Search Documents

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By M Sandy, P Bamford

The Challenger Gold deposit was discovered in 1995 by Dominion Mining Ltd in a remote western area of the Gawler Craton in South Australia. Mine development commenced in 2002 with initial production from an open pit supplemented by ore from a very small adjacent auxiliary pit. Development of the underground mine commenced in 2004. The orebody plunge of just less than 30 degrees requires careful attention to mine design. Production from the M1 orebody, with less than 800 ounces per vertical metre (ovm) and very limited æsurgeÆ capacity, requires careful scheduling and implementation to ensure continuity of ore feed for milling. Initial production results from underground stopes included more dilution than anticipated. The narrow, high-grade zones proved to have much more complex geometry than early interpretations had indicated. Greatly improved understanding of the mineralisation controls resulted in important changes being made to the underground mine design and method. Coupled with careful control of development and drilling and blasting practices, this resulted in an immediate reduction in dilution and high recoveries of the resource. The benefits of these changes flowed through in the 2005/06 financial year, resulting in a 150 per cent increase in gold production to 108 080 oz and a sharp reduction in cash operating costs to A$280/oz. This was followed in 2006/07 with production of 108 91 oz of gold at an operating cost of $309/oz and in 2007/08 with 109 326 oz of gold at $367/oz. Production to June 2008 has been mainly from the M1 orebody, with the lowest stoping to date on the 580 m Level (615 m below surface) above development mining on the 520 Level. The rate of vertical advance of mining this orebody has averaged 150 vertical metres per year. The increased current combined JORC compliant resource and reserve position of over one million ounces, now includes the M2 and M3 orebodies with a current total average gold inventory up to 1400 - 1500 ovm. Exploration has intersected other shoots and all shoots are open at depth. The adjacent M2 and M3 orebodies are being developed for stoping. The narrow width of these zones from 1 m up to 4 m will require continued focus on ore zone definition, accurate development and careful drill and blast practice. In addition, to minimise cost increases in the current period of rapidly escalating labour, equipment, consumables and energy costs, high productivities will need to be maintained to allow the established rapid mining advance to continue at low unit costs.

Jan 1, 2008

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

By A. Athousaki

The Ecological Footprint is a resource accounting tool used to address underlying sustainability questions. Aggregates consist of natural, artificial or recycled materials. The production of aggregates is the fastest growing activity worldwide since huge quantities are required by the construction industry. This paper presents a parametric investigation of the ecological footprint of transporting aggregates for urban use as a function of tonnage and distance.

Jan 1, 2008

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

By Hebi Yin

A two-dimensional finite element solidification model was developed to simulate the transport phenomena occurring during laser deposition of AISI 410 stainless steel during the Laser Engineered Net Shaping (LENS®) process. The molten pool geometry and the distribution of temperature, solute concentration and velocity were calculated during deposition of a thin wall plate. An analysis of the simulations results revealed the importance of heat transfer by both conduction and convection as well as the roles of the driving forces for convection in the molten pool. The heat transfer and the flow pattern in the molten pool are considerably dependent on the travel speed of the laser beam. For the alloy and process parameters in the simulations, no significant macrosegregation was observed. The temperature-dependent properties and thermodynamic variables involved in solidification modeling were calculated using Thermo-Calc software. The results of this work contribute to the current understanding of transport phenomena in the molten pool of laser deposition processes.

Jan 1, 2008

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By Viktor Ashikhin, Pavel Arkhipov, Yurii Zaikov

