Search Documents

By Binbin He, Baiwei Lei, Rehamutula·Rouzi, Zheng Wang, Chao Li

Methane explosions are highly destructive and constitute a primary hazard affecting mine safety. Seals are commonly employed to obstruct the propagation of methane explosions within tunnels, with the aim of reducing the damage caused by methane explosions. In order to study the influence of the seals’ position on the parameters of methane explosion damage, this study takes the Lake Lynn Experimental Mine No. 501 in the United States as a background case. It investigates the methane/air explosion damage parameters at different positions of seals in a fully sized roadway using the GASFLOWMPI code. The coupling mechanism between methane explosion gas expansion and reflected waves is analyzed. Finally, the variation patterns of explosion damage parameters are analyzed based on explosion damage criteria. The results show that as the distance increases between the seal and the explosion source, the maximum overpressure and impulse at the seal decrease exponentially, and the decrease is more significant when the seal is closer to the explosion source. The maximum velocity and maximum dynamic pressure increase first and then decrease, reaching their maximum values at approximately 115 m. They are approximately 163.355 m/s and 30.485 kPa, respectively. According to the analysis of explosion damage criteria, it is found that overpressure damage is the main form of methane explosion damage. But the damage of impulse and dynamic pressure is not be ignored. The relative position between the seal and the gas expansion area significantly impacts the parameters of methane explosion damage due to the coupling effect of gas expansion and the overpressure reflected wave from the seal. When the seal is set in the gas expansion zone, the further the seal is from the explosion source, the greater the dynamic pressure damage and the more minor the overpressure and impulse damage. The closer to the explosion source, the more significant overpressure and impulse damage changes. When the seal is set outside the gas expansion zone, the further the seal is from the explosion source, the more minor the overpressure and impulse damage to the seal, and the dynamic pressure damage increases first and then decreases.

Apr 24, 2024

By Tahereh Rostami, Behnam Khoshandam

In the present paper, the recovery of mixed spent cathodes is evaluated and performed through a hydrogen reduction process. Firstly, the lithium is isolated by the hydrogen reduction process as LiOH at 600 ◦C for 15 min with 10% H2 with a flow rate of 350 ml/min. In the second step, 98.37% Li is recovered through water-leaching of hydrogen reduction products at 100 ◦C for 90 min with 50 ml/g. The filtration residual is reduced by using a carbothermic reduction process and a hydrogen reduction method. The first one is performed under an Ar atmosphere at 900 ◦C for 210 min and the second one is conducted at 800 ◦C for 150 min. The purer products are achieved using the hydrogen reduction method at lower temperatures and shorter holding times compared to a carbothermic reduction process with recovery percentages of 100%, 99.06%, and 70% for Ni, Co, and Mn, respectively. Given the importance of reducing the emission of toxic gases, the hydrogen reduction process is also a promising method for metal recycling. The obtained results also demonstrated that Li, Co, Ni, and Mn can be effectively separated from the mixed cathode material through the hydrogen reduction process as a sustainable and environmentally friendly recycling process. This study provides an impressive understanding of the hydrogen reduction process and valuable guidance for a larger-scale hydrogen reduction process.

May 3, 2024

By Hakan Akcin, Pinar Eksert

The aim of this study was the safety risk assessment of accidents that occur because of production dynamics in deep coal mining, one of the highly dangerous business class, with spatiotemporal GIS. In this study, accidents that occur at certain times during production in underground mining workplaces are discussed based on evaluations of spatial and temporal dimensions. Accordingly, various analyses have been handled using criminology science tactics and strategies such as 80–20, kernel density, space–time cube, and hot spot, which have been adapted to GIS tools. Implementations have been realized on 3D underground cartographic models covering accident data from deep coal mine workplaces in the Zonguldak-Kozlu basin in Turkey between 2019 and 2021, at an average elevation of – 400 m. Space–time cube, kernel density, and time series analyses suggest that the Annual Bonus Incentives, which are repeated every year and given before the new year, increase the psychosocial risks for employees. It has been determined that this situation can lead to problems such as poor concentration among miners and loss of focus in some shifts. Additionally, significant relationships were found between the number of accidents and monthly production progress rates as a temporal parameter. The results demonstrate that applying a reactive approach with spatiotemporal GIS to accidents in deep coal mines is becoming increasingly important.

