Search Documents

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By Joseph E. Chilton, Robert J. Timko, Charles D. Taylor

No regular monitoring of methane is required in areas of gassy coal mines outby the mining face. Methane ignitions that have occurred in mine outby areas indicate the need to provide better protection to workers. Handheld methane monitors are now used by some miners to make periodic measurements of methane at the working face. The IYONI II gas detector which is incorporated into a miner’s cap lamp and worn on a miner’s helmet can continuously provide an alarm signal whenever methane levels exceed a set level. Tests were conducted to evaluate the performance characteristics of this methane detector by measuring response times with methane gas supplied through a calibration fixture or adaptor. Other response time tests were performed with the detector in an environmental test box. Performance was also evaluated in a full scale test gallery where face methane emission and underground ventilation were simulated. Procedures for calibration by response time measurement of the IYONI II detector have been developed. In limited testing, the IYONI II detector was found to reliably detect the presence of 1 percent by volume methane.

By Rad B. Langston, Ted J. Williams, John A. Marjerison, Rimas T. Pakalnis, Tom M. Brady, Doug C. Bayer, Mark J. Bren

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

This chapter presents MSHA data on mine employment and active mining operations during 1986-1995. Figures 3-1 through 3-10 show, for each commodity, the location of mine operations in 1995, and employee hours and active mining operations by year during 1986-1995 for mine operators. For coal and nonmetal operators, the number of active mining operations and the number of employee hours decreased over the 10-year period. For metal operators, the number of active operations decreased, while the number of employee hours increased. For stone and sand and gravel operators, the number of active operations and the number of employee hours remained about the same. Figures 3-11 and 3-12 show that over the 10-year period, there was an increase in the proportion of hours worked by contractors in coal mining, while the overall employment decreased. For metal, nonmetal, stone, and sand and gravel combined, the proportion of contractor hours increased, with overall employment also increasing. Table 3-1 shows the distribution of hours worked during 1986-1995 by commodity and type of operation. For coal, the majority of hours worked were in underground mines. For metal, nonmetal, and stone, the largest number of hours worked were in mills and preparation plants. For sand and gravel, all work hours other than office were in surface mines. [ ]

Jan 5, 2000

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

Acid pollution from abandoned mines causes serious contamination of major streams in coal mining areas. In Pennsylvania alone it is estimated that 3000 miles of streams are devoid of fish and plant life because of coal mine effluent.1 The pollution arises because water and oxygen react with iron sulfide in the mine cavity to produce sulfuric acid and iron sulfate, which later find their way back into surface streams. Two general approaches to the problem are possible: (1) prevent the acid-forming reaction from taking place, (2) treat the acid mine water after it is formed so that it will not be harmful to the ecology when discharged into streams and other surface waters. The work described in this report belongs in the first category - it was based on the assumption that acid formation in the mine cavity can be prevented by keeping water (one of the reactants) out of the mine. This was to be accomplished by-forming a waterproof seal over the mine cavity which would prevent the seepage of surface water into the mine. It was planned to form such a seal at or near the surface of the ground by applying latex to the soil. Ideally a dilute latex would be applied to the soil and would penetrate to a depth of two to three feet below the surface where it would be coagulated by reacting with a constituent of the soil or by other means., A seal below the surface of the soil would have several advantages over a surface seal - it would not be subject to destruction by traffic, frost or vegetation and, more important, it would allow the use of the top soil for many agricultural purposes. A preliminary feasibility experiment was performed prior to application for the present grant. It showed that it was indeed possible to form a sub-surface seal by means of latex. A core of soil was obtained locally (Wayne, N. J.) by driving a 6.5 cm inside diameter steel pipe about 100 cm long into subsoil for a distance of 71 cm. The soil was retained within the pipe for this experiment. A part of the free space above the soil in the pipe was charged with water, and the seepage rate of the soil after it had become saturated was 15 ml/min under a total head (wet soil plus supernatant column of water) of 92 cm. After the supernatant water had drained completely, 100 ml of 5% rubber latex was added and allowed to seep into the soil. This was followed by additional water and the seepage rate was found to be 2 ml/min under the same head. This seepage rate remained unchanged when remeasured on the following day. Since there was no visible evidence of the latex in the collected drain water it is presumed to have been retained by the soil.