"Lead alloys electro-winning from chloride melts was under investigation. Impurities concentration in cathode lead is strongly depended on temperature, electrolyte composition, anode current density. The equilibrium electrode potentials of lead-antimony alloys with the various content of electropositive metal in the alloy were investigated in the wide temperature interval. Thermodynamic properties of Pb-Sb alloys containing 20-95 mol% of Pb were studied by EMF method in temperature interval 723-873K in molten mixture of potassium and lead chlorides. Partial and integral thermodynamic characteristics were calculated. Small negative deviations from Raul’s law were found. Anode processes were investigated. The lead dissolution was found to be the only process in certain interval of current densities and electropositive metal content in alloy.IntroductionAt present human race is facing the problem of pollution by lead and its compounds and also the pollution influence on population health all over the world. One of the solution ways is the recycling lead containing technical wastes by ecologically clean technologies.World scientific community pays much attention to the electrolysis of molten salts. The usage of salt mixtures, as electrolytes, discovers new possibilities in the production of metals, metal compounds and alloys. ?????????? of the electrolysis at the temperature 50 - 200 °? above the melting temperature of chosen salt mixture allow to unbreaks processes, that undergo in the pre-electrode layer. The rate of the electrodepositing of elements are much higher than in the water electrolytes. At present there are technologies developed for production of metals (Ta, Nb, Ti, Zr, Hf, Ca, Al, Mg, Be, Li and others) by the electrolysis of the melts. Electrolysis of melts might be used in order to convert different technological formations containing lead and other nonferrous metals, that produced by different enterprises. According to the level of the influence on the living organisms lead is in the group of highly dangerous substances alongside with arsenic, cadmium, mercury, selenium, zinc, etc. Toxity and ability to accumulate in the human organism are two main sources of danger for the human being."

Jan 1, 2008

By Alexandra Kozak, Rodrigo Costa, Bob Fukuhara

"The Jacobina project in Bahia, Brazil commenced operations in 2004 with a design capacity of 4,200 tpd. A project development plan to increase plant capacity to 6,500 tpd will be discussed. The project included an evaluation of the existing circuit and addressed bottlenecks in the crushing, milling, sedimentation, leaching and tailings transport. These circuits and the methodology used to provide higher capacity will be presented.INTRODUCTIONThe Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc.The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain.The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mine has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. The mine is currently owned by Yamana Gold Inc.In December of 1998, operations at Jacobina were suspended and the property was placed under care and maintenance. Desert Sun Mining Inc. began exploring the property in 2002 and eventually purchased the Jacobina mine in 2003. In 2003, a feasibility study was completed that evaluated the economics of re-developing the mining operations and expanding gold production. In 2004, refurbishment and re-development of the mining operations began and the milling facility throughput capacity was expanded from 1.08 to 1.512 Mtpy (3,000 to 4,200 tpd). The milling operations were commissioned in the 1st quarter of 2005 and commercial production was declared 1 July 2005. In April 2006, Yamana Gold Inc. acquired the Jacobina mine through its acquisition of Desert Sun Mining Inc."

Jan 1, 2008

By Andre Zingano

The objective of this paper is to study the effect of annulus thickness on the quality of resin mixture for fully grouted resin bolt. Pullout and mixture tests were made in underground coal mines for the following arrangements: (a) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with steel wire around the roof bolt; (b) borehole diameter 1.14 in. (29 mm), and roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt; and (c) borehole diameter 0.95 in. (24 mm) and a roof bolt diameter 0.75 in. (19 mm) with no wire around the roof bolt. The mixture test in steel pipe showed that the best resin mixture is for borehole with 0.95 in. (24 mm). The arrangement (b) produced big voids around the bolt. But for the 0.95 in. (24 mm) hole, arrangement c, the mixture was the best. It was corroborated with the pullout tests results where there is a difference in grout stiffness: the 0.95 in. (24 mm) borehole is about 10 times higher than a borehole with diameter 1.14 in. (29 mm). On the other hand, for the cohesive strength the difference is not significant. Numerical models were built to simulate the pullout tests, and also to simulate the roof support at an intersection. Convergence at two underground intersections, consisting of an immediate roof with laminated sandstone, was monitored to evaluate the performance of the roof supports, using the 1.14 and 0.95 in. (29 and 24 mm) diameter boreholes (i.e. arrangements ?a? and ?b?). The convergence readings showed that the 0.95 in. (24 mm) borehole diameter resulted in a smaller, although it was not significantly different.

