Search Documents

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By E. W. Dean

In the early winter of 1919 the Pittsburgh petroleum laboratory of the Bureau of Mines undertook the work of testing fuel oil samples representing purchases of the United State Shipping Board for ships sailing from the port of New York. fuel oil was, at this time, being bought on a contract which involved specifications issued by the United States Navy under dace of October 2, 1920 (See Bulletin 1, Oil Division, U. S. Fuel Administration.)The object of the Bureau of Mines in undertaking this inspection work was twofold. (1) The Bureau was in position to give, and the Shipping Board needed, reliable laboratory service for checking the quality of the fuel oil purchased, the value of which ran into millions of dollars for,year's supply. (2) It was believed, and later demonstrated, that the existing specifications did not insure the obtaining of a reliably satisfactory quality of oil.The objection to the specifications concerned the employment of a clause limiting the gravity of the oil. The inadequacy of gravity specifications for several types of petroleum products has long been recognized, and there was every reason to reason to believe that they were no more desirable for fuel oil than for gasoline, kerosene, or lubricating oil. A first and obvious objection was the fact that it is somewhat difficult to make accurate gravity tests on ""heavy"" residuum fuel oils. (The Bureau found it necessary to employ or such tests a rather tedious procedure involving the use of a picnometer and an accurate balance, as the simpler methods, employing hydrometer or displacement balance, proved unreliable in a large proportion of cases.) A second and more important objection was that gravity tests, even when accurately made, do not provide a reliable index of the actual quality of the oil.

Feb 1, 1921

By J. A. L. Henderson

THE potential oil-and gas-bearing area with "which this paper deals is the large undefined Carboniferous basin, roughly triangular in shape, occupying about 10,000 square miles of southern and eastern New Brunswick. Its base, about 135 miles long, lies on the gulf of St. Lawrence and embraces the whole eastern coast-line of the Province, while its apex lies in the south-west corner of the Province, near the International boundary (see map, Figure 1). The Carboniferous basin may be divided roughly into two areas-the Northern basin and the Southern basin-by a structural feature represented by a ridge of low hills running north-easterly from the Saint John river, near Saint John, on the southwest, to Indian mountain, about eight miles north of Moncton, in the northeast. Within the Northern basin, all evidence regarding the presence or attitude of the older Mississippian Albert Shale series, the only oil-bearing rocks known in New Brunswick, is for the greater part obscured by a thick and practically horizontal blanket of Pennsylvanian strata and, although evidences of oil and gas have been reported, none has been positively identified. Five parallellines of gentle folding, running to the northeast, occur in the Pennsylvanian rocks, within a distance of 100 miles from north to south. This folding is reflected in the courses of the rivers, which lie within the synclines. The relationship of the folding in the younger rocks to structures in the uncomfortably underlying older rocks is unknown, but should now be possible of clarification by means of a geophysical survey accompanied by drilling. Independent geological examinations have yielded no evidence of value in this respect, nor have five exploratory boreholes drilled by per-cussion tools to a maximum depth of 3,645 feet been of assistance, as only one inconclusive hole completely traversed the beds which normally overlie the Albert shales.

Jan 1, 1940

By J. Hupka

The limited effectiveness of the original hot water process for recovery of bitumen from certain Utah tar sands containing bitumen of higher viscosity (e.g. Sunnyside, Tar Sand Triangle)1,2 indicated that bitumen viscosity strongly' influences the separation efficiency. In this regard, there should exist a critical value of bitumen viscosity above which the effectiveness of the hot water process decreases significantly. Apparently certain tar sands contain bitumen of such high viscosity that even a digestion temperature of nearly 100°C is insufficient to lower the viscosity below the critical value. In addition it seems that differences in physico-chemical forces which act between sand and bitumen are negligible in comparison to the difference in visco-mechanical forces. Predominantly mechanical forces hold viscous bitumen on the rough surface and in the pores of sand particles, resulting in strong adhesion. This phenomenon is a critical feature in the phase disengagment of oil-wetted domestic tar sands with viscosity control by temperature. Besides increasing the temperature for viscosity control the effectiveness of the original hot water process could be enhanced by control of bitumen viscosity with diluent additions. Strictly speaking this appraoch is the only possibility for heavy bitumen for which the high temperature of digestion does not lower the viscosity sufficiently. As a result of viscosity control by diluent addition the digestion temperature can be lowered which is important from an industrial standpoint. Another important consideration is that effective phase disengagement occurs only when the entire bitumen phase has the same viscosity. This means that some time (penetration time) is necessary for complete and uniform dilution of the bitumen. If the viscosity of bitumen, which is a function of temperature, diluent addition and penetration time, controls the separation efficiency, hot water processing of many different kinds of tar sands should be possible, assuming that the sand phase consists primarily of quartz-type minerals.