Apr 24, 2024

By Nathaneal Williams, Corby Anderson

Rare earth elements are in high demand in the USA. Bastnaesite, a rare earth fluorocarbonate containing primarily cerium and lanthanum, is one of the most abundant sources of rare earths in the USA. This research was completed using the ore from Mountain Pass, which is the largest rare earth mine in the USA. This research, resulting in a current patent application, was done to find a way to combine flotation with novel collectors and gravity separation techniques to reach an enhanced grade and recovery of rare earth elements while rejecting the gangue minerals, calcite, barite, and silicate minerals. These minerals, particularly calcite, an acid consumer, are well known to be difficult to separate in conventional flotation of bastnaesite ore. Four collectors were examined. They were N,2-dihydroxybenzamide, N-hydroxycyclohexanecarboxamide, N,3- dihydroxy2-naphthamide, and N-hydroxyoleamide. Through this analysis, it was determined that, to obtain the desired results, flotation would be the rougher stage and gravity separation would be utilized as the cleaner stage. Bench scale flotation tests were conducted on the run of mine ore using conditions that were determined using a previously utilized Stat Ease model for testing and statistical optimization in design of experimentation. The bench tests that produced the most desirable results were then scaled up to a 10 kg float test. A concentrate from this test showed a rare earth oxide grade of 44%, while rejecting 91% of the calcite. This concentrate was used for gravity separation. Through gravity separation, it was found that another 40% of the calcite could be rejected with a final rare earth oxide grade of 47% in the concentrate.

Apr 1, 2024

By Mustafa Kumral, Mehmet Balci

Strategic mine planning centers on solving cut-off grade selection, capacity planning, and block sequencing. Even though significant knowledge has been accumulated on mine planning over the last decades, there is still potential to add value to mineral sourcing by addressing various aspects. To this end, this paper addresses two issues. The effects of (1) grade/metal distribution within a mineral deposit and (2) the economies of scale (EoS) are explored in cut-off grade selection and capacity planning. In doing so, the interdependency between cut-off grade selection and capacity planning is also considered. A case study is implemented on a metallic deposit whose grade distribution exhibits lognormal distribution to detect if grade/ metal distribution influences cut-off grade selection. Also, based on the same ore tonnage and metal quantity, six different datasets are generated with different shape and scale factors. The research outcomes indicate that deposits with lower shape and scale factors of lognormal distribution are more sensitive to metal price and discount rate changes because slight cut-off grade variations significantly change net present value (NPV). While the NPV of the deposit with the largest shape factor is $3,208,112,841 with a cut-off grade of 0.058 oz/tonne, the NPV of the deposit with the smallest shape factor is $93,617,240 with a cut-off grade of 0.027 oz/tonne. Furthermore, the case study is directed to investigate the effect of EoS on a project’s value, with a specific emphasis on the ratio of variable cost to total cost (capacity factor). Two different regression analyses are conducted based on the proposed model for optimal capacity planning and cut-off grade selection, respectively. In the first one, the absolute standardized beta values for EoS of mining and mineral processing costs are 0.736 and 0.425, meaning that capacity planning is highly sensitive to the EoS of mining and mineral processing operating costs. Meanwhile, the absolute standardized beta value for grade variability is 0.054 which means that the effects of grade variability and metal distribution are almost negligible for capacity planning. However, EoS is the most critical variable for capacity optimization. In the second regression analysis, the standardized beta values for grade variability and EoS of mineral processing operating cost are 0.573 and 0.522, so their effects on cut-off grade selection become vital.

Apr 29, 2024

By Jianbo Lan, Desheng Huang, Xiaoying Qiu, Zhaohua Ke, Liusheng Ge, Xinjin Xiao, An Guo, Qiaofa Lan

Magnesium salt rare earth enrichment (MREE) is a crucial intermediate raw material in the deep processing of rare earth elements and material preparation, serving as a front-end raw material for the synthesis of rare earth oxides. With the current disposal process for MREE, neutralization slag with high rare earth residue is generated during further extraction of rare earth from the MREE and accumulates in huge piles. Therefore, the combined disposal process of MREE and neutralization slag was put forward. MREE was solubilized using 4 mol/L sulfuric acid to achieve an endpoint pH of 0.75, dissolving the rare earth and obtaining an acid solution. The MREE and neutralization slag were added in a mass ratio of 1:2 to the acid solution sequentially. The pH of the endpoint was controlled to 4.8~5.0 for neutralization and decontamination. This resulted in the production of rare earth sulfate liquid of similar quality to the original MREE disposal process, meeting subsequent extraction requirements. The neutralization slag underwent a water washing process, with two washes (first with 0.2 mol/L acidity water at a solid-liquid ratio of 1:2 and second with deionized water at a ratio of 1:4), resulting in water-washing slag with a rare earth content of 0.24% and a rare earth yield of 97.08%. Notably, zero wastewater discharge was realized. This innovative process effectively addressed the challenges of high rare earth residue in neutralization slag and stockpile accumulation, offering valuable theoretical and practical insights for MREE disposal.

