Search Documents

By Virginia Lawson, Adam Price

The rougher flotation stage is used to reject liberated gangue at a coarse size. Base and precious metals due to their high specific gravity tend to recycle in the grinding circuit and report to the flotation circuit at a finer size than the gangue from which it is being separated. Generally liberation levels of greater than 50% are achieved in roughing and thus a portion of the feed can be immediately upgraded to final concentrate. The proportion increasing as the amount of liberated mineral in the feed increases. Scalping out concentrate from the rougher can reduce the size of the subsequent regrind and cleaner circuits. Examples of alternative process design for circuits demonstrates that you don’t need large volumes to effectively recover all of the minerals – you need smart flotation. Several case studies will be presented where circuits can be significantly reduced in size by designing smarter – not larger. This paper describes case studies to test the amenability of the Jameson Cell to produce final concentrate from rougher feed. Metallurgical performance and plant design implications are discussed. Froth flotation has been used extensively for mineral concentration for over 100 years. Although the flotation cell design has changed, it has generally simply increased in capacity rather than increase in efficiency. Cell capacities of over 600 m3 are now being used in rougher flotation particularly for the lower grade ores where the amount of surface area for flotation is deemed less significant than the required volume. The plant design volume in rougher flotation comes from laboratory batch flotation tests and/or pilot plants. The volume required for the plant is calculated based on the laboratory residence time multiplied by a scale- up factor. Examples of laboratory to plant scale-up design are given in Dunne et al. (2010 part 2). The factors are usually between 2 and 3. A laboratory residence time of 10 minutes would equate to a plant design residence time of 25 minutes using a 2.5 factor. The volume of the required flotation cells can then be calculated using the design tonnage and volumetric throughput. This scale-up factor takes into account the differences in performance between batch flotation efficiency and full scale plant. The differences are likely related to inefficiencies of bubble particle contact in large cells as well as froth recovery, which is essentially complete in a batch cell. Flotation cells, such as the Jameson Cells, are smarter designs that improve bubble/particle collection, bubble/pulp separation efficiency and operate with high froth recovery rather than simply getting bigger. The Jameson Cell was designed on the principal of improving the collection efficiency of fine particles by separating the contact zone from the separation zone and having the bubbles generated by the plunging jet shearing and entraining air. This means the method of bubble generation is not impacted by the wear of mechanical equipment as it the case in other flotation devices. Jameson Cells make bubbles less than 600 micron in size under most operating conditions (Ding, 2016).

Jan 1, 2019

"In conjunction with Banick Mercur , Wright Engineers Limited designed the first multi-stage aqueous pressure oxidation system in an alkaline environment in North America. A three-stage slurry heating and slurry pressure let-down with heat recovery was an innovative approach to the problem of high energy cost with the low sulphur content of the ore. The design of this system required solving a number of problems associated with heating and pumping of slurries at pressures up to 3230 kPa and temperatures in excess of 220°C. Wright received an Award of Merit in October 1989, from the Canadian Consulting Engineering Awards Committee in the Process Category for its design of the Mercur pressure oxidation system.The Mercur Mine is located at the south end of the Oquirrh Mountains in Tooele County about 65 miles by road from Salt Lake City, Utah, U.S.A. The original mill was designed to process 5000 tpd of oxidized gold ore in a carbon-in-leach (CIL) circuit. A new ore treatment system was required to treat the substantial quantities of refractory ore reserves which could not be treated economically in the existing mill. The new pressure oxidation circuit makes the refractory ore amenable to gold recovery by oxidation of the sulphides contained in the ore .Wright Engineers Limited was commissioned by Barrick Mercur Gold Mine Ltd ., a wholly-owned subsidiary of American Barrick Resources, to design the pressure oxidation facility. This followed completion of a feasibility study by Wright which showed that the project was technically and economically viable.Work on the feasibility study began in 1986, detail design commenced in February 1987, and was completed in December 1987. Mechanical installation was completed in January 1988, and slurry feed began in February 1988. The plant has operated since June 1988 without major interruption . Wright was responsible for engineering, procurement and construction management for the addition of the 750 tpd pressure oxidation circuit to the existing mill and also had commissioning responsibility.Major unit processes involved in the pressure oxidation facility are ore thickening, three-stage slurry preheating, pressure oxidation and three-stage slurry cooling with heat recovery, stearn generation, propane and oxygen storage and a video graphic display process control system were included in the scope as process anciliaries.The pressure oxidation increases gold recovery from the refractory ore by conventional CIL from as low as 35% to more than 86070. A patent has been granted for the process."

