Search Documents

By J. R. Ruark

Because of the importance of oil-shale reserves the Bureau or Mines resumed research investigations in this field beginning in 1944. The Bureau early decided to build a Large-scale demonstration plant to accomplish the dual purpose of obtaining design data and to produce crude shale oil for refining studies. Two 40-ton-Capacity batch N-T-U (Nevada-Texas-Utah) retorts were completed for this purpose in 1947. After a preliminary operation, the plant was used to investigate process variables of air rate, recycle gas rate, and shale particle size and crude. Correlations obtained from these variables are presented in this report. Researchers concluded that recycle gas was not necessary for efficient operation of the process. Short comings of the batch method of processing the oil shale are pointed out in the report. Several periods of prolonged production operations were carried out. During these periods, the retorts were operated to produce as much crude oil per day as possible. The lifetime operation of the N-T-U retorts was divides into three periods, namely, preliminary operation, process variable study, and production operation. During the preliminary operation, 187 runs were made with a total of 7,596 tons of raw shale used to produce 3,688 barrels of crude shale oil. During the process variable study, 179 runs were made with a consumption of 7,494 tons of raw shale and a production of 4,218 barrels of crude shale oil. The production operation consisted of 554 runs in which 22,457 tons of raw shale was used to produce 12,359 barrels of crude shale ail. The overall total for the lifetime operation of the retorts consisted of 920 runs with a total consumption of 37,547 tons of raw shale and a production if 20,265 barrels of crude shale oil.

Jan 1, 1956

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By Lawrence Y. Marks

During the mineral survey of the Bob Marshall Wilderness and study areas by the author in 1971, 1973, 1974, and 1976 (Marks, 1978), the area designated Reservoir-North (RARE II No. H1-485) in January, 1979, (U.S. Forest Service, 1979) was examined, along with other lands adjacent to the earlier study areas. However, the 1978 open-file report covered only areas originally designated for study. The present report on Reservoir-North is based on earlier work. No work has been done in the area since 1976. Mineral Appraisal Reservoir-North RARE II area (No. H1-485) is in the Northern Disturbed Belt which has been identified as having high potential for natural gas accumulations and lesser potential for oil accumulations (Mudge, 1978). Oil and gas lease applications in the area, indicate interest by oil companies.

Jan 1, 1981

By T. M. Ruff

The U.S. Bureau of Mines has developed a portable, inexpensive teleoperation system for mobile hard-rock mining equipment. The system was tested on a compact loader-trammer in a simulated stope. The teleoperation system includes radio remote control and computer-assisted navigation. A recent enhancement includes video cameras mounted on the machine to provide visual information to the operator. This system allows the operator to remain in a safe location while operating the machine from a distance, thus increasing both operator safety and mining productivity.

Jan 1, 2010

By L. C. IlsLey

[In 1922 a conference of representative coal-mine operators, cable manufacturers, mining-machine manufacturers, and representatives of the United States Bur eau of Mines vas held at the Pittsburgh Experiment Station, regarding suitable cables for use with permissible raining machines. This conference recommended that the Bureau investigate rubber-sheathed trailing cables in order to obtain specifications for tests leading to approval for rise with mining machines. Effective until such time as an investigation could be made, the bureau asked the several manufacturers of approved mining machines to recommend cables for wise with their machines. In general the Cables recommended tentatively approved. Arrangements for the tests were completed in 1927. Concentric-type cables were investigated first, and Reports of Investigations, Serial No. 2909, covering the tests, was issued in January, 1929.]

Jan 1, 1929

By J. L. Shultz

The investigation of organic compounds in respiratory coal dust by high-resolution mass spectrometry has shown that the organic components differ (1) with particle size, (2) with rank of coal, (3) in coals of same rank from different coal seams, and (4) in respirable mine dust and respirable coal dust (prepared) from the same mine. The eight respirable mine dusts studied are from coal seams in the Appalachian region where the incidence of coal workers' pnumoconiosis is relatively high. The molecular weights of the major organic components vary greatly among these respirable mine dusts; three show strong concentrations of polynuclear aromatic hydrocarbons.

Jan 1, 1972

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By Michael J. Pazuchanics

This report documents the current status of the U.S. Bureau of Mines ongoing investigation of the use of adaptive signal discrimination (ASD) systems to distinguish between cutting coal and cutting rock. Cutting-tool forces and vibrations were measured in the laboratory using both conical bits and roller cutters in a linear-cutting apparatus for several material samples and two cutting directions. A number of ASD systems consisting of one or more signal classifiers were trained and tested to study how data window size, type of signal feature, and combining (polling) of classifier results influence system performance. The results show that ASD system recognition rates can be improved by increasing data window size, removing air-cutting portions from the signal data, overlapping data windows, and combining (fusing) information at various levels of ASD system operation.