May 31, 2024

By Fika Rofiek Mufakhir, Amru Daulay, Widi Astuti, Slamet Sumardi, Lukman Hakim Nasution, Hendra Prasetia

Rare earth elements (REEs) are utilized in numerous disciplines, including chemical engineering, the nuclear industry, metallurgy, medicine, electronics, and computer technology. Recycling products containing and extracting them from effluent is necessary to satisfy the rising demand for these elements. Some studies investigate the adsorption of rare earth elements from dilute aqueous solutions to remove them from effluent. Based on the results of this study, it can be concluded that lab tests demonstrate high adsorption capacities, which vary widely depending on the adsorption type and conditions. The Langmuir, Freundlich, and Temkin isotherms usually describe adsorption isotherms. In addition, the finest models for describing adsorption kinetics are pseudo-second-order and pseudo-first-order models. The thermodynamic parameters, such as the changes in free energy, enthalpy, and entropy, provide additional information regarding the energy changes. Additional research is required to develop environmentally friendly adsorbents that can be used to remove REEs from actual mine wastewater.

Apr 3, 2024

By Ebrahim F. Salmi, Tan Phan, Ewan J. Sellers, Thomas R. Stacey

Extension of ore pass length has become increasingly critical for optimising energy-efficient underground mining operations. Long and ultra-long ore passes, spanning from 300 to 700 m, can significantly improve the functionality and viability of underground mass mining operations though suboptimal performance has an extremely adverse impact on production. The public domain lacks substantial information regarding the primary engineering, geological, and geotechnical risks and challenges associated with the design, implementation, operation, and maintenance of such long ore passes. Therefore, the aggregation of past experiences and the insights of experts assume paramount significance. An innovative methodology is introduced to address this evident data deficiency and to establish comprehensive guidelines for the resilient design of such lengthy ore passes — combining gap analysis with expert elicitation techniques. This equips design engineers with the necessary tools to formulate and adapt strategies for assessing the numerous challenges and uncertainties that invariably accompany their projects. Expert elicitation techniques are summarised, and a gap analysis is conducted with subject matter experts, from various countries, collating their extensive ore pass design experience, to create a comprehensive list of effective parameters and key risks that must be considered. Quantitative analysis of the survey results enabled the identification and ranking of the numerous factors affecting the design, operation, and maintenance of long and ultra-long ore passes and highlights the complex technical challenges (substantial damage from rock particle impact, increased dynamic mining stresses leading to failure, air-blasts and back blasts, dust, preferential flow, turbulent and dynamic material flow) that are uncommon in shorter ore passes. Additionally, increasing length heightens the probability of intersecting weak rock or discontinuities, leading to a higher risk of structural failure and instabilities. Faulting, folding, and large-scale structures are also critical geological factors to be considered in the design of such structures. The key geotechnical factor is also the rock type surrounding the pass. Experts highlighted the lack of clear guidelines for decision-making, resilient design, and construction so this work suggests future investigations to determine the complex interaction between the effective parameters, using approaches like the rock engineering system, discovery of cascading hazards, and optimal controls.

May 3, 2024

By Ulin Herlina, Fajar Nurjaman, Yepi Triapriani, Pulung Karo Karo, Slamet Sumardi, Achmad Shofi, Riska N. Tirmayani, Fathan Bahfie, Diah Susanti

The process of selectively reducing limonite ore involves adding 10 wt% sodium sulfide and using anthracite as a reducing agent in varying amounts (5, 10, 15, and 20 wt%). The research aims to optimize the extraction process by studying how factors like reduction temperature, holding time, and reducing agent dosage affect on iron and nickel content and recovery. The ideal conditions identified are a temperature of 1150 °C, a 10 wt% additive, and a corresponding 10 wt% reducing agent amount, with a crucial 60-min reduction process. X-ray diffraction (XRD) results show dominant phases like ironnickel (FeNi), iron sulfide (FeS), fayalite (Fe2SiO4), and wustite (FeO) under these conditions, indicating complex chemical interactions. Impressive X-ray fluorescence (XRF) test results precisely measure a nickel component with a 3.03 wt% and a recovery rate of 89.32%, highlighting the process’s effectiveness in extracting potential from limonitic nickel ore. The resulting ferronickel alloy has a controlled particle size of 29.23 µm. The study emphasizes the influence of sodium sulfide and anthracite dosage on the selective reduction of limonite ore.