Jan 1, 1972

SMCRA contains five principal regulatory provisions that form the basis for its implementation: Performance Standards Performance standard safe intended to ensure that all surface mining is conducted in a way that protects the environment and the public and ensures that the mined land is restored to productive use following mining. Permits Before developing a surface or underground coal mine, an operator must have a permit issued under SMCRA. An application for a permit to conduct a surface coal mining operation is a detailed document that consists of text and numeric data describing the proposed mining and reclamation. Information must be furnished on pre-mining environmental conditions, existing land use, proposed mining and reclamation, how the performance standards will be met, and the post-mining land use. This provides the regulatory authority with the information necessary to determine that the operation can be conducted in accordance with the regulations. Performance Bonds Before a permit can be granted, an operator must post a performance bond sufficient to cover the cost of reclaiming the site in the event the operator fails to complete reclamation. The bond is not fully released until all performance standards have been met and reclamation of the site has been determined to be successful after five years in the East and Midwest, and after 10 years in the arid West. However, the bond can be partially released as various phases of reclamation are completed. Inspection and Enforcement If a violation of SMCRA or of a state surface mining and reclamation law is observed, an inspector issues a notice of violation to the operator. The violation must be corrected within a specific time, and the operator may also have to pay a fine based on the severity of the violation. If the violation is not corrected, acessation order is issued to immediately stop active coal mining, and the operator must pay a fine. If a violation is especially serious (for example, creates an Following reclamation, the land was immediately put back into agricultural production. Today, grain and corn crop yields have continually exceeded targets. 2 imminent danger to public health or safety or causes significant damage to land, air, or water resources) the inspector immediately issues a cessation order. An operator must correct all violations in order to obtain permits for new mines. Lands Unsuitable For Mining Congress recognized that certain coal deposits cannot be mined without permanent damage to unique cultural or natural resources. As a result, SMCRA protects these resources in two ways: It prohibits mining within the boundaries of national parks, forests, wildlife refuges, trails, wild and scenic rivers, wilderness and recreation areas; in areas which will adversely affect sites listed on the National Register of Historic Places; and within a restricted distance of occupied dwellings, public roads, buildings, parks, schools, churches, and cemeteries; and Provides a process that allows anyone whose interests may be adversely affected by proposed mining to petition to have specific lands designated unsuitable for mining.

Jan 1, 1992

By G. J. Conroy

Cable whip occurring during normal movement of a shuttle car can result in a personnel hazard and excessive tensions in the cable. This Bureau of Mines report discusses preferred payout and reel-in torque settings to reduce cable whip. A simplified adjustment procedure is described.

Jan 1, 1974

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

By James R. Jones

"The General Leasing Law, which provides for the leasing of deposits of coal, oil, oil shale, gas, phosphate, and sodium in public lands, was approved February 25, 1920.One of the outstanding features of this legislation is the fact that it opens for prospecting and exploitation lands and deposits which have been withdrawn from public use, some of them for several years, pending enactment of legislation better fitted to control the mining and utilization of the particular mineral deposits referred to. These lands are not only made available to the public, but they are opened up under a system which defines better than was ever done in the pas the rights which may be acquired under it.The oil operator, for example, under this legislation will know definitely the extent of the rights he has acquired, as well as the legal conditions under which his expensive drilling and other work of exploration are to be conducted. No longer will he be harassed by the possibility that while he is spending his capital in drilling operations in an effort to make a discovery of oil, his legal rights be contested, in which event the superiority of his claim can only be upheld -- if at all -- after long and expensive litigation. By the same token the coal operator will now be free from the embarrassing restrictions of the old coal-land laws respecting the amount of such land which may be purchased by one person.At the same time that these advantages are being enjoyed by the operators, the public will be guarded against wasteful methods of drilling and mining the oil and gas, and coal deposits, and the other mineral substances enumerated in the act, to the end that these products of Nature, which can not be replaced, may be utilized with a minimum of loss."

Mar 1, 1920