Search Documents

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By Paul L. Wichlacz

A mathematical model of growth and ferrous iron oxidation for attached bacteria was applied to rotating biological contactor (RBC) units treating acidic mine drainage. The model describes attached bacterial growth as a saturation function, where the rate of substrate utilization is determined by a maximum substrate oxidation rate constant, a half saturation constant, and the concentration of substrate within the RBC. The maximum oxidation rate constant was proportional to flow rate and the substrate concentration in the reactor varied with influent substrate concentration. The model was tested at three separate sites and with three different size RBC units. The ability of the model to predict the rate of iron oxidation under all test conditions was significant. The accuracy of the model was found to be affected by unit size and vary with specific test site.

Jan 1, 1985

By Hu Long

In this, the first systematic study of the oxidation of orpiment (As2S3) in sulfuric acid solution under oxygen pressure at temperatures above 170°C, the effects of retention time, temperature, particle size, oxygen partial pressure, the concentration of sulfuric acid and pulp density were evaluated. The effects of cupric and ferric ions on the oxidation rate of As(III) to As(V) were also examined. The products of oxidation are As(III), As(V), SO42- and elemental sulfur. At temperatures ranging from 170 to 230°C, most of the arsenic was found to be in the trivalent state, and oxidation to As(V) with oxygen was very slow. This was confirmed by attempting to oxidize a synthetic arsenious solution. However, the rate of oxidation of As(III) to As(V) is rapid in the presence of ferric ion. Elemental sulfur was found at all temperatures investigated, which can be further oxidized to sulfate at high temperature.

Jan 1, 1999

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By W. Kunda

A laboratory study was carried out on the treatment of sulphidic copper concentrates in aqueous chloride systems under elevated temperatures and oxygen overpressure. Exploratory tests showed that chalcopyriteoxidizes with various chloride salts to form, depending upon the pH of the system, soluble copper chloride or insoluble copper oxychloride salts; the copper can then readily be recovered from the solution or residues respectively. During the leaching, iron was oxidized to iron oxide and remained in the leach residue while the bulk of the sulphide sulphur was oxidized to the elemental form with a minor portion oxidized further to sulphate. The presence of metal chloride salts in the system increased the oxidation rates of chalcopyrite and depressed the solubilization of iron in the system. A systematic oxidation leach study carried out in (1) ammonium chloride and (2) sodium chloride systems showed that the former system required little or no HC1 addition while the latter required 2 mol of HC1 per mol of dissolved copper (plus zinc). The copper was recovered from the cuprous or cupric chloride leach solutions by cementation with iron. Extractions of 99% copper and zinc, 97% silver, and negligible iron were obtained. Sulphur was oxidized to the elemental or sulphate form; the relative proportions of the total sulphur were 60 and 30% for system (1) and 80 and 10% for system (2). A flowsheet for a conceptual process with minimal reagent requirements was proposed.

Jan 1, 1976

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By Ángel Ruiz-Sánchez

Ethylene glycol additions to aqueous acid solutions for leaching copper sulfides increase both copper and iron extractions compared to a conventional sulfuric acid leach with hydrogen peroxide (H2O2). The role of ethylene glycol is to prevent peroxide destruction, which normally occurs in solutions that contain both cupric and ferric ions. However, despite this improvement, ethylene glycol and sulfuric acid concentrations must be high (3.5 M and 0.7 M, respectively) to obtain satisfactory conversion levels at room temperature. In the present investigation, EDTA was used as an additive to complex the cupric and ferrous ions, lowering the requirements of ethylene glycol and H2SO4 to 0.11 M and 0.007 M, respectively, while minimizing oxidant decomposition. The experimental results for a mainly chalcopyrite, copper concentrate showed complete copper extraction in 24 h at room temperature, with the stoichiometric quantity of EDTA for the copper and iron dissolved. Tests using seawater were equally as successful.

By Lloyd R. Nelson

Selective carbothermic reduction is the preferred method of treatment of electric arc furnace (EAF) dust (listed hazardous waste, K061). The process maximizes the recovery of recyclable constituents by concurrent production of saleable zinc metal (directly condensed from the furnace off-gases), an innocuous, disposable iron oxide-rich slag, and some metallic iron. Results of a mineralogical investigation of a foaming slag produced during selective carbothermic reduction treatment of EAF dusts are presented. Wiistite and tricalcium silicate were identified by reflected light microscopy as the primary crystalline phases contained in a glassy matrix, but this technique failed to reveal any solid phases that could have significantly contributed to foam stability. It was concluded therefore, that the foam had been unstable, and had been primarily generated by copious gas evolution associated with the sudden reduction of the slag by an inadvertent addition of carbonaceous reductant. This is consistent with the susceptibility to foaming, when subjected to sudden excesses of carbon, of the slags produced by selective carbothermic reduction, because they still contain unreduced components such as iron oxide.