Jan 1, 2008

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

By S Larbi-Bram, F Shi, E Manlapig

Mining companies have recognised that characterisation of particle breakage plays an essential role in the design and optimisation of comminution circuits. Recently the JKMRC comminution research team has developed a new breakage model incorporating the effect of particle size, and a new breakage characterisation testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions. The latter is believed to be the dominant breakage mechanism in AG/SAG mills. Existing devices, such as the JKMRC Drop Weight Tester, are not suitable for performing repetitive impacts since they are too time consuming. Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalised experimental test program on professionally designed and manufactured JKRBT machines. The first JKRBT was installed at the Anglo Research laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the project in 2008, with commercial release expected in early 2009. The JKRBT has the potential to revolutionise ore testing, with applications in laboratory impact breakage characterisation of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control of comminution circuits since it is readily adaptable to on-line ore hardness measurement. Can any mine afford to miss out on this technology?

Jan 1, 2008

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By J. Z. Cheng

The extraction of thorium from industrial radioactive wastewaters discharged from Rare Earth (RE) plants was studied by the liquid membrane emulsion technique using P507- Span80-sulphonating kerosene-HCl. The emulsion conditions, the technological factors such as ratios of oil to the internal aqueous phase and water to emulsion, and the extraction time etc. were investigated.

Jan 1, 2008

By C Caris, K Fowle, M Schmid, E van Wyk, D Schofield, A Squelch, M S. Kizil

This paper has been written collaboratively by members of the International Mining VR Group. It is the first of a series of papers. Mining in the 21st century is a high technology industry that strives to reduce risk and improve safety through the use of improved processes and procedures. This risk reduction process is aligned with the innovative use of technologies often developed for other industries. Computer-based visualisation systems and their content are such innovative technologies, in particular the use of virtual environment systems and mixed reality. A primary objective of developing virtual environment systems and the mixed reality content displayed in them for the mining industry is to allow mine workers and operators to practice mine processes and demonstrate competency in tasks that will be encountered in day-to-day mining operations at mine sites. It is anticipated that providing easy access to virtual environment systems will facilitate the avoidance of high-risk situations through improved knowledge, skills, understanding and decision making. Via virtual environment systems mine workers will also be able to practice infrequent or emergency events and maintain preparedness for such events. Day-to-day mining practices can also be evaluated. The rapid pace of technology innovation and the decreasing cost of simulation hardware and software present a plethora of technology to the uninitiated. This can be confusing. In this paper taxonomy is presented that classifies hardware, what it can display and also content that can be included or displayed on the various computer-based visualisation systems. The taxonomy provides insight into where technology can and may be implemented in the future as virtual environments are a dynamic and evolving technology. The taxonomy should also assist in the decision making process when scoping or selecting technology for a particular purpose.

Jan 1, 2008

By B Shen

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for approximately 14 km linking the Mt Thorley rail loop and the Wambo Coal Mine. The project involves a 260 m long tunnel in weathered sedimentary and intrusive materials. The tunnel has a low cover and runs under a main highway. This second paper on the project looks into one aspect of the tunnel in detail: the use of shotcrete arch as the primary support for part of the tunnel excavation. The use of shotcrete instead of steel arch, formulation of the material specification, construction sequencing, installation at the excavated face and material testing for verification related to this facet of the project will be discussed in this paper. The tunnel opened in April 2006, and two years on, we briefly reflect on the impact of this design decision on the overall project.

Jan 1, 2008

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008

By J. Greg Sanchez

The New South Ferry Terminal in the New York City Transit system represents an important milestone for the city. This is the first station designed and built in the 21st century. The design of the fire safety system included relying on Computational Fluid Dynamics to analyze the dispersion of heat and smoke, and modelling of people egress to determine the egress requirements. The project also looked into how to protect the structure from the heat exposure in order to meet the fire rating requirements. This paper provides an overview of the fire safety design approach taken to design the new South Ferry Terminal station in lower Manhattan and looks into fire modelling, structural fire protection, and station evacuation.

Jan 1, 2008