Search Documents

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

By E. J. Matson

From February until July 1943 the Bureau of Mines conducted an exploration project at the Majuba Hill mine to determine tonnage aria grade of the copper and tin ore and to search for extension of the mineralization. The work comprised sampling, long-hole drilling, underground excavation, and ore-dressing test.

Jan 1, 1948

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

By S. P. Kinney

The Department of the Interior has recently investigated the atmospheric conditions in tunnels of the Union Pacific Railroad in Utah and Wyoming , by observations made from the cabs of freight locomotives . This work was conducted by the Bureau of Mines at the request of , and in cooperation with , the Union Pacific Railroad Co .. and was brought about by several accidents to members of engine crews while passing through tunnels , from pollution of the tunnel air by exhaust gases from freight locomotives . The object was to determine the cause of gassing accidents , by examining into composition of the air in locomotive cabs while passing through railroad turmels ; to learn the effect of these conditions on the engine crew; and to provide a means of protection for the men so exposed . Gas samples and temperature readings taken in the cabs of locomotives were used in studying the atmospheric conditions to which the locomotive crews were exposed . The symptoms and the physiologica effects produced in men exposed to the atmospheres encountered were studied . The pulse rates and body temperatures were taken , and the determinations of the carbon monoxide content of the blood were made . Various methods for the prevention of gassing and for the protection of men therefrom were considered and tested , among which were the use of mechanical devices for deflecting the smoke away from the engine cab, and the use of various types of gas masks and breathing apparatus . While this investigation is a part of the safety work of the Bureau of Mines in connection with hazards from atmospheres containing carbon monoxide ( CO ) , the results are of particular value to railroads operating steam locomotives through tunnels , and are also valuable to other industries where atmospheres having poisonous gases or of a high temperature and humidity may be present . The results may be summarized as follows :

Jun 1, 1923

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By Douglas C. Corner

This is the first of a series of papers dealing with modern tunnel-driving methods, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines and to be published in a series of information circulars by the bureau. This series will supplement a similar and earlier series of papers dealing with mining methods and costs. ACKNOWLEDGMENTS The author desires to express hiss appreciation, of the assistance of A. C. Dennis, manager for the West Construction Co. Contractors, and Franc: E. Winsor, chief engineer for the Boston Metropolitan District mater Supply Commission who furnished much of the data and detailed description of operation appearing in the following pages. C. F, Jackson, mining engineer, United States Bureau of Mines, collaborated in the preparation and arrangement of the text.

Jan 1, 1931

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

By N. Greninger

The Bureau of Mines conducted a laboratory study of the measurement of the water and rock dust (RD) contents of synthetic mine-type coal dust (CD) mixtures using a commercial unit for measuring water content and several prototype radiometric units for measuring the RD content. The RD content ranged from 50 to 100 wt pct and the added water (AW) ranged from 0 to 15 wt pct. The total water (TW) content (intrinsic (IW) and AW) of a small dust sample could be readily measured automatically by essentially untrained personnel using a commercial unit. The RD content of a sample containing only IW could readily be measured by moderately trained personnel using several radiometric units. With gamma-ray devices, about 300 g of sample is needed. With the improved beta-ray device, about 25 g of sample is needed. With dry mine dust samples, the estimated RD error range for gamma-ray devices is 0.8 to 2.3 pct and 0.5 to 1.0 pct for beta-ray devices. However, the radiometric measurement of RD content was questionable if the dust mixture also contained AW or if it was uncertain whether the dust mixture contained AW.

Jan 1, 1988

By M. Hayashi

The Bureau of Mines conducted laboratory studies on low-grade vanadiferous silicates from the Pumpkin Buttes and Nine Mile Lake deposits of Wyoming to examine techniques for extracting vanadium and uranium. Recovery from low-grade sources such as these could contribute to future vanadium production and reduce reliance on vanadium imports. The Pumpkin Buttes samples contained 0.03 to 0.04 pct V205 and 0.06 to 0.12 pct U308; the Nine Mile Lake samples contained 0.02 to 1.0 pct V205 and 0.06 to 0.19 pct U308" Leaching the Pumpkin Buttes samples for 18 h at 800 C with addition of 200 lb/ton H2S04 resulted in recoverey of 80 pct of the vanadium contained in the samples. The Nine Mile Lake samples were readily leached, yielding 78 to 94 pct of the vanadium after 3 h at 800 C with addition of 100 lb/ton H2S04, A solvent extraction procedure was used to selectively recover urani-um from Pumpkin Buttes and Nine Mile Lake leach solutions and to recover vanadium from the raffinates. In batch shakeout tests, Alamine 336 recovered over 95 pct of the uranium from leach solution adjusted to pH 1. Di-2-ethylhexyl phosphoric acid and Cyanex 272 recovered vanadium from the uranium raffinate after reduction and adjustment to pH 2; vanadium extractions of up to 96 pet and 92 pct, respectively, were achieved.

