Search Documents

By Wm. H. Woodhead

Improved methods of mining have accompanied the introduction of mechanical loading, of which there are a great many varieties, but this multiplicity of mining brings new problems and greatly increases the importance of managing over a few years ago. Few mines operating today have been opened with the intention of mechanizing throughout. The problem of mechanization is to change over a mine heretofore operated by hand methods and to select machinery that will fit the old system with the least number of changes, the aim being not to disrupt or to completely change the original plan. The organization of mechanical and electrical forces is a problem in mechanical loading, and each individual mine presents its own problems. Plans which may succeed in one mine may fail in another and upon the management rests the responsibility of deciding the best method in each case.

Jan 1, 1930

By Alla D. Mah

THERMODYNAMIC data for manganese and its inorganic compounds have not been critically surveyed since the work of Maier (31) 3 in 1934. At that time data were lacking or inadequate for many of the important metallurgical compounds. Experimental work, conducted during the intervening years, has supplied so many new thermodynamic values that it is again desirable to examine the available data and compile them into a single publication for handy reference. This paper consists of three main sections. The first summarizes the basic metallurgical thermodynamic data for manganese and its compounds, including heat capacities, entropies, heat contents, temperatures and heats of phase changes, vapor pressures, and heats and free energies of formation. All data available to May 1959 have been considered. The second section contains heats, free energies, equilibrium pressures, and equilibrium constants of reactions of manganese compounds, with special emphasis on metallurgical reactions. The third section supplies basic thermodynamic data for other elements and compounds encountered in metallurgical reactions of manganese, thus making it possible for the reader to conduct thermodynamic calculations without recourse to other literature.

Jan 1, 1960

By Aert Driessen

Australia has large resources of rare earths -- 4.35 Mt of contained rare-earth oxides (REO) in the demonstrated category and 1.69 Kt in the inferred category. Australia's demonstrated REO resources are contained in about equal proportions in placer deposits, which also host Australia's titanium and zircon resources, and in hard-rock deposits. The largest single deposit of rare earths, at Mount Weld in Western Australia, is contained in regolith overlying a carbonatite pipe. It has a demonstrated resource of 1.73 Mt of contained REO and yttrium oxide. The largest demonstrated resources of REOs in placer deposits are in the Murray Bash, southeastern Australia -- a total of 1.90 Mt of contained RE0 in six deposits. However, the REO-bearing minerals (monazite and xenotime) are of secondary importance and their recovery will be determined by the market for titanium dioxide and zircon. The Murray Basin and other pre-Pleistocene basins offer the greatest potential for discovering more REO resources. Australia produces about 7000 t/year of REO in monazite and xenotime nearly all from Western Australia, as by-product of mineral-sand mining; monazite production is about 12 000 t/year (6600 t REO) and intermittent xenotime production is about 50 t/year (25 t REO). About 8000 t/year of monazite containing about 4400 t REO is not recovered separately, or is lost in tailings, as is an unknown but smaller amount of xenotime.

Jan 1, 1992

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By Carlton D. Hulin

ARE we a "have" or a "have-not" nation in our domestic supply of metals and minerals? Impinging on the ears of a people weary of war and faced with the problems of reconversion to peace, the import of this question has built up with the momentum of an avalanche. Stemming from statistics cited by Pehrson and accelerated by the pessimistic and possibly biased statements of Ickes, hardly an issue of any technical periodical dealing with mining has appeared during the past year but within whose pages was to be found some comment, some discussion of the question: Are we a "have" or a "have-not" nation? We have proved commercial reserves of high-grade iron ore in the Lake Superior region sufficient for 22 years, based upon the prewar rate of consumption; commercial copper reserves to last only 34 years, one fourth being inferred ore; zinc sufficient for nineteen years, over half being inferred; lead for twelve years, two thirds of which is inferred; mercury for only three years. So read the figures. Although admitting that these figures may be extended by new discoveries, by the use of marginal and submarginal ore, and by further technological advances, are we nevertheless to assume complete pessimism in the acceptance of the meaning of these statistics; are we to expect a rapidly increasing dependence upon foreign sources of mineral supply; are we to believe that we are at or near the peak of the "metal age" as has been held by Theodore J. Hoover? Or is some more optimistic viewpoint possible?