Jan 1, 1994

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

By James E. Hoffmann

Oxidative pressure leaching is gradually supplanting other techniques for the decopperizing of slimes. The reasons for this include: much more rapid reactions, more compact equipment, a reduced environmental burden, and perhaps most important, a much lower final copper concentration in the decopperized slimes. This paper will discuss the reactions occurring during decopperization, the acidity and temperatures encountered and the techniques employed for discharging non condensable gasses. A spreadsheet is provided which allows adjusting the operating conditions depending upon raw (undecopperized) slimes composition, solids concentration and lixiviant composition. A typical process equipment flowsheet is provided along with a process narrative.

Jan 1, 2000

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By Rodney Hundermark

At Anglo American Platinum’s Polokwane Smelter, radar instruments are being used to provide continuous measurement of the concentrate feed level in the six-in-line electric furnace used for smelting of nickel-copper concentrates containing platinum group metals (PGMs). The radar instruments are installed directly on the furnace roof, and a mechanical system has been designed to protect them from radiation and elevated freeboard temperatures and pressures. Signal validation criteria have been implemented to ensure that proper level measurements are being used by the PLC system. The feedback from the radars has provided an improved understanding of the furnace behaviour with respect to concentrate feed level control, individual feeding events, global feed rates, feed distribution and bath disturbances. In combination with a dynamic mass balance for continuous calculation of liquid level in the furnace, the radar measurements have enabled more precise feedback control of the concentrate blacktop depth. In turn this has yielded improvements in furnace stability.

By Paul O. Malan

"The Tusc gold deposit is located along the Carlin Trend approximately 13 kilometers north of Carlin, Nevada and 2.5 kilometers northwest of the Gold Quarry mine. Tusc is one of several structurally controlled oxide gold deposits located along the Good Hope fault within the Maggie Creek subdistrict. Mining commenced in 1994 with an oxide reserve of780,000 troy ounces of gold at an average grade of 1.34 g/t Au. The Good Hope fault forms the southwestern edge of the Schroeder Mountain uplift (also known as the Carlin Window) and juxtaposes carbonate rocks of the Siluro-Devonian Roberts Mountains Formation against siliceous mudstone, siltstone, and silty limestone of the Devonian Rodeo Creek unit. Submicroscopic gold mineralization is disseminated in the Good Hope fault system and in fractured hanging wall carbonate rocks. Wallrock alteration includes silicification, deca!cification, sericitization, and late alunite replacement and veins. All Tusc ore is transported 2.5 kilometers to Gold Quarry for processing. Leach-grade ore (0.2 - 1.7 g/t gold) is placed on the oxide leach pads, and mill-grade ore(> 1.7 g/t gold) is processed through the CIL oxide mill. IntroductionThe Tusc gold deposit is located in Eureka County, Nevada, U.S. A, approximately 13 kilometers north of the town of Carlin and 2.5 kilometers northwest of the Gold Quarry mine (Fig. 1 ). Tusc is one of several open-pit, oxide, gold deposits within the Maggie Creek subdistrict of the Carlin Trend. Tusc is a structurally controlled gold deposit located along the Good Hope fault. Submicroscopic gold mineralization is disseminated in the brecciated and silicified Good Hope fault zone and along intersecting northeast and northwest striking structures."

Jan 1, 1997

By Eva B. Kisvarsanyi

An Early Proterozoic orogenic terrane of metasedimentary and metaigneous rocks underlies Nebraska, Kansas, and Missouri. Middle Proterozoic epizonal terranes of anorogenic granite and rhyolite, a known metallogenic province partly exposed in southeastern Missouri, overlap the orogenic terrane on the south. These Proterozoic terranes, covered by less than 1,000 meters of Phanerozoic strata, contain a virtually untapped source of mineral wealth and are one of the last frontiers for geologic exploration in the continen-tal United States. Petrographic study of subsurface samples is a powerful tool in the identification of favorable host rocks for a variety of ore deposits.

Jan 1, 1987

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003