Jan 1, 1982

By Weller KR

A study of high pressure rolls grinding of a number of Australian ores and minerals has been carried out using a pilot-scale machine with rolls 300 mm diameter and 70 mm wide. The results from this study have been used in conjunction with plant survey data to construct computer simulation models of various comminution circuits and these have been used to investigate options for incorporating high pressure grinding rolls into these comminution circuits. Possible rolls options for three of these circuits are presented, and likely energy savings over the existing circuits are discussed together with potential improvements in plant throughput and/or product sizing. A scale-up procedure for predicting full-scale machine performance from small-scale testing is described, and the effects of rolls operating conditions are also discussed.

Jan 1, 1991

By Richards J. W.

J.W. RICHARDS, South Bethlehem, Pa. (communication to the Secretary?).-Mr. Howland's paper, data and conclusions have interested me intensely, and have led me to study carefully the record-of his 26 furnaces therein given. Mr. Howland is undoubtedly right in his conclusion that when expressing the amount of carbon burned at the tuyères in percentage of the total

Jan 1, 1917

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By A. C. Fieldner, SIDNEY GOTTLIEB

This report summarizes the research and technologic work of the Bureau of Mines on coal and coal products from July 1, 1947, to July 1, 1948. It is the thirteenth of a series presenting resumes based largely upon publications issued during the year . In some instances , research and testing results , not otherwise available in published form , are presented . The individual publications given as footnote references herein will provide further detail to the interested reader . The period covered by this report was marked by an ever -mounting concern for the adequacy of the Nation's fuel resources and for fuel shortages arising from an increasing demand for fuels at home and abroad . Several reports appeared which delineated the place of synthetic liquid fuels in the future fuel technology and economy of the Nation , emphasized the fact that eventually the principal raw material for the production of such fuels will bet,5,6 coal, and described the progress made by the Bureau of Mines in developing processes for the production of synthetic liquid fuels . heard testimony along similar lines . Increased awareness of the fuels problems confronting the Nation led to an authorization by the 80th Congress for the erection of an anthracite research laboratory at Schuylkill Haven , Pa . , to house expanded Bureau of Mines research on anthracite . Design of the structure was well under way by the end of the fiscal year . ( See fig . 1. ) Looking forward to expansion of Bureau research on lignite , the 80th Congress heard testimony on the problems and programs of lignite research10, 11 as a prelude to authorizing the construction of a lignite research laboratory in North Dakota .

