Search Documents

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

The aspect ratio (mill diameter/mill length) of autogenous and semi autogenous mills varies widely and can be as high as three or as low as 0.5. The literature on the subject of what effect aspect ratio has on grinding mill performance or energy efficiency is almost non-existent. However, at the design stage of many grinding circuits the subject is often vigorously debated amongst metallurgists. In this paper the performance characteristics of mills with different aspect ratios are examined to determine whether process performance characteristics are a function of aspect ratio and whether high aspect ratio mills are any more or less energy efficient than low aspect ratio units. Data from both pilot and full-scale mills are used for this purpose in open and closed circuit configurations.

Jan 1, 2007

By W. H. Furlonge

WHILE fulfilling professional engagements, my travels over this portion of the Transvaal have been quite extensive—always on horseback however, so that anything like a thorough investigation of the ground passed over has been necessarily impossible; still, the more minute examination of certain small areas, coupled with general observations, has enabled me to form some idea as to the prominent geological features of the country as a whole. Anything like a complete or comprehensive description is indeed out of the question, as there are no proper maps of the country and the facilities for observation are limited. A large plateau, called the "High Veldt," stretches from east to west across the Transvaal. It is generally level, or gently rolling, and has an average elevation of 6000 feet above the sea; it is destitute of timber, and in fact greatly resembles the western prairies of North America. Rock-outcrops are not common in it. It terminates very abruptly to the east and northeast, the descent of 2000 or 3000 feet into the mountainous country that occupies its borders being made in a

Jan 1, 1890

By Jiacheng Wang

The current state of thick seam coal mining methods is illustrated in three typical cases of thick seam longwall mining, each pointing out the outstanding achievements in top-coal caving mining and large cutting height mining in China. At the same time, based on current thick seam mining practices in China, some problems urgently need to be solved. These include improving the recovery ratio of coal reserves, determination of overburden strata pressure, shield support selection, supporting methods for large cross-section in-seam roadways, top coal bulk flow theory, and gas flow and control technology. In addition, the rational production capacity should be studied from both economic and technological perspectives in order to optimize coal recovery and efficiency.

Jan 1, 2011

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

The concentrated efforts now being directed towards the development and application of monitoring and control techniques have now resulted in their widespread use in UK mines together with evidence of benefits resulting from their application. There is little doubt that the longwall method of producing deep mined coal will continue but will be made more reliable and efficient with the aid of control technology. The major fields of research and development work are concerned with planning and design of mines and mining equipment; management and engineering information; and automation of coalface, tunnelling and transport systems. The principal achievements now in widespread use are: the standard computer system MINOS, widely applied to mine transport, coalfaces and mine environment; extensive use of machine condition monitoring leading to condition-based maintenance; underground automation of conveyor systems and guidance systems for ranging drum shearers and boom-type roadheaders are being widely introduced.

Jan 1, 1985

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

By Brad Ross

? Value in number of children ? Polygamy common ? Support of extended family and friends ? HIV/AIDS ? Not a culture of savings ? Minimal mechanical experience ? Supportive ? Unintended hindrance ? Mining claims ? Export Permits Lack of funding

May 1, 2011

By R. Matikainen

Since the Brundtland Commission in 1987, the use of natural resources has been an issue of global concern. Minerals are among the most important Earth resources and will definitely be essential for the development of societies also in future. Increasing scientific effort is needed not only to discover new deposits, but also to promote resource management in ecologically and socially sound way. Sustainable resource management is essentially a multidisciplinary challenge of developing life-cycle analysis and recycling of non-renewable resources from local to global scale. It offers great opportunities for geological surveys not only in EU, but all over the world to contribute positively to the welfare and sustainability of societies.

