Search Documents

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer's analysis were employed. MEYER'S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer's analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By Ivan V. Klumpar

If components of a gas-liquid stream react with each other and with stationary solids, involving parallel and sequential, reversible and irreversible, and slow and instantaneous reactions, the process can be defined by a set of simultaneous differential rate equations and simulated as multistage semibatch re¬actors. Each stage is divided into finite time increments. Within each increment, even the simultaneous reactions are treated as sequential. The proposed method follows process evolution from non-steady state startup to normal operating conditions. It allows computing byproduct buildup in recycles, tracer response curves and, in case of underground processes, expansion to adjacent parts of the deposit.

Jan 1, 1979

By L. Adler

A relatively simple and effective technique is proposed to deal with the failure of geologic masses containing weakness planes. This technique, termed irextended" rupture envelope, provides a means to clearly distinguish rock and soil from fractured rock and, on a theoretical level, considers a matrix-inclusion system. It may also constitute the link between Mohr's and Griffith's failure theories. Included in the article are five sample problems concerning site location, structural design, strengthening the plane of weakness, changing the magnitudes of major and minor principal stresses and changing the orientations of major and minor principal stresses. Engineers trying to solve design problems in rock and soil mechanics have often assumed an iso-tropic and homogeneous medium. For naturally occurring geologic masses this assumption has always been viewed with regret. The following analysis which deals with the effects of plane anisotropy on failure presents a solution to this. The planes of weakness are joints, faults, bedding planes, fracture and cleavage (natural and induced), foliation and schistosity. The physical properties of these weakness planes include an undulating surface, frictional resistance, discontinuous extent, filling material, tightness and presence of water to cause a hydrostatic pore pressure. All of these properties relating to failure can be summarized in Mohr's rupture envelope for the plane of weakness. This, along with the geometrical orientation, strike and dip, of the plane of weakness produces what is termed an irextended" rupture envelope. MOHR'S STRESS CIRCLE AND RUPTURE ENVELOPE The significant features of these concepts are listed below.' 1) A point on the u - r coordinate plane represents the normal and tangential stress components on a reference area in the material. This area can have any orientation. (Fig. la)

Jan 1, 1963

By M. M. Rao, P. G. Winchell, R. J. Russell

A detailed analysis has been used to correlate the avalable thermodynami c da In on iron-ric11 Fe-Ni (41loys in the body-centered a, and the face-centered y phases. The inp ut injovrt~ation required by the a am lysis consists of tile heat of the a, to y transformation at 1123°K, the heat of mixing of y at 1123°K, tile specific heats of both a, and y (decomposed into Debye, electronic, and magnelic contributions), and the positional and magnetic entropies of both a, and y. PYLrrzary oirt.bul of the analysis is the free energy of each phase as a Junction of temperature and composition. FOr Fe-Ni alloys the adjustment of twenty-one parunletevs allows the accurate reproduction of enthalpy data for both phases, the heat of mixing- for y, the a/y equilibrinm compositions in the Fe-Ni phase diagram, and the usually accepted enthalpy and entropy of a and y iron. Also obtaitzed are fuirly accurate reproductions of electronic specific heat coefficients predicted from electron- to-atom ratio interpolations and To temperatuves eslimanted from transformation studies. Also considered in the calculation are the elastic constants, Curie temperatures, saturation magnlelizalion values, and indications of short- range order. The measnred activity coefficient of iron in anstetnite could not be accurately matched. The major source of uncertainty in the model is thought to be the magnetic contribution to the entropy of austenite. Calcrclations were extended to Fe-ni-C alloys using available carbon-acliuity data. The free energy of transformation from martensile to r at fixed composition was obtained as a function of nickel and carbon contetzt, and binary thetal-carbon phase diagrams Were estimaled as a function of nickel contenl. We needed thermodynamic information for Fe-Ni and Fe-Ni-C alloys at temperatures between 400" and 800°K in order to interpret the results of several phase-transformation studies. The most recent theoretical analysis of the thermodynamics of Fe-Nialloysl was based on a lumped-parameter, regular-solution model and used the Fe-Ni phase diagram available at that time.' Because significant difficulties were encountered in attempting to extend this analysis to Fe-Ni-C alloys, and because more experimental data has become available recently, we decided to attempt a new correlation. The analysis used here allows the extrapolation of measured and calculated thermodynamic values to lower temperatures and the extension of the thermodynamic analysis to Fe-Ni-C alloys. The structure of this correlation consists of expressions containing a total of twenty-one adjustable parameters. The forms of these expressions are discussed in the next section; however, a less formal summary is presented now to provide a physical overview of the model and to indicate its connections to prior work. Primary input information for this correlation is described below. The measured values of the specific heat of iron3 and its analysis475 and theoretical estimates of the specific heat of y* iron at low tempera- loys at 1123°K has been measured by solution calori-metry.7 The enthalpies of both a, and y have been measured most recently by Scheil and Saftig,B who used a dry-ice calorimeter. These data are used to formulate expressions for the heat of mixing of y and the heat of transformation of a, to y both at 1123°K. The a and y solubility limits in the Fe-Ni phase diagram have been redetermined recently9 by methods which assure a close approach to equilibrium. The a to y transformation can occur without change in nickel content or free energy at a temperature called TO; TO temperatures for various nickel contents have been estimated from transformation studies. The computed free-energy functions are adjusted by means of the parameters to fit both the phase diagram and the TO temperatures. Primary emphasis is placed on the phase diagram fit. Iron activities have been measured in Fe-Ni austenite10 between 973" and 1173°K. These activity data, which cannot be fitted accurately with our model, indicate that iron is substantially ideal in iron-rich austenite. Secondary, but helpful, information for the present correlation is provided by neutron diffraction and saturation magnetization measurements on both body-centered and face-centered Fe-Ni alloys."-'3 These results were interpreted11 in terms of composition-insensitive, localized magnetic moments on both iron