Jan 1, 1989

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994

By R. S. James, S. P. Goff, A. E. Armitage

"Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province. Copyright"

Jan 1, 1996

By H. Zniber El Mouhabbis

Ore dilution or stope overbreak increases the cost of production and ultimately reduces the profitability of a mining operation. The adverse economic impact of ore dilution is due to the added costs associated with the mucking, haulage, crushing, hoisting, milling, and treatment of waste rock or low grade ore in the hangingwall and footwall. One factor that could have a significant influence on stope overbreak is the undercutting of the stope into the walls. Undercutting stope walls is often necessary, in particular in narrow vein mines. Moreover, equipment size has a role in drift sizing where stope undercutting may become a must in order to fit the mobile equipment while respecting legal clearances.

May 1, 2009

By François Charette

High stress conditions in weak rock masses lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock failure. Typical support systems combine various reinforcement and support mechanisms to provide the required convergence control and retainment, but results are often mitigated by failure of surface liners, shotcrete and tendons. The paper reviews differing requirements of support and reinforcement for different failure types. In addition, the mechanical performance of a new reinforcing tendon is presented and analysed in view of the field requirements. Field tests results are presented.

May 1, 2011

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Sang-Kyun Woo

The electric power conduit (EPC) in Korea has been constructed since 1978. Facing the challenge of safety and sustainability of the EPC, it is urgent to develop an inspection strategy and maintenance system for the structure based on the concept of life-cycle management. This paper introduces the newly developed mobile inspection and diagnostic system of the EPC. The novel aspect of this particular system is the integration of non-destructive mobile inspection techniques with BIM (Building Information Modeling) and LBS (Location-Based Service). BIM is an ideal tool and platform for developing an inspection and diagnostic system, and RFID (Radio Frequency Identification) is a useful tool to construct USN (Ubiquitous Sensor Network) for LBS. The goal of this research is to establish an EPC inspection and diagnostic system concept based on BIM and LBS using RFID. In this research, a BIM model of OPENTBM tunnel for EPC will be established to show the integration of 3D CAD with the inspection data. An EPC?s maintenance database, which includes the deterioration types of the structure, inspection records, and repair methods, was designed to interact with the BIM. The system will be implemented by the BIM with the related database, in which the construction geometry and all related information are stored. The proposed system was designed to utilize the inspection and diagnostic system under the USN environment using RFID in EPC directly.

Aug 1, 2013

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant's operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009

Sustainable Development SAFETY ?Safety is the most important element of sustainability. ?One bad experience or incident can mar a company?s reputation for a long, long time. ?News travels faster than ever ?Internet, blogs, texting, peer-to-peer communication, etc. and unfortunately sometimes the information is not always accurate. ?Rarely do we hear in the news about the mining companies or projects that are done safely ?we always hear about the exceptions. ?Safety is just like TQI / TQM ?the process of improving can never stop.

