Search Documents

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

THE Company's smelting equipment consists of three blast furnaces, supplied with blast from two sets of vertical piston blowers, each capable of delivering 8000 cub. ft. of air per minute at a pressure of 60 oz. per sq. in. Each blower is belt-driven by a 1:30 h.p. motor. The maximum speed of the blowing engine is 35 r.p.m.No. 1, the largest of the three blast furnaces, has a crucible area of 49.5 sq. ft., and measures 11 ft. 6 in. x 5 ft. at the tuyeres.From tapping floor to feed floor measures 35 ft. 9 in., and holds, when full, 100 tons of charge. Blast enters through thirteen 3-m. tuyeres at 60-oz. pressure. Working normally, this furnace is capable of treating :300 tons of charge, exclusive of returned slag and coke, per 24: hours, with an output of 100 tons of lead. Tapped slag flows into a C.l. forehearth mounted on wheels, where any lead and matte is caught, and the slag overflows into a 3-ton cast-iron pot, in which it is drawn away by an electric locomotive and poured over the dump.

Jan 1, 1918

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

By P A Ferenczi

The Proterozoic iron oxide related Au-Cu-Bi (Tenant Creek style') deposits at Tennant Creek can be classified as syntectonic polymetallic hydrothermal replacement type mineralisation. These deposits have characteristics in common with a number of other Proterozoic iron oxide (Cu-U-Au-REE) hosted deposits in regions which include Southeast Missouri, USA; the Kiruna district, Sweden; the Great Bear Magmatic Zone, Canada; the Stuart Shelf, South Australia; and the Wemecke Mountains, Canada. Similarities between these and Tennant Creek style deposits include: 1. Tectonic Setting: Formed at shallow crustal levels (

Jan 1, 1994

By Warner R. E

Present capacity for molten iron production at Port Kembla is an average of 13 000 t/day from five blast furnaces. The most recently installed blast furnace, No.5, was commissioned in March 1972 with a design capacity of 4 500 t/day. For the first reline currently scheduled for 1977, plans are being finalized.for significant modifications and uprating of capacity. Achievement of the initial design capacity from No.5 blast furnace on a sustained basis was not realised until the third year of operation. Although the furnace is only 42% larger than No.4 blast furnace on an inner volume basis, the more stringent raw materials, operation and maintenance requirements of the larger furnace and more complex equipment have been found to be much more critical than anticipated in the planning stages. These problems have also been experienced by many other companies who have recently installed large new blast furnaces. Some of the principal problem areas are described together with measures taken to over- come the difficulties. The problem areas include the failure of'the shower cooled bosh, failure of the upper shaft brickwork, sludge

Jan 1, 1976

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

By Mandzic E. H

The Dome Mine of Timmins Mining company is located in South Porcupine, N.W. Ontario. The orebody being mined partially lies in the No. 3 shaft pillar. Stability analysis has been carried out to establish the influence of nearby mining on ground movement in the shaft vicinity. Mathematical modelling of shaft displacement has been done for stope layout at depths from 180-210 m and distances of 10-50 m from the shaft. Analysis indicated that ground displacement around the shaft is below 1 mm/m and one third less for cut and fill than in the case of open stope mining. The result of the investigation was later confirmed by cut and fill mining of this orebody.

Jan 1, 1986

By Zenari L, Kent D

As our mines introduce more sophisticated production technology into their operations, the dependence on communication systems is markedly increased to allow the management of the technology. However the attention given to the communication systems has lagged that given the production equipment - namely LHDs, trucks and jumbos. At times it was treated as after thought. However, this is changing as the degree of automation increases in our mines. The communication system is now being given much more priority and is genuinely becoming a part of the mine design. The transfer of information around underground, as well as between the surface and underground, is an essential day-to-day activity, with the aim being a smoothly run operation. However the mine environment is far from static, and situations arise - such as breakdowns or other incidents - that require swift analysis of the issue, its cause and its remedy. Also, as communication systems become more sophisticated their use in areas, other than direct data flow, become available. The importance of communication, its development, and new areas being impacted by communication is the subject of this Paper.

Jan 1, 1997

By Dagbert M, Belisle J. M

Several packages for the estimation of porphyry type deposits exist and produce acceptable results. Recently, however, the need for really trying to obtain maximum information from drill holes has prompted the generation of geostatistical solutions to the problem of reserve calculation. It will be shown that an understanding of a few key points is necessary in order for these solutions (variogram analysis and kriging) to he really ptimal. The most important new fact to be ecognized in open pit ore reserve estimation is that block models do not give an accurate rediction of ore tonnage when a cut-off is pplied but often yield an overestimation of p to 25%. When checked against extensive roduction records, geostatistical methods provide a practical solution to this problem. t now seems that the model used here gives he best possible results. Inasmuch as all arge deposits present very similar geostatis- ical characteristics only a few days of work re necessary to produce a complete inventory f these. The techniques used will be demon- trated using examples from five deposits and pecial emphasis will be given to the accurate rediction of tonnages of ore and waste using he new "transfer function" technique of G.

Jan 1, 1977

By M, C Silveira, C Ellice, D Christensen

Peak Gold Mines (PGM), a member of the Rio Tinto Group, is an underground and open cut gold mining operation located near Cobar, NSW. A multi-phase study was initiated in 2001 in support of developing a dry æmoisture store and releaseÆ cover system design for the PGM tailings dam, which contains potentially acid-forming tailings material. The first phase consisted of characterising the tailings and potential cover material (waste rock from an open cut operation) as well as soil-atmosphere cover design modelling. The second phase involved construction of two cover system field trials on the tailings dam and installation of a variety of field instruments to monitor the hydraulic performance of the test covers during all seasons of the year. Field performance monitoring commenced in April 2002 and will continue for a minimum of two wet-dry climate cycles (third phase), prior to using the field data for calibration and subsequent validation of numerical models developed for the cover system trials (fourth phase). This paper describes the work completed for the first two project phases and also discusses the initial performance of the cover system trials.