Jan 1, 1968

By Peter Duniam, Vivian Patz

History of the ExEx 1000 CAB system. l What we’ve learned using electronic timing. l Requirements for a second generation. EDD system. l The ExEx 2000 system - simple, versatile and cost effective

Jan 1, 1997

By Joseph Singewald

AMONG the genetically interesting iron ores of the United States are those of the St. Francis Mountains near Ironton and Iron Mountain, Missouri. They are specular hematite in porphyry. The Iron Mountain and Shepherd Mountain deposits are generally spoken of as veins and those of Pilot Knob, Cedar Hill, and Russell Mountain as bedded deposits. Iron Mountain has produced nearly 4,000,000 tons of ore and Pilot Knob about 1,500,000 tons. The output of the other three localities has been insignificant. Pilot Knob is no longer worked as an iron mine, but the rock is now being crushed for use as road metal. Iron Mountain has continued as an active producer. In 1927, the property was acquired by the M. A. Hanna Co. and an extensive prospecting and exploration campaign was undertaken, so that the ultimate production of Iron Mountain will doubtless greatly exceed the figures mentioned.

Jan 1, 1929

By A. Nhasengo

Paper written on project work carried out in partial fulfilment of B. sc. Eng (Mining Engineering) The purpose of this investigation was to assess the mining strategy for steep reefs at Mine A mine in 2005 and 2006. Reefs steeper than 35° were discovered when production commenced at the mine. At that time reefs steeper than 35° were not popular in South African tabular gold mines, therefore new techniques of mining them had to be developed. The underhand mining method was chosen for this purpose. The project was about assessing ventilation, support costs, local support cycles, adherence to the mine?s support standards, mine planning and efficiencies of the underhand mining method. The project work was covered by doing a literature research for underhand mining methods and performing a literature review of the mining methods, support methods, ventilation standards at Mine A. Underground visits were conducted at Mine A mine for data collection, and Mine B was visited to obtain information on support costs and efficiencies. During the investigation it was realized that the underhand mining method was an appropriate method for mining steep reefs; however, there were some challenges related to ventilation and support installation. Efficiencies could be realized with the underhand mining method and planning and scheduling were not different from breast mining.