May 1, 2010

By G. Vibert Douglas

"Gold occurs in Nova Scotia in three ways, saddle reefs, fissure veins, and fossil placers. Of these the saddle reefs are the commonest. They have been the source of most of the gold and have also been the subject of most of the literature on the gold occurrences.The Meguma or Gold-bearing series of Nova Scotia is a conformable succession of quartzite's and slates, possibly Precambrian in age, which have been folded into a number of anticlines and synclines that strike (Fig. 1) roughly east and west. This folding has been termed Acadian and is probably a westward continuation of the Caledonian revolution in Britain. It may have started in the Ordovician and continued through the Silurian and into the Lower Devonian. It was followed by the intrusion of the great Devonian granite batholiths. It is thought that the mineralization is connected with the late phases of the cooling of the granite. As the name saddle reef implies, the veins form on the crests and flanks of the anticlines, possibly in the synclinal troughs as well. The beds favoured by the solutions are the slates. The reason for this is apparent when it is realized that in order to fold over 30,000 feet of sediments (the thickness of the Meguma according to E. R. Faribault) through p radians of arc it is necessary to have a differential movement between the top and bottom beds of p times the thickness of the sediments. In the case of the Gold-bearing series, in which strong quartzite beds lie between incompetent slate beds, most of this differential movement was taken up in the slates. The evidence for this is the remarkably fine drag folding and the intense shearing and comminution of some of the beds of slate (Fig. 1). The quartzites exhibit some shearing and faulting, but there is little doubt that the greater permeability lay along the incompetent slate beds. The mineralizing solutions followed these beds and also passed from one slate bed to another through a joint or fault in the intervening bed of quartzite. These joining veins are called angulars in Nova Scotia. Within the veins the gold is in shoots and the real problem is to find out what controls the position and extent of the shoots."

Jan 1, 1954

By M. Sutherland

"Increased efforts to improve mine safety have led to various successful forms of ground control in Canadian underground mines. At Inca Limited's T-3 Mine in Thompson, Manitoba, a perimeter blasting method has been implemented in jumbo drilled development headings.The technique utilizes an increased number of perimeter blast holes in the drill pattern while decreasing the linear charge density of explosives in any individual perimeter hole. The decrease in perimeter charge density means less blast damage to the surrounding structure.The benefits realized include increased safety through less loose ground and substantially less scaling time, less overbreak and improved long-term drift stability. This paper highlights the development and implementation of the perimeter blasting program.IntroductionThompson Mine Thompson Mine is a 6000 ton per day underground nickel mine located just outside the city of Thompson, 400 miles north of Winnipeg. The mine is serviced by the T-I shaft and by the T-3 shaft. The shafts are 10 000 ft apart and are connected on several levels with the deepest operating levels at T-1 and T-3 being 4000 ft and 2400 ft respectively.The T-3 Mine presently produces 52% of the total Thompson Mine production and 65070 of the 3000 ft of mine development each month. Current development of the 5 million ton 1, C orebody below 2400 level at T-3 will maintain these production and development ratios.Depending on equipment requirements, development headings at T-3 Mine vary in size. The 1, C ramp, at 17 1/2 ft wide by 10 1/2 ft high, is presently the largest development heading at T-3. Fifty- two per cent of the development footage is done with four Gardner Denver two boom electric /hydraulic jumbos and one Gardner Denver one boom electric /hydraulic jumbo. The remaining 48% is driven with hand-held jack-leg drills."

Jan 1, 1990

By A. Warczok

The mechanisms and kinetics of copper oxidation and reduction have been investigated in small scale thermal gravimetric experiments as well as in laboratory pilot scale, packed bed reactors. With blister copper flowing gravitationally down through a packed bed of ceramic particles, counter-current to low oxygen containing combustion gases, the rate of oxidation was found to be very high due to the large surface area created. Similarly, reduction by flowing copper through a packed bed of charcoal lead to rapid de-oxidation. Based on these laboratory measurements, fundamental rate data have been obtained. Modeling of industrial sized packed bed reactors using the laboratory results, opened up the possibilities of developing a new, very intensive, continuous process for copper fire refining. The developed mathematical model together with a computer process simulator, allowed for the design of the industrial-pilot installation to be built and tested at the ENAMI Paipote smelter in Chile.

Jan 1, 2007