Apr 2, 2024

By Giovanni Rubinich Moraes, Giorgio de Tomi, Irfan Ullah

The study examines productive and unproductive hours in four underground mine shifts: 6 h, 8 h, 10 h, and 12 h. Moreover, two sub-scenarios of single or two blasts examined the effect on mine utilization regarding effective working hours in underground mines. Cuiabá Mine data, the Brazilian’s largest and deepest underground gold mine, was used in both sub-scenarios. Under the first sub-scenario, which assumes two blasts per day, the 6-h shift had an effective work time (EWT) of 13 h and 30 min or 56.3% of the day. The EWT was 15 h and 20 min, 63.9% of the day, in the 8-h shift scenario. The 15-h, 30-min EWT took 64.6% of the day in both 10/12-h shifts. The 6-h scenario had an EWT of 16 h and 15 min (67.7%) in the second sub-scenario with a single blast daily. The 8-h scenario boosted EWT to 18 h and 25 min (76.7%) daily. An EWT of 18 h and 35 min daily (77.4%) was found in 10/12-h shifts. Comparisons of both sub-scenarios show that EWT positively correlates with shift length. Sub-scenario 1 has a 7.6% incremental step from 6 to 8 h, while sub-scenario 2 has 9%. EWT increases from 8-h to 10/12-h shifts by 0.7% for single and two blasts daily. Compared to the two sub-scenarios, halting operations for blasting once daily improves the EWT average by 12.5%. Reducing blasting and changing underground mining shift duration might boost economic viability.

May 21, 2024

By Lida Sun, Na Wu, Mengyang Huang, Xingxiang Fan, Yan Jiang, Shasha He, Kunbin Yang, Yang Cao

The separation of lead (Pb) and mercury (Hg) from copper (Cu) smelting acid sludge using the carbonization and acidleaching total hydrometallurgical process was investigated. The effects of the excess coefficient of sodium carbonate, excess coefficient of nitric acid, conversion time, conversion temperature, dissolution time, and dissolution temperature on the separation efficiency of Pb and Hg were studied. The test results indicated that when the dosage of sodium carbonate was 2.0 times the stoichiometric ratio, the conversion time was 1.5 h, the conversion temperature was 75 ℃, and the amount of nitric acid was 1.8 times the stoichiometric ratio. Additionally, the dissolution time was 1.0 h, the dissolution temperature was 60 ℃, the ratio of liquid–solid was 5:1, and the separation efficiency of Pb and Hg was 98.72%. This study demonstrated the advantages of a short, simple, and environmentally friendly process for separating Pb and Hg from Cu smelting acid sludge, providing complete separation and introducing a new technology.

May 30, 2024

By Z. M. Beiranvand, M. Moghaddasi, A. Naeimi, Y. Naami, M. Raoufi

Titanium iron oxide and nickel-chromium coatings were applied on low-carbon steel substrates using the high-velocity oxygen fuel thermal spraying process. The microstructure, phase composition, and hardness of the coatings were analysed using scanning electron microscopy, x-ray diffraction, and microhardness tests. The phase analysis confirmed the formation of oxide compounds in the coatings. The average microhardness values for titanium iron oxide and titanium iron oxide-nickel-chromium coatings were measured at 580 HV and 970 HV, respectively, under a 100 g load. The corrosion resistance of the coatings was evaluated in a 3.5% sodium chloride solution using electrochemical impedance spectroscopy (EIS) and polarisation tests. The results indicated that the nickel-chromium composition exhibited superior corrosion resistance, which was attributed to its low porosity, preventing solution diffusion into the substrate. Wear behaviour was assessed using a pin-on-disk test with a tungsten carbide pin as the counterbody. The incorporation of nickel-chromium into the titanium iron oxide coating resulted in an 80% reduction in weight loss, indicating significant improvement in wear resistance. These findings suggest that nickel-chromium-modified titanium iron oxide coatings enhance both corrosion and wear resistance, making them promising candidates for industrial applications.