Jan 1, 2003

By McManus D

Situations where in-pit bench stripping methods are favourable are introduced. Examples from Peak Downs Mine are used as a guide to the range of methods available.A number of geological and geotechnical conditions adverse to successful in-pit bench stripping are described. In all cases bench, floor, and/or final lowwall instability can develop and compromise the economics of extraction.

Jan 1, 1992

Conventionally, a combined system consist- ing of a dry or wet pulverizer and kneading mac- hine is applied to the pretreatment of fine mat- erials for agglomeration, especially for pellet- izing. However, treatment cannot be expected to be satisfactory owing to the complexities of the process. A new process was developed to over- come the defects inherent in the conventional process. This new process treats certain fine materials having a moisture content somewhat lower than that suitable for pelletizing in a ball or rod mill. The mill is of special de- sign in which grinding and strong kneading are performed to give an extremely homogeneous ball- ing material with appropriate size distribution and pelletizing characteristics. The most serious problem in this process is the choking of sticky materials in the mill. A specially designed rubber lining was installed in the mill to overcome this trouble. This paper presents actual results from our iron ore pelletizing plant relating to the pelletization of other fine materials.

Jan 1, 1974

By Fairhurst RM

High pressure abrasive water jets have been shown capable of cutting a wide range of materials including steel, stone, rock and concrete. Acceptable performance can be achieved using relatively low pressures and expendable abrasives. The cutting head can be made small and abrasive feed systems have been developed that allow reliable pumping of slurries over long distances to supply such cutting heads. These features make abrasive water jets ideally suited to automated control in remote areas.Another major advantage of abrasive entraining water jet cutting heads is that they may be operated safely in potentially explosive environments due to their cold cutting ability. Therefore there are many possible applications for such equipment in mining.This paper gives an introduction to the abrasive water jet process and includes results of trials carried out at BHRA on a range of hard materials. Work is also described which investigated the operational safety of abrasive water jets in explosive environ-ments. In a special environmental chamber, cuts were made on steel and sandstone with atmospheres of methane/air and hydrogen/air, without caypsing ignition.

Jan 1, 1985

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

By J Rayo

Andean countries (Chile, Peru, Bolivia and Argentina) have 42 semi-autogenous mills (SAG) in operation and there are more than 30 projects in the pipeline that consider SAG mills. At the end of the next decade, the total amount of SAG mills in this area will likely be close to 100.There is a lot of reliable operational information collected by JRI Ingenieria Sociedad Anonima, the author’s engineering company, for more than 20 years and processed by statistical software, to be used as a reference for design basis of future projects or to improve operations by comparison. JRI Ingenieria Sociedad Anonima has reliable information related to the performance of more than 50 per cent of the Andean SAG plants.The paper presented considers a set of graphs that summarise the collected and verified SAG plants technical data. The figures will show key parameters as circuits and equipment data, energy consumption, technical availability, utilisation rates, throughput variability, pebble productions, steel consumption and others.The data is compared with typical design basis of several engineering companies and the main differences are analysed and/or commented on.CITATION:Rayo, J, 2014. Comparison of semi-autogenous mills operations in Andean countries, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 283–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

By T Mizuta, D Ishiyama

The Vienna Wood hydrothermal is hosted by mid-oceanic ridge type basalt in graben morphology and is located in the Central Manus Basin. The hydrothermal field is about 300 metres in diameter and consist of a sulphide mounds and tall huge death and active chimneys. From the three distinct ore types collected from the Vienna Wood site, the dominant ore minerals recognised are pyrite, wurtzite, sphalerite, chalcopyrite, Fe-oxide and gangue minerals of anhydrite, gypsum, barite and silica. The consistencies in the paragenetic sequence and in the spatial distribution of the sulfides across the three ore types suggest that similar hydrothermal process exist across active and death chimneys. Fluid inclusion studies reveal a homogenisation temperature of 190-260¦C and an average salinity of 5.1-5.4 wt per cent NaCl equiv. The pH of the hydrothermal fluid ranges from 4.2 to 6.1. Bulk chemical analyses indicate that the mineralisation in the Vienna Wood can be classified into the Zn-(Cu-Pb) type of mineralisation. The tenors of the ore and mineral assemblage resemble those of the Mid-oceanic ridge system and ancient ophiolite hosted massive sulphide deposits of Cyprus and Oman.

Jan 1, 2002

Average annual growth in consumption of primary energy in Australia over the past 10 years has been 5·5 per cent compared to a world average of 4·1 per cent.Over the next 10 years growth rate is expected to increase to 6 per cent per annum due largely to the rapid development in the mineral processing industry.By the end of the 19705 natural gas is expected to supply more than 9 per cent of Australia's primary energy market. Coal will supply 40 per cent and petroleum products 47 per cent. Nuclear energy will make its appearance but will make only a small contribution in the period.Australia has adequate reserves of natural gas and coal to supply its needs in the 1970s and beyond. However the newly developed reserves of crude oil, while supplying 60-70 per cent of requirements in the initialyears, will need regular and sizable additions if they are to keep pace with the expanding consumption. For Australia to become self sufficient in the period 1970-1990 it is estimated that new discoveries will need to approximate ten times the volume of recoverable reserves found in Australia to date.

Jan 1, 1971