Aug 1, 1949

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987

By G. R. Speich

The age-hardening of Fe-18 to 21 pct Ni marten-sites containing small amounts of titanium, aluminum, copper, or molybdenum has been studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electyon-probe microanaly-sis of the extracted precipitates was also performed. The effects of temperature and composition on the aging kinetics have been studied in detail for Fe-20 pctNi-Ti martensites. All the martensites hardened on aging at 400" to 500 "C with a single aging peak. In the Fe-20 pct Ni-Ti martensites hardening was associated with the formation of a fine dispersion of NisTi. No precipitation was observed in an Fe-21 pct Ni-2.6 pct A1 alloy, although the hardness increased from 327 to 545 Dph during aging at 500°C. Copper was precgitated from an Fe-20 pct Ni-10.7pct Cu alloy, at least during the later stages of age-hardening. Hardening in an Fe-18 pctNi-5pct Mo alloy was associated with the precipitation of an intemzetallic compound tentatively identified as NisMo. The formation of austenite and the recovery of the defect structure of the martensite occur simultaneously with the normal precipitation processes &ring aging of these alloys. THE age-hardening of substitutional iron-base martensites is an important subject for study since age-hardening is one of the principal means of strengthening the substitutional iron-base martensites in precipitation-hardening stainless steels1 and maraging steels.a~4 In contrast to Fe-C martensites, these martensites are relatively soft and ductile in the as-quenched condition, due to the low solid-solution hardening effect of the substitutional elements as compared to carbon. Also, these martensites are hardened by aging at low temperatures in contrast to Fe-C martensites which generally soften on tempering. Titanium and aluminum, singly or in combination, as well as copper and molybdenum, have been the principal alloying additions to stainless steels to obtain an age-hardening reaction.' Ti-A1 or Co-Mo-Ti combinations have been used in the case of maraging steels.3"4 The present work has been confined to a study of the age-hardening characteristics of an Fe-18 to 21 pct Ni martensite to which small amounts of titanium, aluminum, copper, and molybdenum were added in order to study the effects of each alloying element separately. The age-hardening characteristics of these alloys were studied by hardness measurements, transmission electron microscopy, extraction replicas, and X-ray and electron diffraction. Electron-probe micro-analysis of the extracted precipitates was also performed. The types and dispersion of precipitates, the formation of austenite, and the recovery of the defect structure of the martensite all were studied. EXPERIMENTAL PROCEDURE Alloys. The compositions of the alloys studied are listed in Table I. The level of 18 to 21 pct Ni was chosen to assure complete transformation to martensite on quenching and is the same nickel level used in maraging steels. The concentrations of titanium, aluminum, copper, and molybdenum were chosen after a study of the and Fe-Ni-MO' ternary diagrams indicated how much of each alloying element could be dissolved in austenite. Alloys with 2 and 4 pct Cu were also studied, but these did not show precipitation hardening at the nickel levels studied and will not be discussed further. The alloys were prepared from electrolytic iron and high-purity* nickel, titanium, aluminum, copper, and molybdenum by vacuum melting of 20-lb heats. These were vacuum-cast into two 8-lb ingots. The ingots were hot-rolled at 1100°C to 1/2-in. plate and subsequently cut into 3/8-in. cubes. The cubes were sealed in evacuated quartz capsules and solution-treated for 16 hr at 1100°C, except for the Fe-20 pct Ni-10.7 pct Cu alloy and Fe-21 pct Ni-2.6 pct A1 alloys which were solution-treated for 16 hr at 1300" and at 1250"C, respectively. Metallographic examina-

