some of the discrepancy between company records and MESA projections of miners' average radon-daughter exposures as follows: 1) Concentrations of radon daughters in some work areas can vary greatly during any one day. A variation from 0.3 WL to 17.0 WL has been measured in the same stope on the same day. 2) Seemingly simple abatement problems indicated by the regular Federal and State inspections were solved simply by manipulating the mine ventilation. 3) The methods used by mine operators to compute cumulative exposures were such that high radiation readings were seldom or never reflected in the records. For example, a work area sampled on Monday indicated a radon-daughter level equal to 0.2 WL and this was recorded. It was sampled again on Wednesday of the following week and the level was 2.2 WL. The miners were withdrawn or told to fix the ventilation, and when this was accomplished the area was sampled and found to be at 0.2 WL again. Although the miners could have been working in the higher concentration up to 6 days, this reading might never be reflected in their records. If it was recorded, only a fraction of the day on which it was discovered would be entered into the cumulative exposure calculation (time-weighted average). 4) Some of the mines visited used a mine average radiation concentration, and every employee working underground was given the same exposure per unit of time spent underground. As a result of the 1977 study, more stringent sampling and recordkeeping standards were proposed and public hearings held in 1977. The resulting new and revised health standards on radon-daughter sampling and exposure recordkeeping became effective August 30, 1979 (Mine Safety and Health Administration, 1979). Prior to these new regulations, radondaughter sampling requirements were on an "as often as necessary" basis (Code of Federal Regulations, 1978). The new regulations required practically all active work areas in underground mines to be sampled at least once every 2 weeks, with many areas requiring weekly sampling. They also required calendar-year exposure records of all underground

Jan 1, 1981

By D. R. Shoemaker

BACKGROUND AND PROJECT DESCRIPTION A 16.5 kt per day underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Small scale underground mining first began in 1920 and large scale open-pit mining was initiated in 1965, but because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for 1983. Full production of 9 Gg of molybdenum per year will be reached in 1984. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. 'The service shaft, 7.3 m in diameter and 396 m deep, will be used for personnel, supplies, development muck, and fresh air intake. It will be equipped with a large, double-deck man and material cage. A double-drum hoist will be used for cage hoisting and will handle up to a 27-t load in balance with a counterweight. Development muck will be loaded into skips in balance and a single-drum auxiliary hoist will provide secondary access. The 396-m-deep, 4.3-m-diameter development shaft will be used for initial mine development, mine exhaust air, and a slick line pass for concrete entering the mine. The development shaft is located 400 m north of the service shaft. Run-of-mine ore will be transported from one of two 1.4-kt storage pockets by a 1.2-m-wide conveyor belt located in the 10°, 1980-m-long, 5.0-m-wide, and 4.6-m-high decline. The decline conveyor belt has a centerline length of 2229 m and a vertical rise of 363 m. It will be powered by four 448 kw motors driving a single drive pulley. There will be two 1.2 m transfer belts on the surface with centerline lengths of 322 m and 542 m. All three conveyor belts will be reinforced with steel cables. On the surface, in addition to the headframes and hoist houses for the two vertical shafts, a large maintenance shop, warehouse, compressor house, change house, main office building and timber framing building have been constructed.

Jan 1, 1981