Search Documents

By Andres M. Baquerizo, Jeremiah J. Filjones, Nicholas Feldt

The Estates at Acqualina located in Sunny Isles Beach, FL, is comprised of two, ocean-front, 50-story, luxury towers with podiums and villas. With city regulations now requesting that above-grade floors be limited to commercial or residential units, parking facilities for the tower structures were situated within two levels of underground basement parking. However, ensuring dry excavation through south Florida’s highly pervious limestone, immediately adjacent to the beach where the groundwater table is very shallow, can be extremely challenging and costly for developers. In recent years, significant advances have been made to overcome this challenge with the innovative use of deep soil mixing to create a “dry hole”, assisting in the construction of foundations and underground usable space for parking, storage, etc. The “dry hole” system includes a soil mix bottom seal, with soil mix secant pile walls in combination with auger cast deep foundation elements to support the future structure. This approach enables groundwater control to greater depths than can be achieved by conventional sheetpiling and dewatering. For the Estates at Acqualina, a successful turnkey, design-build joint venture between two foundation and geotechnical contractors resulted in a dry excavation to 34 ft (10.4 m) below grade and to a record- breaking auger cast pile depth of 182.3ft (55.6 m), all within an aggressive 26-week schedule to deliver the “dry hole” excavation for the first tower. This presentation will discuss the logistics, quality control, design, and safety for the different techniques involved. INTRODUCTION AND BACKGROUND The Estates of Acqualina is a pair of 50-story luxury towers located on Sunny Isles Beach in Florida with a two-level underground basement for parking. The project’s location just steps away from the Atlantic Ocean, geology, and high-water table created a challenging project. The owner, Trump Group, contracted the joint venture of HJ Foundation and Hayward Baker (HJ/HB) to design-assist-build a system to control the groundwater, allowing the 2-story underground parking structure to be constructed. In order to accomplish this task, the JV utilized an installation technique known as deep soil mixing. This technique mixes the in situ material with a cement slurry to create a very impermeable material called “soilcrete”.

Jan 1, 2019

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By Sara Moshfeghi, Seyyed Majdeddin Mir Mohammad Hosseini, Abolfazl Eslami

"Due to variety of current pile bearing capacity methods based on the cone penetration test (CPT), for optimum design, it is necessary to evaluate the performance of such methods in different geotechnical conditions. Geotechnical databases including piling and in-situ testing records have been recognized as useful tools for analysis, design and economical construction. In order to evaluate pile bearing capacity methods, AUT-CPT&Pile database has been compiled including 450 full scale pile load tests and CPT sounding records. This database consists of different pile types with a relatively wide range of geometries and various soil conditions. Forty three records of piles driven in sand deposits were then employed to evaluate effects of ultimate capacity interpretation criteria from load displacement diagrams. The Davisson offset limit criterion, the Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter were compared to estimated capacities from ten CPT based design methods currently used in practice. The Brinch Hansen 80% criterion and the load at the displacement of 10% of the pile diameter lead to reasonable results, the Brinch Hansen 80% criterion showed less scatter. For evaluating the accuracy and the precision of CPT-based methods, the results were compared to estimated capacities. Results of comparison indicate that the CPT-based methods mainly predict the pile capacity withreasonable accuracy.INTRODUCTIONAmong the different approaches of estimating the pile bearing capacity, in-situ tests, especially, the cone penetration test (CPT) are favored due to the cone similarities with piles in modes of installation as well as fast and continuous profiling. This trend is practically well established where deep foundations are to be constructed in soft to medium subsoil deposits (Eslami and Fellenius, 1997; Mayne and Niazi, 2009).Employing different design methods results in a wide range of values which complicates the selection of an appropriate one to determine the pile bearing capacity. Several studies by Briuad and Tucker (1988), Eslami and Fellenius (1997), Abu Farsakh and Titi (2004), Schneider et al. (2008) and Eslami et al. (2011) confirm disparity of different design methods predictions. Thus, for optimum design, it is necessary to evaluate and compare the performance of current methods.Geotechnical databases are known as helpful tools in research and practical applications for optimizing analysis and design and are mainly used for management and interpretation of data, evaluation of design methods, calibrating LRFD or ASD design factors, etc. Pile lateral and axial load tests are examples of databases in geotechnical engineering. A summary of several CPT and pile load test databases is presented in Table 1."

