Search Documents

By Dan Plazak

The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [ ] to equivalent confinedaquifer drawdowns [ ]:

Jan 1, 1994

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By I. I. Inculet, M. A. Bergougnou, J. D. Brown, R. M. Quigley, D. K. Faurschou

"Coal from Hat Creek, B. C., has been successfully beneficiated to remove ash while retaining calorific value by a dry electrostatic separation process using a fluidized bed for triboelectrification. Two samples of Hat Creek coal used in the beneficiation experiments have been characterized particularly with respect to their mineral and clay content. The calorific value recovery exceeds the simple dry coal recovery because of the heat lost in altering the clay minerals of the ash fraction during burning. Recoveries and ash contents of the beneficiated coal are comparable to recoveries by water washing, but the dry process avoids the potential water pollution problems.IntroductionProposals have been made which suggest an interim Canadian coal production target for the end of the century which will require a four- to fivefold increase over the 1977 production. This implies a nominal annual growth rate of about 6070 to achieve a production rate of 115 to 140 million tonnes/year. Whether or not this target is realistic, it is becoming increasingly evident that coal must be utilized more fully on a world-wide basis. The crisis in Iran has provided the latest stimulus to renewed interest in Canadian coals for domestic use and export.The emerging new era of coal utilization for fuel and chemical feedstock will not, however, generally tolerate the level of coal technology which prevailed prior to the availability of abundant cheap oil and natural gas. Economic, environmental and resource management considerations will necessitate, for example, the use of improved methods of beneficiating coal. Continued development and application of conventional processes, principally aqueous, involving heavy media and cyclones will solve many of the problems. However, less conventional processes may be preferable or necessary in certain applications."

Jan 1, 1980

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981

By David Burgess

Natural gas is a general term applied to the gas obtained from oil or gas wells. It is the most widely used of all gaseous fuels. The principal disadvantage in the use of this and other gaseous fuels is the difficulty encountered in the storage and transportation of large quantities in the gas state. Handling in the liquid state is possible, but reduced temperatures are required since methane (table 1) is the principal component of most natural gases that are used as fuels. Actually, liquid storage has been utilized both here and abroad;3 however, the Cleveland disaster4 has pointed out the need for a critical evaluation of the hazards involved in the storage of this cryogenic fuel. Accordingly, a program was undertaken to obtain basic data that could be used to assess these hazards. In this report, the factors to be considered in an evaluation of the fire and explosion hazards associated with any fuel are each discussed briefly. These factors are then used to assist in the design of experiments for the evaluation of the hazards associated with liquefied natural gas (LNG) relative to those associated with other common fuels. Experiments have been conducted on the vaporization of LNG, the mixing of LNG vapors with air, the effect of temperature and nitrogen dilution on the limits of flammability of methane in air, the burning rates of LNG and other fuels, flame radiation, and extinguishment of fires above liquid pools. Based on the results of these experiments, LNG can be stored safely in suitably designed above-ground tanks surrounded by earthen dikes in much the same manner as gasoline.

Jan 1, 1962

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By G de Jong, W Sunyoto, M Cloos

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Ertsberg mining district is a 100 km2 area in the highlands of Papua, Indonesia. The district hosts mineralised and barren, outcropping and hidden porphyry and equigranular intrusions. There are at least six major (100+ m wide) porphyry intrusions identified from surface and underground mapping and drill cores. These are the Grasberg Igneous Complex (GIC), Karume porphyry, Lembah Tembaga porphyry, Ertsberg Stockwork Zone porphyry, Kay intrusion and the Wanagon intrusion. Recent deep drilling adjacent to the GIC identified a new hidden porphyry at depth, the Gajah Tidur (Sleeping Elephant), which extends south-west beneath the Kucing Liar skarn. Other named small porphyry dykes and plugs in the district include the West Grasberg, North Grasberg, Idenberg, South East and Zaagkam intrusions. The largest equigranular intrusion is the multiphase Ertsberg diorite.Igneous activities occurred in a relatively short span (<1 million years) from about 3.4 Ma to 2.7 Ma ago, based on U-Pb zircon dating. The various intrusions in the district related to ore mineralisation are high K and appear to have been derived from the same parental chamber, based on similar whole rock rare earth element patterns. Radiogenic Nd- and Sr-isotopic variations indicate that there were multiple recharge events into the parental chamber.The larger intrusions and all economic mineralisation occur in a 4 km wide zone that parallels the N60W-trending axis of the Yellow Valley Syncline (YVS), one of the large folds generated during collisional tectonism. Intrusion pathways at ~3 Ma were localised into dilatational areas in a late and/or post-collisional NW-trending, left-lateral strike-slip zone with Riedel shear offsets between the major fault zones. An early phase of lower K magmatism produced small intrusions in the south-west limb of the YVS.CITATION:de Jong, G, Sunyoto, W and Cloos, M, 2015. Composition, lithochemistry and radiogenic isotopes of porphyritic and equigranular intrusions in the Ertsberg mining district, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 347–356 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months' operation.