Jan 1, 1963

By Thomas B. Borak, Keith J. Schiager, Janet A. Johnson

OBJECTIVES OF RADIATION MONITORING Monitoring is a tool used in the practice of radiation protection. The primary reasons for monitoring are to reduce radiation exposures to levels that are as low as reasonably achievable and to assure that no individual receives a dose exceeding the maximum individual dose limit. The documentation of radiation doses for legal, medical, or epidemiological reasons is a subordinate function of any monitoring program. The investment in radiation monitoring programs should be guided by four criteria: (1) the detection and avoidance of unnecessary exposures, (2) the magnitude of potential health risks, (3) the determination of combined doses and risks with adequate confidence, and (4) the verification of compliance with established limits. FIRST CRITERION: DOSE REDUCTION - DETECT AND CORRECT UNNECESSARY EXPOSURES The system of dose limitation advocated by the International Commission on Radiological Protection (ICRP, 1977), and subscribed to in a broad sense by various regulatory agencies, is comprised of three essential ingredients: (1) [justification] of any practice that produces radiation doses by some commensurate net benefit, (2) [optimization] of radiation control measures by reducing doses to levels that are as low as reasonably achievable, and (3) [limitation] of individual doses to preclude inequities and [moldistribution] of risks. All too often, only the third criterion - the limitation of individual doses to prescribed regulatory limits - is explicitly addressed in everyday radiation protection programs. The emphasis of most exposure control and monitoring efforts appears to be directed toward limiting and documenting individual doses that might approach the legal limit. The first two criteria, i.e. justification and optimization, should contribute to a rationale for allocating monitoring efforts. When applied to individuals, these criteria mean the detection and elimination of unnecessary exposures. This should be a high priority of any monitoring program. Measurements should be directed toward detecting inoperative or ineffective control measures, whether or not there is a risk of exceeding the individual dose limits. The ICRP recommends a procedure that can be used effectively to reduce unnecessary exposures. A n investigation level should be established at an exposure rate substantially lower than the regulatory limit, e.g. 30% of the limit (ICRP 26, 1977, p.33). Measurements obtained during routine monitoring that exceed the investigation level are evaluated with respect to cause and potential reduction. To be effective, the evaluation results should be formally recorded and conveyed both to management and to the workers involved. Although the investigation level recommended by the ICRP is based on a fixed exposure rate or derived air concentration, an equally effective evaluation program may be based on the investigation of a percentage of all measurements. For example, one might investigate the highest 5% or a random selection of all measurements. In any case, the objective is to detect and correct situations that are producing unnecessary exposures. SECOND CRITERION: MONITOR IN PROPORTION TO THE MAGNITUDE OF RISK The ICRP criteria apply generally to all radiation exposures. However, a second priority for monitoring programs should be established on the basis of the nature of the exposures and the magnitude of the health risks involved. Current practices in radiation protection are based on dose limits to specific organs and assessment of individual exposure pathways, with little consideration of the combined doses from various pathways. Although the intent of the ICRP recommendations was to limit the total dose to each critical organ, combined doses from external and internal sources are rarely determined. The recent recommendations of the ICRP (Publ. 26, 1977) are based on the limitation of total health risk from occupational radiation exposures. Implementation of this concept would necessarily require the measurement, calculation and summation of doses and concomitant risks to all organs of the body from all exposure pathways. The U.S. Environmental Protection Agency has taken the first step toward translating the ICRP recommendations into regulations. The proposed recommendations for Federal Radiation Protection Guidance for Occupational Exposures (USEPA, 1981) include provisions for summing the risk-weighted organ doses to determine compliance with an effective whole-body dose equivalent limit. Whether or not the proposed guidance is modified before final adoption, it seems clear that some version of dose summation and combined risk limitation will be included in future regulations. With this

Jan 1, 1981

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By B. Arlyuk

The complex system has been developed for long-term assessment of world prices and sale volume of primary aluminium when using the analytical model of the market and market supply forecasts as well as economy development in the Western countries characterized by the industrial production indices as correct data of Western World aluminium consumption are absent, The important part of this system is the model developed for forecasting the degree of capacities utilization of smelters and refineries depending on the price level, The model contains a statistic part corresponding to the capacities distribution by the production cost, and a dynamic part determining the deviation from the static depending on the price variation dynamics, The developed complex system has been identified by the actual data of the world prices of smelter grade alumina and primary aluminium, conservation and reactivation of refineries and smelters in the Western countries within the period from 1992 to 2003. The system was used for primary aluminium and alumina price forecasts till 2020.