May 8, 2026

By Z. Duran, M. Genc, B. Erdem, T. Dogan

This study aims to develop a model for particulate matter concentration during the loading process in open pit mining. The researchers conducted simultaneous measurements of particulate matter and meteorological parameters and collected samples to determine the moisture content of the loaded materials. The analysis used 7,895 measurement data points from gypsum and limestone quarries, employing two data analysis programs, SPSS® and Waikato Environment for Knowledge Analysis, to derive equations for predicting particulate matter release. In the modelling, particulate matter measurements were the dependent variables, while meteorological parameters, laboratory measurement results, and loader bucket capacities were the independent variables. The classical regression models did not adequately capture the dependent variable, thus, the researchers explored the decision tree approach for further modelling. The M5P algorithm was used to generate regression equations for the different data sets, and the findings showed that the models had a satisfactory degree of predictive capability. The number of fine particles released during loading is influenced by various weather factors. Temperature, humidity, wind speed, and station pressure can all affect the dispersal of these particles. Additionally, the moisture content of the loaded material and the capacity of the loading equipment contribute to this process. The M5P decision tree algorithm, which is rarely used in particulate matter concentration models, provides an innovative approach to developing local concentration estimates for non-coal surface mining.

May 8, 2026

By F. Mulenga, S. Ncube

Rock fragmentation methods in open pit gemstone mining have developed to give priority to safety, environmental sustainability, and crystal integrity. Though effective, traditional drill-and-blast techniques can generate vibrations, adverse emissions, and structural damage, all of which could be detrimental in fragile geological settings. Costs, application in hard rocks, and operational inefficiency remain issues, despite the fact that mechanical excavation and evolving thermal and hydraulic technologies have provided some solutions. In response, there has been a growing interest in non-explosive alternatives, particularly soundless chemical demolition agents. This paper provides a comprehensive evaluation of non-blasting rock fragmentation techniques with an emphasis on the efficiency, economic considerations, and operational constraints of soundless chemical demolition agents SCDAs in gemstone mining. Soundless chemical demolition agents technology has shown promising results in preserving gem purity and reducing environmental impact, despite ongoing challenges. These include increased reaction times that hinder output, decreased performance in saturated or high-stress environments, and temperature sensitivity. The contextual relevance of soundless chemical demolition agent application in lateritic regions, such as Zambia, is discussed based on published studies and reported operational experience. Developments in formulation chemistry, fracture modelling, and borehole design have also demonstrated promise in overcoming current limitations. This review identifies the main factors that affect soundless chemical demolition agent performance and brings together reported strategies that can improve their use in high-value mineral extraction through a comprehensive review of recent studies. Ultimately, this article supports a paradigm change towards excavation techniques based on state-of-the-art non-explosive technology that are safer, cleaner, and more accuracy focused.

May 8, 2026

By W. J. van Wyk, W. I. Mahne, G. Priest, C. du Toit, W. A. Liebenberg

Prior to the Coalbrook disaster in 1960, bord-and-pillar mining of the number two seam in the Witbank coalfields often resulted in small pillars with low factors of safety. At the Goedehoop Colliery, number two seam pillar stability is also affected by top and bottom coaling, while at Greenside Colliery, stability was further reduced by additional loading from a surface mineral residue deposit. This compromised the stability of the number two seam workings, impacting the safe mining of the overlying number four seam reserves. To extend the life of mine of both operations, an alternative risk management approach using designated enhanced monitoring districts was implemented to safely mine the number four seam reserves. This paper presents the use of geophone arrays to monitor micro-fracturing in number two seam pillars and the interburden between number two seam and number four seam, thereby enabling early detection of potential instability during overmining of the number two seam. Risk was assessed using fault and event tree analyses to determine acceptable failure probabilities. Automated seismic data processing distinguished micro-fracturing from noise, supported by extensive evacuation procedures for effective risk management. This approach facilitated the safe extraction of 4.70 Mt of number four seam coal. The study quantifies the efficacy of geophone monitoring in optimising coal recovery over low factors of safety pillars and assesses the application of Van der Merwe’s (2019) time-based formulae for pillar stability analysis for this project.