Jan 1, 1979

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

By William J. Campbell

Evaluation by the Bureau of Mines of published expansion values for magnesium oxide shows significant variation in values, which may be attributed to sample variables, experimental errors, or systematic differences between measuring techniques. To eliminate the sample variable in measuring expansion, thermal expansion characteristics of a high-purity polycrystalline magnesium oxide were determined by 21 cooperating laboratories using one or more of the following techniques; X-ray camera, X-ray diffractometer, dilatometer, interferometer, and telemicroscope. All expansion values were corrected by the author to a single reference temperature of 25° C. Linear expansion was expressed as a power series in the form of the following equation. Expansion (percent) = [[ A + B (?t) + C (?t)2] ?t 104] The constants, A, B, and C, were determined by least square techniques for X-ray camera, X-ray diffractometer, and dilatometer data separately, and for combined data of all five techniques. Expansion values are tabulated from 26° C. to 1,400° C. in 2° C. intervals using constants derived from X-ray camera data. Below approximately 500° C., expansion values obtained by dilatometric and interferometric methods are significantly lower than those by X-ray methods; above 500° C., this bias decreases rapidly. Comparison of results within methods showed the least variance for X-ray camera results; dilatometer and X-ray diffractometer results have about the same variance. The average deviations, in percent, between observed and calculated expansion values among methods were approximately 10 percent from 100°C. to 300°C., 5 percent from 300°C. to 500°C., and 2 percent from 500°C. to 1,400°C. Maximum deviations were approximately twice as large in most instances.

Jan 1, 1962

By D. C. McDonald

"IntroductionTHE GIANT YELLOWKNIFE property is on the west side of Yellowknife bay, Great Slave lake, N.W.T., some 600 air miles north of Edmonton. This paper deals with the underground development and mining of the complex system of orebodies which have produced, in the first fifty-six months of operation (May, 1948, to December, 1952), 652,464 tons of ore with an average grade of 0.80 ounces of •gold per ton (1).The mine has been developed from three vertical shafts designated A, B, and C. Figure l shows the positions of these openings with respect to the known ore-bearing zones and the surface plant.A shaft was sunk to a depth of 522 feet in 1945-46, primarily as a prospect shaft for investigation and development of the East Zone orebody. Drifting was carried out on the 200-and 325-foot levels. Before this development had been completed it was clear that the funds immediately available made it imperative to get revenue from production as soon as possible. By the beginning of 1946, the remarkably high-grade character of the ore in the present B Shaft area had been established by surface drilling, and the decision was made to obtain initial production from this source. Since known orebodies at shallow horizons were to be developed quickly, the choice of a suitable rock outcrop for the shaft was something of a problem."

Jan 1, 1953

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By J. Shahabpour

"Many porphyry copper deposits of the Kerman copper province in central Iran are associated with a consistent structurally con-trolled main drainage pattern, which is shown in this paper to be a useful regional prospecting tool in the search for new deposits. The main drainage trends also generally allow the distiction of high-grade (>0.2% Cu) from low-grade (<0.2% Cu) deposits. Topographic maps1:50 000 or geologic maps 1:100 000 have been found suitable for identification of promising drainages.IntroductionTrends of the main drainage systems transecting the high-grade porphyry copper deposits of the Kerman Region in Iran coincide with Quaternary age regional faults and fractures. Observation of such drainage trends can expedite regional evaluation prior to field examination. Thirty deposits located in the Kerman Region (Fig. 1) have been studied to identify common features that can be used for exploration purposes, especially for the first stage of regional exploration. A variety of field criteria are available for subsequent rapid field checking prior to trenching and more costly methods such as drilling, etc.Characteristic geomorphic features have been considered as aids in mineral exploration by many authors (e.g., Faniran, 1971; Piotrovski and Lubkashov, 1976; Verstappen, 1983). Clark et al. (1967) indicated the relationship between geomorphology and the supergene enrichment of copper in Atacama Desert, Chile, and correlated three periods of supergene enrichment with three periods of pediment disection. Seeland (1978) used fluvial drainage patterns for uranium and hydrocarbon exploration in the Wind River basin, Wyoming. Postolenko and Konopleva (1973) used the reconstruction of ancient valley systems for exploration of gold placers"