Jan 1, 2010

By R. B. Anderson

As a part of a Bureau of Mines program on the conversion of coal to liquid and gaseous fuels, the kinetics of the Fischer-Tropsch synthesis on iron catalysts was investigated. Nitrided catalysts were studied at 21.4 atmospheres using feed gases ranging from 2H2+1CO to 0.25H2+1CO, and at 7.8 to 21.4 atmospheres using 1H2+1CO gas. The overall apparent activation energy increased with increasing carbon monoxide content of the feed gas from 19.5 kcal/mole for 2H2+1CO to 23.7 for 0.7H2+1CO. The rate of synthesis with 1H2+1CO feed increased linearly with operating pressure from 7.8 to 21.4 atmospheres. A semifundamental rate equation of the form [r=a'PH2 0.6pco 0.4- ?r0.5PH200.5] was shown to fit the data satisfactorily. The relative usage of hydrogen to carbon monoxide decreased with increasing conversion, passed a minimum, and then increased. Apparently water is the principal primary product and carbon dioxide is produced by subsequent water-gas shift reaction. In another group of experiments water, carbon dioxide, argon, and methane were added to 1H2+1CO feed to a nitrided iron catalyst. Argon and methane were only diluents. Carbon dioxide was a slight inhibitor and water vapor was a strong inhibitor to the rate of synthesis. Water accelerated the water-gas shift and usually increased methane production. Important factors of catalyst geometry in determining rate were found to be particle size and extent of reduction. Apparently the active portion of the catalyst is confined to a layer of 0.01 to 0.02 cm from the external surface of particles. A special solution was made of differential equations relating re¬action at the catalyst surface to diffusion in pores of the catalyst for spherical particles with an active layer surrounding an inert core. The equation derived expressed the experimental data reasonably well. Diffusivities determined by this equation varied from 3 to 24X10-6 cm2/sec; these values are of the same magnitude as observed for the diffusion of gases in liquid. The appendix presents a group of synthesis experiments at pressures of 21.4 to 103 atmospheres. In this range the rate of synthesis on nitrided iron catalysts increased with pressure to the 0.74 to 0.84 power.

Jan 1, 1964

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By S. A. Matthes

This Bureau of Mines report describes a system for the dissolution of metal and mineral samples using a microwave heat source. Samples and an acid mixture are placed in sealed polycarbonate vessels. The vessel contents are heated using microwaves, digested for 2 min, and quickly cooled. After the solution is brought to a final volume, the vessel contents are heated an additional 2 min in the microwave oven. Using this method, a slag, a feldspar, and a Ni-Cu alloy were dissolved and analyzed by atomic absorption spectroscopy. Values obtained for Na, K, Cu, Ni, Si, Mg, Mn, Ca, Al, and Fe agreed with certified values and had an average relative standard deviation of 1 pct. This system results in a significant savings in time and expense over traditional methods of sample dissolution, and is ideal for preparing solutions for analysis by atomic absorption, plasma optical emission, or X-ray spectroscopy.

Jan 1, 1983

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By Pamela J. Watson

The U.S. Bureau of Mines has demonstrated in laboratory tests that drilling with surface-charge-neutralizing concentrations of polyethylene oxide (PEO) polymer solutions simultaneously improves penetration rates and extends bit life. The applicability of this additive to improve drilling performance in coal measure rocks was demonstrated under field conditions at an abandoned mine land site in Pennsylvania and a producing coal mine property in Ohio. Penetration rate improvements ranging from 15 to 50 pet were obtained when core drilling through a variety of coal measure lithologies. Drilling cost analysis indicates that the small added cost of using the polymer is more than offset by the savings that result from demonstrated increased drilling penetration rates, which translate into drilling cost savings of about 10 to 30 pct. This report also gives chemical analyses of a variety of coal measure rocks and some corresponding local drilling water samples, obtained from a wide geographical base, along with threshold concentrations of PEO required to effect the improved drilling performance in these rocks. From these data, the threshold PEO concentrations needed to ensure improved drilling performance can be estimated for any coal measure rock suite. Proper techniques for mixing PEO solutions are also presented.

Jan 1, 2010

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972