Jan 1, 1947

By Steven A. Fechner

In 1991 and 1992, the Bureau of Mines completed chromium, platinum-group metals (PGM), and tin investigations, and started indium, manganese, titanium, and vanadium investigations in Alaska. These studies were done as part of the Site Specific Minerals Investigations project. As a result of this work, the Bureau found PGM-bearing composite plutons in the Yentna River area of the Alaska Range, which are chemically similar to composite plutons in other parts of the Alaska Range and to Ural-Alaskan type complexes. Previously unknown chromium and PGM occurrences were found in the western Brooks Range. A compilation report on the Bureau's chromium and PGM investigations in the western Brooks Range was also published. Indium was found in anomalous concentrations at the Lost River tin deposit. Small occurrences of manganese were located, mapped, and sampled in the Wiseman and Chandalar quadrangles, and in the Liberty Falls, Prince William Sound, and Homer areas. Tin occurrences in western Alaska were summarized in three Bureau open file reports. The beaches near Cape Yakataga and Yakutat were evaluated for their titanium potential and a sampling methodology was developed. Vanadium investigations included examining streams in the Wiseman and Eagle areas that contained anomalous vanadium values. In the Eagle area, high vanadium, uranium, and copper values were found in the basal layers of the Road River formation.

Jan 1, 1994

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By Luis Porras T.

La explotación de minas de cielo abierto requiere de la estabilidad de los taludes puesto que estos aseguran el eficiente minado de los bancos inferiores y garantizan las condiciones para los servicios auxiliares. Por ello, el presente trabajo señala el método de voladura controlada como el más adecuado para la estabilidad del talúd en explotaciones de límites finales. Dentro de este método, el criterio de velocidad pico de partícula refiere el grado de vibración producido en el terreno por los disparos, ajustándose en el cálculo de carga de los taladros. Sin embargo, en el caso de la mina Toquepala y por razones de índole estructural, el método de minado se aplica de forma moderada la zona Este. Asimismo las condiciones de este método quedan supeditadas a las condiciones geológicas, la infraestructura que se desea proteger y a los servicios auxiliares a complementarse.

Aug 26, 1988

By Michael J. Friedel

As part of an investigation aimed at mitigating the hazards caused by abandoned mine openings, the Bureau of Mines conducted a series of electromagnetic surveys in the Galena, KS, area of the Tri-State mining district. The application of monostatic ground-penetrating radar (OPR) and inductive electromagnetic methods for detecting and delineating hazardous mine openings and attendant features was demonstrated to be feasible for shallow mine workings (i.e., less than 35 ft) occurring below flat-lying areas. Accurate determinations of depth to a mine roof appeared to be limited to roughly 20 ft using the GPR method. Features such as mine voids, fractures, and zones of subsidence were located beneath the Mainstreet (State Highway 26) site using the GPR system. Both the GPR and inductive electromagnetic techniques satisfactorily located mine openings and pillars at the Hell's Half Acre site. Geophysical interpretations were supported by exploratory drilling and mine maps.

Jan 1, 1990

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

By R. W. Geehan

The Yellow Pine zinc-lead mine, situated about 3-1/2 miles northwest of Goodsprings, Clark County, Nev., was explored by core drilling during the fall of 1942 and the summer and fall of 1944 by the Bureau of Mines in cooperation with the Federal Geological Survey. The Yellow Pine district was located in 1855. The original claims covering the Yellow Pine mine were located in the following years: Rover, 1892; Hilo, 1897; Bybee, 1900; Radio and Como, 1906. The mine was operated by the Yellow Pine Mining Co. from 1906 to 1929. This company was dissolved in 1935. At a later date, S. E. Yount and the Security First National Bank of Los Angeles, Calif., acquired ownership of the mine. Since 1939, the mine has been operated in a small way by leasers. Production has been at least 175,000 tons averaging about 10 percent lead and 25 percent zinc, with a gross yield of $5,785,174. Virtually all ore produced by this mine consisted chiefly of oxidized zinc and lead minerals and came from long, pipelike shoots in the 100-foot thick Yellow Pine limestone. Ore shoots are sharply defined; elsewhere, the limestone is nearly barren. Numerous faults cut the mine into blocks. Ore is now mined in an open stope, but in the past, large tonnages wore mined in stopes by square-set methods. Ore produced recently was shipped direct to smelters unprocessed; in the past, it was milled by gravity and produced separate lead and zinc concentrates.

Jan 1, 1949

By R. M. Brick

EDUCATIONAL benefits for veterans of World War II have largely removed one of the two former barriers to a college education for everyone, namely financial means and intellectual capacity. This latter limita¬tion has not kept privately endowed institutions from increasing 50 to 100 percent in size of student body, even after applying moderately rigid entrance standards. Growth of some land-grant universities, which cannot well exercise such restrictive judgements, has been even greater. After a weary board of admissions, subject to student, alumni, faculty, and even political pressures, has admitted double the former number of freshmen, the university's worries really begin: to find laboratory, classroom, and instructional facilities. If this were a one- or two-year problem, the answer would be simple: double up, hold night classes, particularly of laboratories, rent space, and have instructors work 24 class or contact hours a week instead of twelve (it takes usually two to three hours of outside work by the instructor for one hour in class). However, most engineering school faculty men are worn out now from four to five years of "accelerated" (frequently downward!) programs and they couldn't continue teaching in a way satisfactory to their own consciences on