Jan 1, 1985

By Douglas F. Scott

Researchers from the U.S. Bureau of Mines conducted geologic investigations in an area of the Lucky Friday Mine, Mullan, ID, that included the 5300-107 demonstration stope using underhand longwall cut-and-fill mining. Structural analysis of the area suggested that argillite beds form planes of weakness between blocks of brittle quartzite, and energy may be released along these planes and at the junctures of fractures. Mapping argillite beds and fractures in the stope wall rock showed that the planes of these features diverged and that their attitudes corresponded from one wall to the other. Seismic analysis showed that the number and location of events varied as each cut was mined, with about 39 pct of the total number of events occurring above the cut being mined, about 54 pct below, and 7 pct at the same elevation.

Jan 1, 2010

By J. M. Singer

Flame propagation of lower limit hybrid coal dust-methane-air mixtures in vertical and horizontal flame ducts of 15.2 cm id and 1.8 m length has been investigated to provide information bearing on safety in mines. Fuel concentrations at lower limits of flame propagation and equivalences of coal dust and methane are much higher for continuing flame propagation than for short-span flame propagation in the vicinity of an "overdriving" ignition source. As the energy of the ignition source was increased, the flame speed and the distance of flame propagation from the ignition source increased, whereas the total fuel concentration at the lower limit decreased.

Jan 1, 1968

By Berk. A. A.

"INTRODUCTION Corrosion of sections of piping used in steam-heating systems is frequently regarded as unavoidable, and periodic replacement is provided. Surfaces exposed to newly condensed steam appear to be especially vulnerable to attack. As an added nuisance, solid products of the corrosion tend to accumulate, plugging return lines.The trouble is ascribed in the main to carbon dioxide and oxygen 3/ 4 / 5/ 6/ dissolved in the condensate. When oxygen is the principal factor, the corrosion usually is characterized by pitting. Carbon dioxide tend3 to cause an acidic condensate which dissolves the metal more uniformly and produces the familiar failure at threaded areas where the piping is relatively thin, and where high stress may tend to acceletate the attack. Carbon dioxide enters the system with the feedwater, generally in a combined form such as carbonates and bicarbonates. Oxygen enters both with the raw feedwater-and as air leaking into lines under partial vacuum. The larger central-heating plants have sought to reduce corrosion by eliminating these gases as much as possible. A smaller plant ordinarily lacks the equipment and technical supervision required for this purpose."

Jun 1, 1944

By R. C. Hickman

"INTRODUCTION The largest known deposits of ilmenite and rutile in Virginia are in Amherst and Nelson Counties. Other deposits occur in the State, but their extent is not known. One of the most promising of the latter is the deposit in Roanoke County on the T. M. Bush and the H. L. Hutchins property near Roanoke. A geophysical survey was made of the deposit, followed by core drilling. In April and May 1946, four holes were drilled, totaling 822 linear feet.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch,. Bureau of Mines."

Aug 1, 1947

By Graham W. Marks

This report is the fourth of a series concerning the development of spectrochemical methods for the analysis of ore samples and related Metallurgical materials by the total-energy method. In this report, the application of this method to the determination of thallium is discussed. This element lies in group III of the periodic tale; one other Clement of this group; indium, has already been investigated.

Jan 1, 1949

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By P. D. Laverty

The U.S. Bureau of Mines treated mixed and contaminated super alloy scrap by pyrometallurgical and hydrometallurgical methods to separate and recover metal values. Best results were obtained by leaching Zn-treated or atomized scrap with HCI-02 at 9SO C and 50 psig 02' This resulted in dissolving approxi-mately 98 pet of the AI, Co, Cr, Cu, Fe, Mn, Ni, and Zn while rejecting over 98 pct of the Mo, Nb, Ta, Ti, W, and Zr as an insoluble refractory residue. Chlorine was successfully substituted for HCI to leach Zn-treated scrap but was unsuccessful for leaching atomized scrap. The leaching solution was treated by pH adjustment and hydrothermal precipitation at 2000 C for 4 h to remove AI, Cr, Fe, and other contaminants as a filterable precipitate. Recovery of Co and Ni would be accomplished by solvent extraction and e1ectrowinning. Chromium recovery as a ferroalloy was demonstrated.

Jan 1, 1989

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011