Search Documents

By S. Ozbilen

"Al-Li binary alloys with nominal Li contents of0.15, 1.1and2.8 (in wt%) were aged naturally at room temperature for two months, aged at low temperatures ( 65 and 1 OOEC) for up to 2 months and aged artificially at 190EC for 4 days after water quenching to 25EC following solutionizing at 530EC for 20 minutes. Ageing behavior of these binary alloys were studied by Vicker's Hardness measurements and DSC thermal analysis. Thermal analysis results indicate the formation of GP zones of Al-Li system in Al-2.8wt%Li binary alloy. In the same alloy, rapid quenching from one phase region (a) gives rise to precipitation of small o' particles in a matrix (a) with still high supersaturation. During ageing of this alloy below lOOEC an additional transformation, i.e., GP zone formation occurs proceeding at a very high rate which is described on the basis of the theoretical analysis for the quenched Al-Li system proposed by Khachaturyan et al [6]. Ageing at temperatures below 11 OEC takes place slowly by the formation of small d' particles of lower thermal stability than the quenched-in d precipitates in addition to GP zones resulting in an increase in hardness compared to water quenched samples. During artificial ageing, GP zones transform by dissolution to d' precipitates while d' particles already in the microstructure coarsen during under aged condition at which hardness increases with time till peak aged condition.IntroductionIn binary Al-Li alloys the d' (Al3Li) fully coherent internally ordered inetastable phase of Li2 structure with a=0.4038d [1-5] forms homogeneously between 120 and 190EC before the formation of stable d' (A!Li) phase and cause the superior mechanical properties. This is due to an appreciable age hardening effect resulting because of the d' precipitation during ageing [1]. The response of d' to decomposition and its formation kinetics have been studied previously and it is believed that the decomposition of the a-supersaturated solid solution occurs in a two stage process; i.e., a 6 d' (Al3Li) 6 d(A!Li). Khachturyan et al [6] theoretically investigated precipitation of the d' phase and gave an interpretation of the transformation paths of the quenched Al-Li alloys. They predict that the disordered supersaturated solid solution congruently orders, and then the uniformly ordered solution decomposes into ordered regions that differ in Li-content. Finally, ordered d' phase forms in the disordered matrix."

Jan 1, 1998

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

By Firkin GR, Allen RJ

Sulphide Corporation Pty. Limited has roasted a number of different zinc sulphide concentrates on its sinter machine which pro- duces zinc-lead sinter for an Imperial Smelting Furnace, and results have varied widely. The differences are considered to be functions of !concentrate particle size and reactivity. Amdel have used differential thermal analysis to examine these concentrates and two major effects have been found. Firstly, in concentrates 1containing small quantities of pyrite and chal- L [copyrite, heat is liberated at 400¦C to 650¦C [by oxidation of these two sulphides. Secondly, as particle size decreases, heat release from the oxidation of zinc sulphide commences at flower temperatures and rate of heat release In a sinter bed, the presence of some rite and chalcopyrite would help to heat the cc sulphide to ignition temperature in a orter time, while a finer concentrate would sult in roasting being completed more ickly. Both of these effects result in a arper flame front and minimise the chance heat and combustion fronts being mismatched. is theory is supported by sintering results tained by Sulphide Corporation. As a result

Jan 1, 1975

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

By L. W. Kempf

THE thermal conductivity of aluminum alloys is of considerable indus-trial importance. This is particularly true in such applications as inter-nal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determina-tion, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate-values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz1 as applying to metallic elements and later shown by Lorenz to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance.

Jan 1, 1937

By Cyril Stanley Smith, Earl W. Palmer

FOR several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been publishedl 1,2 † except for the electrical conductivity at 200° C., which is given in the appendix of this paper. LITERATURE ON THERMAL CONDUCTIVITY OF COPPER ALLOYS The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey's determinations4 were carried out on the alloys used by Lees5 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the

Jan 1, 1935

By Cyril Smith

FOR several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some inter-esting general relationships between the thermal and electrical conductivi-ties for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 ? except for the electrical conductivity at 200° C., which is given in the appendix of this paper.