Jan 1, 2007

By Zach G. Agioutantis

The prediction of ground movements due to underground mining using the influence function method is a mature technology, widely used by researchers and planning engineers around the world. Surface strain, either tensile or compressive, is an important indicator of potential impacts on structures such as buildings, bodies of water, pipelines, railway and power lines, and tailings dams. Calculation of static or dynamic surface strains, for varying surface terrains and slopes, should be accurately predicted and be independent of the methodology applied for the calculation. This paper discusses and compares the development of horizontal and ground strains on the surface due to underground mining for different surface topologies (sloping terrain, monitoring lines, etc.) and presents the steps needed to ensure accurate calculations. Examples are given to demonstrate how ground strains can be calculated for one- and two-dimensional gridded surfaces.

Jan 1, 2013

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By T. A. Rickard

The lode-formation of the Bendigo gold-field was described in a former paper.* It presents a striking identity of arrangement with the general geological structure of the region, which is one of comparative simplicity. The alternating beds of slate and sandstone which constitute the prevailing country-rock have been extremely contorted ; yet notwithstanding their highly developed cleavage it is possible to discern in their structure the evidences of original sedimentation. Along the crests of the waves which are the axes of anticlinal folds occur bodies of gold-bearing quartz, of great economical importance, which the miners have appropriately termed " sad-

Jan 1, 1894

By Gilbert E. Doan, William C. Schulte

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By William C. Schulte, Gilbert E. Doan

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By G. Drennan, A. Cameron

"South African mining operations depend on the skilled professionals produced through the tertiary education sector. In geoscience courses at the University of the Witwatersrand, which lead into the mining sector, there has been a significant increase in student intake over the past 15 years. This increase has been characterized by a radical shift in demography: in classes where white male students once formed the majority, black female students are now in the majority. This demographic shift appears closely linked to policies addressing issues of social justice and transformation in post-apartheid South Africa. We document this change and consider the role played by employment equity legislation (as in the Mining Charter) and corporate social investment strategies in the mining industry, notably through bursaries offered to black female students. We also look at the changing needs of the industry, where the critical need for managerial skills, not just technical knowledge, is highlighted through data from surveys of past students and industry managers. Our findings indicate the need for a curriculum adjustment to meet these changing requirements, as well as more rigorous selection criteria for bursars than simply gender, race, and appropriate matric results. IntroductionThe South African economy has historically been linked to mining and the exploitation of mineral resources. South African mining operations are dependent on the professional labour that is produced through the tertiary education sector, with critical thinking, teamwork, and the art of negotiation having been identified as the crucial skills required for this industry (Sideropoulos, 2014). Over the past three decades the South African system of education has gone through a period of dysfunction that it is struggling to rectify (Maphai, 2014). This has impacted on the levels of academic preparedness of students applying for places in higher education. Concurrently, government and university policies have widened access to higher education in response to the need to address issues of social injustice and transformation related to South Africa’s history of apartheid. As a result, the number of students admitted to universities has increased dramatically. In the School of Geosciences at the University of the Witwatersrand (Wits), the increase in student numbers has been accompanied by a significant change in demographics: classrooms which in the past were dominated by white males have given way to classrooms in which black females are often in the majority. This demographic shift is related to legislation such as the Mineral and Petroleum Resources Development Act and the Broadbased Socio-Economic Empowerment Charter, developed to reshape the socio-economic and equity frameworks of the country (Botha and Cronje, 2015). Requirements aimed at transformation in terms of management, skills development, and employment equity, together with corporate social investment (CSI) requirements, have resulted in bursaries being made available to attract students from designated groups, which in turn has increased the number of black students, and notably black female students, taking courses in geosciences. However, due to the economic downturn, instability in the mining industry has recently resulted in the downsizing of some mines, with international investors pulling out of South Africa. This instability resulted in devastating strikes across all sectors of the mining industry (Stewart, 2013) and in Marikana, an important platinum mining area, the strike culminated in a deadly shoot-out between miners and police. The resulting tensions spilled over into the gold mining sector, resulting in further strike action, shaft closures, and retrenchments. These challenges have implications not only for the mining industry in South Africa, but for the tertiary education providers whose graduates would have been absorbed into the mine-related workforce."

Jan 1, 2017

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.' Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965