Jan 1, 1947

By N. H. Coates

The Bureau of Mines determined average film coefficients of heat transfer for helium flowing through smooth, water-cooled tubes at Reynolds numbers of 5,000 to 25,000, helium inlet temperatures of 1,600° to 2,600° F, average temperature difference across the helium film of 800° to 1,300° F, and heat flux to 215,000 Btu/(hr)(sq ft). Since helium was the only gas used, the ranges of values for physical properties of the fluid are limited--thermal conductivity from 0.15 to 0.20 Btu/(hr)(sq ft)(O F/ft), viscosity from 0.082 to 0.104 lb/(ft)(hr), and Prandtl number from 0.63 to 0.68. Four equations, three of them dimensionless, correlate these coefficients with other properties of the helium--bulk temperature, film temperature, dimensionless parameters based on temperature, and the ratio of wall temperature to bulk temperature.

Jan 1, 1966

[A Aalseth, Earl P. (M 51) Geol, Amerada Petr. Corp., Box 1498, Billings, Mont. Abadie, Henry G. (M 43) Asst to Supvr of Oper, Long Beach Oil Dev. Co., 255 S. Santa Clara, Long Beach 7, Calif. Abbe, T. Waldo (A 56) Ass't Dist Oper Supt, Sun Oil Co., Beaumont, Tex. Abbott, J. L. (M 56) Partner, Pritchard & Abbott, 501, Century Bldg, Fort Worth, Tex. Abbott, Richard H. (J 51) Owner, Abbott & Howard, 422 W. Hermosa, San Antonio, Tex. Abbott, Seth J., Jr. (M 51) Tekoil Corp., .2;A6 Mercantile Nat'l. Bank. Dallas, Tex. Abbott,. William G. (M 50) Div Mgr, Rice Eng. & Op. Inc., Box 1142, Hobbs, N. M. Abderhalden, R. R. (J,59) Box 100, Carmi, Ill. Abel, Malcolm D., Gen Mgr, Bakke Oil Co., Midland, Tex. Abel, Raymond L. (M 28) Prof of Chem Engr, Univ. of Pittsburgh, Pittsburgh 13, Pa. Abel, Wayne K. (M 57) 1513 Patton Drive, Odessa, Tex.]

Jan 1, 1961

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By Leo J. Neill, O&apos

Abrasives are essential to the manufacture of munitions - airplanes, gas, shells, tanks, and in fact every product that involves metal forming or finishing. An indication of the importance of abrasives in the national defense and aid-to-Britain programs is the close peace-time correlation between demand for abrasives and automobile production, which in recent years has consumed more than 35 percent of the total output of abrasives. Unprecedented demands on the abrasives industry are forecast by the rapid expansion in airplane output, tie increased mechanization of all armed forces, and the consequent speeding up not only of the factories where finished munitions are made but also of the steel mills and other factories were additional large quantities of abrasives are needed for snagging or rough-grinding semifinished products before they can be used by the fabricators. A recent survey by the artificial abrasives manufacturers indicates that they can readily increase their output 75 percent compared with the previous peak of 1937 without building new plants. By overhauling production schedules, their maximum production possible could be increased to 182 percent of the 1937 output, and the nature of the industry is such that plant capacity could be increased rapidly if need therefor should arise. No figures on the estimated requirements for abrasives in 1941 or 1942 have as yet been compiled, but the industry feels that it can meet demands as they develop.

Jan 1, 1941

By Robert J. Evans

Reclamation costs were estimated for 20 coal surface mining operations in the Appalachian and Midwestern Coal Supply Districts (these two districts were divided into three multi-State regions). The cost data were obtained through onsite observations, interviews with mining company personnel, and the authors' cost estimating procedures. The cost data are presented in terms of dollars per acre, dollars per ton of coal produced, and dollars per cubic yard of overburden moved during backfilling. The reclamation process is divided-into three cost categories: Premining planning, backfilling, and revegetation. The average total reclamation costs for the three regions are $2.77 per ton of coal produced and $8,168 per acre. As the result of comparisons of reclamation costs by region, by mining method, by slope, and by size of operation, the most important reclamation cost difference is between area mining methods ($1.73 per ton) and contour mining methods ($3.81 per ton). The Federal Bureau of Mines conducted this study to determine as accurately as possible the actual costs involved with the reclamation of coal surface mined land done in conjunction with active mining operations.

Jan 1, 1975

GARY STUBBLEFIELD RMCMI PRESIDENT 1993-1994 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 90th Regular Meeting and Convention June 26 thru 28, 1994 Snowmass Resort, Colorado

Jan 1, 1993