Jan 1, 1935

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

By Turan Uysal, Thierno Saidou Barry, MURAT ERDEMOGLU, Mustafa Birinci

Nonbauxite ores such as aluminum silicate clays and coal fly ashes have been widely considered as potential resources of alumina (Al2O3). The interest focused on these ores is due to their high alumina content. Over the years, in countries where there are little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process is not economical, alternative processes have been explored. Among these processes, acid leaching is seen as the most attractive process. In the acid leaching process, heat treatment for thermal activation to destruct the refractory structure of the minerals in the ores is generally recommended as a pretreatment method. Recently, the applicability of high energy ball mills, which are useful for mechanical activation as a pretreatment method before leaching, has attracted much attention. This is a short summary of our previous review [1], giving the details of alumina manufacturing from thermally and mechanically activated clays and coal fly ashes by acid leaching.

By Murat Erdemoğlu, Turan Uysal, Thierno Saidou Barry, Mustafa Birinci

The rapid development of the global alumina and aluminum industry is straight coupled with the demands and the needs of these materials. Nowadays, the only well-known accessible resources to produce alumina and aluminum are bauxite ores. But bauxite ores are limited, and the remaining exploitable reserves do not have high contents in alumina. In countries where there is little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process are not economic, alternative resources for alumina have been explored. The most attractive resources for replacing bauxites are aluminosilicate clay minerals and coal fly ash. The important processes developed for the recovery of alumina from these sources are acid leaching and alkaline leaching processes. The acid leaching is known as the most efficient in which thermal and mechanical activation are included for improving the performance of the process. The objective of this review is to give a comprehensive insight on the production of the alumina from thermally or mechanically activated clays and coal fly ash by hydrochloric, sulfuric, and nitric acid leaching processes.

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By G. K. Burgess

(New York Meeting, October, 1913.) 1. COOLING AND HEATING CURVES BY G. V. BURGESS AND J. J. CROWE. § 22. THE results published in Professor Howe's paper 10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels 11 containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by' the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to -0.1 sec. for recording .time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain's derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12. The observations were taken in vacuo on cylinders 5/8 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thereto-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by, platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 6, 1913

By A. R. Barnes, R. Pandher, T. Shannon, P. Gover

Following the closure of the Glencore Zinc Brunswick mine, the Glencore Brunswick Smelter has transitioned to treating external feeds, and currently treats a number of secondary Pb-Zn concentrates. Processing these concentrates has in some cases been challenging due to the diverse mineralogy of the feeds. Certain feeds are difficult to ignite or show inadequate sulphur removal during oxidation on the sinter strand, while in other cases, combinations of feeds produce a sinter with unsuitable properties for further handling. This paper discusses two methods developed in collaboration with XPS Consulting & Testwork Services to characterize these feeds prior to processing them and to identify which ones are most likely to pose challenges during processing.

Jan 1, 2014

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By Robert C. Edmiston

"Further, we search for the veins by observing the hoar-frosts, which whiten all herbage except that growing over the veins, because the veins emit a warm dry exhalation which hinders the freezing of the moisture, for which reasons such plants appear rather wet than whitened by the frost," Georgius Agricola, De Re Metallica, 1556 In view of Agricola's statement, made in 1556, the concept of using the heat released by oxidizing sulfides as an ore guide can hardly be considered a product of twentieth-century technology. In fact, thermal exploration has received relatively little attention in modern times compared to other potential field geophysical methods. There have evolved, however, two basic approaches to thermal exploration for subsurface heat sources. These are 1) the measurement of surface temperatures by infrared, thermal imagery and 2) the measurement of geothermal gradients in exploratory drill holes.

Jan 1, 1974

By Robert C. Edmiston

The measurement of temperatures in exploratory drill holes yields information on regional and local geothermal gradients and mean surface temperatures. This data may be beneficial to the mining geologist interested in the occurrence and oxidation of metallic sulfide minerals or to the mining engineer interested in subsurface temperatures or water movement. Additionally, the estimation of mean surface temperatures by the projection of thermal gradients to the ground surface provides data on which to evaluate infrared imagery as an exploration tool. Temperature measurements in 30 diamond drill holes in the Silver Bell mining district of Arizona show that a regional geothermal gradient of 2.45°C per 100 m increases to 3.03°C per 100 m near the ground surface. It is also found that an anomaly in the mean annual surface temperature of 0.5°C is associated with the shallow occurrence of disseminated sulfides. Changes in the geothermal gradient due to topography, water circulation, and formation changes also occur.

Jan 1, 1976