Jan 1, 2003

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

(SECRETARY'S NOTE.) The following discussion of the papers of Van Hise, Emmons, Lindgren and Weed, read at the Washington meeting, February, 1900, and printed on pp. 282 to 498 of this volume, comprises communications to the Secretary, received at various times before the Richmond meeting, February, 1901, and, for the most part, presented at that meeting. These communications are introduced at this point in the present volume, in order that they may precede the papers of Vogt, hemp, Lindgren, Rickard, etc., presented at Richmond, and therefore not forming part of the material considered in them. Since many of the contributors have mentioned in one communication several of the papers referred to, no attempt is here made to divide their remarks and distribute the fragments under separate headings. In each contribution, however, the several topics are indicated by subtitles. R. BECK,* Freiberg, Saxony : Prof. Veal Hise's Paper.-The paper of Prof. Van use (p. 282) represents a great step of scientific progress, in that the circulation of underground waters has never before been presented with such clearness, ill the light of modern chemical and physical knowledge. The theories of the formation of ore-deposits which follow the author's general survey of the currents and solvent power of atmospheric waters in the earth's crust do not, indeed, seem to be novel, being essentially an amplification of Le Conte's views; but the proofs adduced in their support are in many particulars so original that no one can read without profit this portion of the paper. Entirely new (though largely in agreement with the papers of Emmons and Weed, presented at the same meeting of the Institute) are the sections dealing with the formation of the rich sulphides of the precious metals, and especially the regeneration of normal sulphides, such as galena, etc., in vein-zones immediately beneath the ground-water level. Nevertheless, it appears to me that Prof. Van Hise, in the course of his most instructive exposition of unquestionable, yet still locally limited, phenomena, has been too much biased in favor of the " descensionists." This is indicated by the small importance which he attaches to the intimate genetic relation between epigenetic deposits and the plutonic hearths of the earth's interior.

Jan 1, 1902

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

By Lachlan Gilchrist

MEASUREMENTS of resistivity by methods involving the use of two current electrodes and two potential electrodes in general collinear with the current electrodes have been made extensively in geophysical investigations. In the method developed by Wenner and made use of by Gish and Rooney, and later in a modified form by Lee, the distance between the current electrodes is divided into three equal parts by the potential electrodes. In one of the methods developed by Schlumberger prospecting methods and by Koenigsberger, one current electrode is placed at considerable distance from the other and potential measurements are made in the immediate neighborhood of one of the current electrodes. The method is described as the single current electrode method, and the effect of the distant current electrode is considered negligible or a correction is made for the effect in the calculation of the resistivity. Usually the correction that is introduced is based on the calculated effect for measurements made in a homogeneous conducting material. The useful application of these methods in prospecting for minerals, of course, is in regions where nonhomogeneous conditions exist. In many of these conditions it is very doubtful whether the effect of the distant current electrode may be neglected, except for measurements in the immediate neighborhood of the "single" current electrode, and corrections based on homogeneity of the medium will necessarily be inadequate. In order to obtain a degree of symmetry that would preclude the necessity for corrections for the distant electrode and that would simplify interpretation, it appeared desirable to use a central current electrode and a set of distant end current electrodes symmetrically placed about the central electrode as shown in Fig. 1 and to provide by means of auxiliary resistances that the currents passing into the earth at the distant end electrodes should be equal. Circumstances did not permit the operation of this plan in complete detail but a degree of symmetry was obtained by using a central current electrode and two distant collinear end current electrodes and by taking measurements along a line passing through

Jan 1, 1931

By Victor Rudenno

Feasibility studies for mining projects traditionally involve in their final stages a lengthy process of repetitive trial and error discounting, in calculating the discounted cash flow rate of return resulting from the respective yearly after-tax cash flows. Also, probability analysis and sensitivity analysis (in particular) require extensive additional calculations with each change of any project parameter . These inefficient repetitive procedures have two unacceptable results: 1. they are not flexible enough to allow ready analysis of dependent parameters , and 2. they require resort to high-capacity centralised computing facilities with their inherent impersonality, rather than a convenient and available desk calculator - a factor of particular importance to top mining management. Such problems can be overcome if the mining project can be represented by a reasonable straightforward mathematical economic model. The most flexible and appropriate model has been found to be one in which a maximum and minimum value for each of n parameters are supplied to a program which determines a large number of systematic combinations of parameter events and then statistically analyses them to determine the resulting coefficients of the model. In this paper the authors discuss the selection of the most appropriate type of model and outline the steps followed in its development and application.

Jan 1, 1977

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987