Jan 1, 1996

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By H. A. Dierks

The work and costs involved in controlling three large fires in abandoned mines in the anthracite region of Pennsylvania are presented in detail. The work was done under authority of Public Law 89-4. Three basic control techniques were successfully employed by the Bureau of Mines: (1) forming underground fire-containing barriers by systematically flushing incombustible material into mine voids, (2) excavating an isolation trench around the fire area, and (3) complete excavation of hot and burning material in the fire area. When methods 2 and 3 were used, the excavations were subsequently back- filled with incombustible material. Preliminary location of fire perimeters by the standard use of patterned 6- and 8-inch-diameter boreholes is discussed. Investigations into air-borne infrared scanning, shallow subsurface thermal anomalies, and the use of helium to trace the movement of mine air currents are covered. Although they are costly and time consuming, boreholes have proven to be the most efficient means to date of obtaining necessary subsurface fire data. Infrared scanning was ineffective in delineating fires under more than 30 feet of cover. Helium-tracing was shown to have a good potential for determining possible hazards to adjacent residential areas from traveling mine fire gases.

Jan 1, 1971

By James A. Clem

Approximately 2000 years ago, the Lord admonished the scribes (lawyers) and pharisees (religious leaders of that time) that they had paid the tithe but had omitted the weightier matters of law, judgment, mercy, and faith. (Matt. 23:23) I want to talk about "The Weightier Matters of Law." In a situation where big government is trying to have an effect on even small details of a work activity, otherwise simple situations become complex. Regulations are written to such detail that constant compliance with strict interpretations can be a nightmare-not to mention off the target of the intended purpose for the regulation. One soon recognizes the onerous characteristics of federal statutes. Another admonition the Lord gave those lawyers and pharisees back then was that they tended to strain at a gnat and swallow a camel! He meant that the pharisees were given to devoting themselves to the strict interpretation of law by writing hundreds of subrules or interpretation to law. In doing so they eventually lost sight of the original purpose of the law. I think they were being told, keep the law-but don&apos;t neglect to humanize it Keep it simple Recognize the purpose of why the law. "Mix in" a common sense approach. Someone once said, "Common sense is instinct -enough of it is genius." Today, as 2000 years ago, we need more "genius" displayed by legislators in considering the weightier matters of law. First of all true legislature genius calls for a declarative statement about the purpose of the statute and a fair, objective analysis of the ground rules by which it will be implemented. In the Health & Safety Act of 1969, the "findings and purpose" as set forth in Section 2 do define its purpose. I believe most of us affected can be in accord with the reasons advanced for the legislation. However, beyond those well-intentioned few paragraphs, we very quickly run into trouble. Congress complicated the simplicity of the statement of purpose by mandating government intervention into areas that cannot be effectively legislated, nor even should be legislated. The Act provided for broad gaged regulation which is unnecessary, inappropriate, and tremendously costly. Frankly, it detracts from a constructive, cooperative effort by the parties involved. These are strong negatives which characterize inappropriate legislation. Appropriate legislation and subsequent regulation, which is realistically conceived and practically enforced must be born of an honest desire for improvement, based on a working knowledge of common problems which are thoughtfully analyzed. Then the legislation must be written in clear concise language so that there can be little or no doubt as to its literal meaning and intent. To be practically enforced, it must be understood by all who will enforce it and by all who are subject to it. That is to say, an effective law or standard cannot be fixed or inflexible so that it cannot be tempered in human judgment. There must be an elasticity in the statute to provide for consideration of all of the relevant facts of a given situation. Such elasticity makes the compliance effort as meaningful as it can be for the time and dollars invested. Meaningful compliance requires room for common sense. Today, we in business along with our associates in government and labor, urgently need to pause, and assess our current situation. The problems arising from the 1969 Act have been intensified through the Mine Safety & Health Act of 1977. After reading the "findings and purpose" of this legislation, and by process of elimination, we should all clearly see what is and is not the purpose of the Act. 1) It is not to turn the management of private industry over to government. 2) It is not to impair the efficient operation of business. 3) It is not to reduce productivity and profits. 4) It is not to reduce national unemployment. 5) It is not to perpetuate the bureaucracy. 6) It is not to increase the tax burden on an already overburdened people. 7) It is not to increase our balance of payments deficit. 9) It is not to replace management/labor relations in working together to solve problems.

Jan 1, 1981

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By William B. Plank

NEVER before have so many men chosen the mineral technology field for their college training. In the college year 1936-&apos;37, 7190 such students were enrolled in the 53 schools of the United States. My last study of the mineral technology schools of the United States and Canada was made for the year -1934-&apos;35, and the current study, as the previous one was made for the A.I.M.E. under the auspices of the Division of Mineral Industry Education. Altogether, four studies of enrollment have been made. The first three were for successive college years beginning with 1932-&apos;33. This present one covers a two-year period, for the purpose of these studies may he served satisfactorily if they are made biannually. The data on the schools were collected in the same way as for former studies, &apos;namely, by questionnaire, dated in this case Nov. 18, 1936. The figures reported are therefore comparable with those of former cars.

Jan 1, 1937