Jan 1, 2004

By H. M. Garrett

Dr. Ft: L. Handy of Iowa State University's Engineering Experiment Station very handily reduced the relatively complex cement making process to ultimate simplicity: "Take two cups of crushed limestone; add one-half cup of clay or pulverized shale (plus perhaps some sandstone or iron ore; depending); mix thoroughly and grind up fine. Bake in white-hot oven at about 2,600 F. Cool. Add a tablespoon of gypsum: and, again, grind very fine. If you can do this for about a penny a pound, you can almost compete.' Before Dr. Handy's time, is the early days of the U. S. Cement Industry, from 1817 when the Erie Canal was started to 1895 when the first rotary kiln was built, this was the recipe, more or less. Dr. Handy's raw materials were deposited in a natural "cement rock" found in the Hudson, New York and Lehigh, Pennsylvania valleys. At first the natural rock was pulverized (not ground fine) and interlayed with wood for "baking" at about 1,800° F in a batch process vertical shaft kiln or beehive oven; then the calcined pozzalonic (lime and silica) product was cooled and ground fine for shipment in wooden barrels. Later, in 1871, true portland cement was made. The same natural rock was ground fine to make briquettes; interlaced with wood or coal in the "Beehives"; and baked at a clinkering temperature of about 2,6000 F to produce clinker (calcium silicates) which was ground fine for sale. In those days, the crude cements dropped in price from over 1 cent to 1/2 cent per pound. In 1895 the rotary kiln introduced-continuous instead of batch processing. The countercurrent process allowed the same raw materials (now finely ground to about 80% minus 200 mesh like face powder) to be fed at one end of the rotary kiln. Heat from a coal burner was introduced with combustion air at the other end to produce the requisite clinkering temperature. The clinker product was discharged for atmospheric cooling, mixed with gypsum, and again ground fine as face powder. The cement was sold primarily in barrels, later in jute or cloth bags, then paper bags, and now primarily in bulk truck and barge carriers. The price dropped to a 1/4 cent per pound by 1910, but with recent inflation it now sells for 2 cents per pound.

Jan 1, 1978

By Thierry Bernard, Philippe Dozohne

May 13th, in the back country of Nice @arice) collapsed a complete piece of mountain, cutting the RN 2085 and destroying a part of Valabfre’s viaduct. The fist inspections of the site showed that materials had broken loose from surrounding cliffs, The geologists discovered that a block of several thousands of m3 remained suspended in cliff and that it presented a risk raised of gliding. Decision to destroy it by blasting in one blast was there taken by the French department’s council of the Maritime Alps. A race against the clock engaged. Indeed, the RN on 2085 is the main axis connecting the village of Saint Etienne de Tinee and the resort station of ISOLA in the centre of Nice

Jan 1, 2001

By George C. Branner

This Bureau of Mines report presents information on the origin, collection, movement, and consumption of iron and steel scrap in California and Nevada. As far as practicable, information is presented on a grade basis. The iron and steel scrap industry in California is important from the standpoint of employment, economic essentiality, and dollar value. About 16,000 persons are either directly or indirectly employed on a full- or part- time basis in the collection, preparation, and sale of iron and steel scrap in California; in 1957 about 70 percent of the tonnage of products of California steel mills, valued at $271 million, was derived from scrap; the value of scrap in 1957 ($117 million) is about $10 million greater than the value of portland cement produced in California that year. The iron and steel scrap industry in Nevada is small.

Jan 1, 1960

By D. Harrington

The placing of much, sometimes practically all, of the burden of the expense of mine accidents on the shoulders of the mine operator by compensation laws, and the fact that the problem of protecting the life end limb of workers is now by public opinion largely if not wholly passed to each industry to solve (and present-day thought strongly supports the justice of both of these propositions), are forcing industrial organizations into accident-prevention. Work. This policy is being adopted not alone to protect the companies; in addition, executives alert to their opportunities and obligations are taking part in this work personally to protect themselves. The functions of industrial executives in accident-prevention work are becoming numerous and complex. Executives who are logical in their reasoning, quickly see that before a company can constantly ask or expect the workers to heed safety suggestions, the company and its officials must "put their house in order" by laying down a concrete, definite safety program. For mines this includes primarily adoption of a to a logical mining method, the installation of safe miming equipment and practice the netting forth in definite form (preferably do a printed pamphlet) of the company's minimum safety requirements, and the organization of its operating officials into an accident-prevention body. After the company has its own affairs so arranged that it can go to its workers with "clear, hands" in promoting a safety program, the real work begins; and this is especially applicable in mining.

Jan 1, 1939

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels1. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m(26.5 ft) above the miner’s head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roofbeam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

Jan 1, 1999