Jan 1, 2017

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Garland Likins

Where soil conditions are favorable, augercast piles have significant economic advantages, but they also have some uncertainty due to the in construction methods. To confirm structural integrity, static testing can be performed on a small sample of piles. Other Non-Destructive Evaluation methods like Pulse Echo are frequently specified for a large percentage of the remaining production piles. However, such NDE methods require testing the pile after the grout/concrete has hardened. If problems are found, then the repair or replacement can be relatively expensive. The confidence in the quality of these piles can be improved by automatically monitoring the grout pumped as a function of depth during the grouting phase of installation. If a low grout volume is detected, the pile can be redrilled and regrouted immediately while the piling rig is still in place and the grout still fluid. This considerably reduces remedial costs. To be effective, such installation monitors must accurately determine both grout volume and depth during installation and be rugged simple to operate. Such an equipment can be of great help to the installation crews. The assurance gained may reduce the need for subsequent NDE tests. The quality of inspection of driven piles depends heavily on the inspection personnel. While inspection is critical in a good installation, it is sometimes assigned a low priority. Inspection personnel in many cases are technicians with little pile experience. They may not understand the project needs or even how the pile driving equipment works. The task is often monotonous and any distraction makes accurate record keeping difficult. In some cases inspection is totally ignored for lack of qualified personnel. Electronic systems can automatically and accurately monitor driven pile installations and include documentation of certain hammer performance parameters. This paper describes equipment available and routinely in use for automated monitoring of both augercast and driven piles and demonstrates applications on typical construction sites. The paper also discusses benefits and limitations of the alternative NDE tests. KEYWORDS: Augercast Piles, Piles, Installation Monitoring, Pulse Echo Method, Integrity Testing

Jan 1, 1999

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Brain E. Ladd

A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (?) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at ?/D of about 7.5% and ultimate end bearing resistance at ?/D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a ?/D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using ?/D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.

By Brian E. Ladd

"A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (d) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at d /D of about 7.5% and ultimate end bearing resistance at d /D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a d /D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using d /D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.INTRODUCTIONAuger-cast-in-place (ACIP) piling was developed in the 1940’s and patented in 1956 (Neely, 1991). Since patent expiration in 1973, ACIP piles are abundantly used in the United States, particularly in the southeast. However, most literature addresses driven piles constructed in sand and clay with lesser discussion of drilled piles. Conventional design methodologies (a- method, ß-method, SPT or CPT correlations, etc.) are based on data derived from numerous projects in a great variety of geologies. O’Neil (2001) notes that there are significant levels of uncertainty in the “universal” databases as evidenced by coefficients of variation of 0.35 to 0.40 for geotechnical parameters (su, SPT-Nvalue, etc.) used to estimate pile capacities.There is a need to develop local databases developed from data obtained from load tests that measure shaft resistance and end bearing. This paper presents the results of load tests conducted on axially loaded auger-cast-in-place piles constructed in the Inner Coastal Plain geology of North Carolina. Shaft resistance, end bearing, and movements that initiated mobilization of these resistances are described. The information presented herein can be used to refine geotechnical correlations and parameters applied in auger cast pile design methodologies."

Jan 1, 2017

By Sam Warren, Antonio Marinucci, Genesis Z. Figueroa, Anne Lemnitzer

Drilled Displacement Piles (DDP) provide an ideal deep foundation solution that combines the benefits of ground improvement with traditional advantages of piling systems. This paper consolidates data from 20 construction projects in which more than 30 DDPs were installed and tested axially. High quality site exploration data (e.g., Cone Penetration Test and Standard Penetration Test) were evaluated to derive geotechnical analysis parameters. The test sites consisted of mostly mixed soil types with strongly stratified layers of sand, silt, and clay. Pile diameters ranged between 40 cm and 61 cm. Test results were compared with predictive methods developed specifically for DDPs as well as methods used in general geotechnical practice. The accuracy of the empirical methods is presented in terms of total pile capacity, pile length/diameter, and soil type. The large majority of all examined methods underpredict the in-situ pile capacities. It was also found that the difference between the tested and predicted capacity is strongly related to the level of improvement in the surrounding soil due to the piles’ installation. A general comparison between predictive axial accuracy and the observed level of ground improvement upon installation is also discussed.

May 1, 2022

By Emad Farouz, Ali Albatal, Ehab Shatnawi

Drilled shafts are deep foundations that can carry heavy loads by transferring them to deeper and stronger soil or rock layers.  The paper focuses on the drilled shafts installed in the Potomac Clayey Formation in the northern part of Virginia. The paper shares the lessons learned from using steel casing during drilling. Two load tests were done on drilled shafts with 75-centimeter diameter and 21-meter length. The first load test failed to reach the loading capacity, while the second load test succeeded after changing the installation method. The paper explains the subsurface conditions and the design methods used to estimate the axial capacity of the drilled shafts. The paper gives details about the installation methods and the reasons for not reaching the axial capacity with a standard installation method. The paper offers useful insights into how the construction method affects the axial capacity of drilled shafts.