May 8, 2026

By K. Thambi

Environmental rehabilitation has increasingly become a central concern in the regulatory and fiscal landscape governing South African mining operations. A key issue within this domain is the extent to which mining entities may claim tax deductions for expenditures incurred in fulfilling their environmental rehabilitation obligations. The Supreme Court of Appeal's decision in Sishen Iron Ore Company (Pty) Ltd v Commissioner for the South African Revenue Service [2025] ZASCA 16 addresses pivotal questions regarding the tax treatment of such expenditures. The judgment offers authoritative clarification on the interpretation of the Income Tax Act 58 of 1962—specifically sections 11(a), 11(c), and 36(11)(e)—as they pertain to mining activities and the environmental responsibilities imposed under the Mineral and Petroleum Resources Development Act 28 of 2002. This commentary critically examines the multifaceted implications of the Sishen ruling, highlighting the intersection of statutory interpretation, operational realities, and environmental accountability within South Africa’s mining sector.

May 8, 2026

By C. I. Kim, I. C. Paek, I. K. Tae, P. J. Thak, U. C. Han, K. S. Jong

This paper analyses the energy consumption according to the type of dump scroll track during skip discharging in an inclined shaft hoist for an open pit mine. For the purpose of the project, it was necessary to set up an equation for a geometrical locus of a skip dump scroll track, and from the need for technical engineering and study purposes, to derive equations for two track types by using cam design theory (cosine track and linear accretion track). Skip discharging is analysed using discrete element method software, and dynamic simulation of its run is performed using Visual Nastran software. The energy consumption during skip discharging can be calculated from the rope tension obtained by dynamic simulation, and graphs obtained from the simulated results using discrete element method and Visual Nastran software. From this, the study demonstrates that the energy consumption at the cosine track is always lower than that at the linear accretion track, without regard to the property change of a payload depending on grain size distribution.

May 8, 2026

By Gregory Carli

Mining operations rely on high-duty, mobile and semimobile equipment to move rock, process ore, maintain roads and sustain site services. Typical mining fleets combine loading and hauling assets with production, logistics and maintenance equipment, which are all expected to operate at high load factors, over long hours and in harsh environments. The mining industry is under pressure to decarbonize their operations and to transition to lower-emission technologies. While decarbonization options are well understood for stationary process equipment, challenges remain regarding how to decarbonize heavy-duty mobile emission sources. This article presents the methodology and findings of a structured assessment of low- and zero-emission pathways for mobile mining equipment. The approach is data driven and equipment centric, evaluating technology readiness, commercial and technical viability, and the financial implications of alternative powertrains including battery electric, hybrid electric, hydrogen fuel cell/combustion and low-carbon fuels such as renewable diesel and biodiesel. Supporting infrastructure requirements are also reviewed. Baseline attributes such as engine/motor power, duty cycles, energy intensity and typical purchase price are compiled into an equipment matrix, with alternatives matched by output power to ensure performance comparability. Capital expenditure (CAPEX) and operating expenditure (OPEX) are calculated conservatively from public sources, with OPEX combining energy/fuel costs and maintenance rates that reflect powertrain complexity.

May 1, 2026

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people, and in 2024 produced 38.5 Mt (42.4 million st) of iron ore and 52.5 Mt (57.9 million st) of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan and Liberia, focusing on iron ore and coal extraction to support steel production.

Apr 1, 2026

By Tanya J. Gallegos, Mojisola A. KunleDare, James V. Jones III, Charlotte E. Riggs

The United States Geological Survey (USGS) provides scientific information for the Department of Interior and the nation, consistent with its original mission expressed in the Organic Act of 1879 (43 U.S.C. 31): “the classification of the public lands and examination of the geological structure, mineral resources, and products within and outside the national domain.” Legislation such as the Energy Act of 2020 and the 2022 Infrastructure Investment and Jobs Act (43 USC 31l) and recent executive actions (Executive Orders 14154 , 14153, 14241 Secretary’s Orders 3417, 3418, 3422, 3436) underscore the importance of mineral resources and focus USGS activities on mapping and assessing mineral resources, with a particular focus on those presently identified as critical, both in ground and above ground in mine wastes. This article reviews selected activities and accomplishments by the USGS Mineral Resources Program related to critical minerals in 2025. Highlights include a new List of Critical Minerals, a first-ever national mine waste inventory, international minerals partnerships, mineral resource assessment advancements, and national data collection activities and outcomes of the Earth Mapping Resources Initiative (Earth MRI). The selected contributions are not comprehensive but are intended to demonstrate USGS leadership in critical mineral mapping and assessment, the importance of domestic and global partnerships, and the breadth of research activities that are responsive to national needs and priorities.

May 1, 2026