Oct 7, 2024

By Kanagarajah Ravishankar

Drilled shaft (caisson) foundations are extensively used in the past. In the central part of New Jersey, the soils consist of silt and clayey silt overlying Triassic age shale bedrock. The shale is friable and generally severely weathered and highly fractured. The shale crumbles readily into small fragments. In general, the shale is encountered in shallow depth. Subsurface investigations indicated that the upper part of the shale is very soft, highly weathered, and able to advance through soil exploration methods. The underlain formation is relatively hard and required rock coring techniques for sapling. Individual core recoveries ranged from 10 to 100 percent and Rock Quality Designations (RQD) vary from 0 to 90 percent. Although several methods available to estimate the axial capacity of drilled shafts, it is a difficult task for the designer choose the suitable method due to self disintegrate nature of the shale. In the recent years several bridge foundations have been constructed using drilled shafts founded on shale rock in the vicinity of the central New Jersey. Based on load tests carried out on drilled shafts during construction, subsurface exploration, and laboratory tests, suitable methods for determining axial capacity of drilled shafts is analyzed. This paper presents the findings of the field tests and suitable methods to determine the axial capacity of drilled shaft founded on soft shale. Key words: Drilled shaft, axial capacity, Osterberg load test, shale.

Jan 1, 2006

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By Sanjeev Malhotra

The American Petroleum Institute (API) method of predicting pile capacities in sands is reviewed. Factors that influence pile capacity such as soil parameters, pile parameters, loading effects and installation effects are listed. In addition, the simultaneous occurrence of physical phenomena such as grain crushing, pile shaking, stress-redistribution and plugging add to the uncertainty in the prediction model. To better understand the method of prediction, each parameter and the associated uncertainty is revisited. It is evident that these factors are inter­related and sometimes compensating. This discussion also draws attention to the influence that pile installation procedures can have on pile capacities and highlights the need for field experience with various pile installation procedures for designers. In summary, the strength of the method lies in its simplicity and ease of application, but the possible savings generated by an improved method are too substantial to ignore.

Jan 1, 2000

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Paul W. Mayne

The axial load-displacement-capacity and load-transfer response of deep foundations can be conveniently assessed by geophysical piezocone tests that provide four independent readings with depth, including tip stress (qt), sleeve friction (fs), porewater pressures (ub), and shear wave velocity (Vs). The penetration data (qt, fs, and ub) of the CPT are utilized to obtain the pile side friction (fp) and end bearing capacity (qb) while the shear wave measurements provide the initial stiffness. Within an elastic continuum framework, the axial pile deflections are calculated and an approximate nonlinear response is obtained by modulus degradation from small-strain response (G0) to intermediate- and large-strains (G). The continuum solution permits separation of load transfer along the sides and proportion to the base. Applications are shown for case studies involving an end-bearing drilled shaft, two friction-type drilled shafts in Alabama and Georgia, and a "Class A" prediction involving driven pipe piles in residuum of the Atlantic Piedmont geology. Load-transfer data were available for the drilled shaft foundations.

Jan 1, 2002

By Prasanta Paul, Aminul Islam

"Nhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area at Jawaharlal Nehru Port Terminal (JNPT), Uran, Maharashtra. The proposed container terminal yard is located on a recent reclamation on the Thane Creek, which was developed by land-based reclamation method. The underneath soft marine clay was treated, using vertical band drains and placement of surcharge upon.Settlement of the reclamation during its construction was monitored using settlement plate installed at +4.8m CD elevation which was above the highest high water level.This paper examines the settlement behaviour of the reclamation during the ground improvement works. The geotechnical parameters are back-analyzed by the authors from the field settlement results and the concerned preloading details. The back analyzed coefficients of consolidation due to horizontal flow (Ch) are compared with laboratory determined parameters and the estimated value, using Asaoka Method (1978). The authors also studied field compression ratio [CR= Cc/(1+e0)] vs. the compression ratio determined by laboratory test using back-analysis method.1. INTRODUCTIONNhava Sheva (India) Gateway Terminal Private Limited proposed to construct a container terminal yard, comprising a back-up area of approximately 27 hectares, complete with associated buildings and services on a part brownfield/ greenfield site. The back-up area shall include a heavy duty block paved pavement with band beams for electric Rubber-Tyred Gantry Crane (eRTGC) alongwith surface water drainage system and other services including area lighting, provision of fire-fighting facilities , sources for potable water and power.Based on the Employer’s Requirement and the available geotechnical investigation report, ground improvement scheme is designed by the construction contractor. Ground improvement works included the installation of prefabricated vertical drains and subsequent placement of surcharge for accelerating the consolidation of the underlying soft marine clay."

Jan 1, 2015