Search Documents

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By Norman O. Lotter

The problem of quantifying the full performance potential of an ore body in a concentrator, and how to configure a flowsheet to achieve that potential, either for a new operation or an existing one, is a strategic challenge. Modern flowsheeting technology that has been developed over the last twenty years has provided a suitable platform to achieve this. The integrated use of geology, compositional and quantitative mineralogy, sampling models, quality controls, and mineral processing, including flotation testing, has evolved into what is now called process mineralogy. Two specific tools have been developed and validated as standard methods in this toollbox. These are statistical benchmark surveying and high-confidence flotation testing. Both of these have borrowed from the sampling theories of Pierre Gy and from geostatistics. Additionally, they work on a replicate measurement and averaging basis, thus reducing the overall random error level. With this arrangement, one is in a position to characterize the ore from true samples and identify and quantify the economic minerals present in a manner that easily brings out the processing implications and likely grades and recoveries. In particular, the approach captures the variation in the ore body, which, if properly translated into the flowsheet design, minimizes the risk that unexpected responses will develop in the concentrator operations. A further advantage is that successful plant trials are now possible and practical. An overview of this approach is presented with two case studies.

Jan 1, 2011

By Gordon Revey

Over ten million pounds of explosives are used daily to blast rock in mines, quarries and construction projects throughout the United States. Despite the immense volume of explosives used, serious incidents involving the legal use of explosive materials are rare. Unfortunately, when incidents arise they are well publicized, whereas the great majority of blasting projects-even the most challenging ones—quietly occur without incident or public recognition. Although unfair, media coverage focuses on incidents and/or accidents, and as a result skews the public’s perceptions of our industry. These negative perceptions about blasting profoundly effect our work. Most apparent are the community groups who organize to fight blasting work. However, other impacts are more insidious and have long-term effects on our industry. For instance, planning engineers or government agencies often prohibit blasting to avoid the public’s adverse reaction or because of general fear of blasting impacts. Ironically, as regulations and specifications continue to curtail our industry, the net effect is an increase in the cost of rock excavation. As taxpayers, we suffer needlessly by paying more for government funded construction projects. As blasting professionals we are additionally penalized through loss of work.

Jan 1, 2001

By M. Beus, S. Inverson, B. Stewart

Abstract Recent ore pass failures have underlined the need for improved designs, standards, structural mon¬itoring methods and better hang-up prevention and removal tech¬niques. Researchers at the Spokane Research Laboratory of the Na¬tional Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remedia¬tion strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading condi¬tions. A full-scale mockup of ac¬tual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com¬pared Loads on an active ore pass chute were measured.

By Manuel Gomez

Bituminous coals having maximum fluidity values in the 40- to 25,400-dial-divisions-per-minute (ddpm) range were carbonized in a continuous, entrained-bed reactor. Carbonization was conducted in an 8-inch diameter, vertical reactor at temperatures from 955° to 1,345° F and at air-to-coal ratios ranging from 4.63 to 16.12 scf/lb of moisture-and ash-free coal charged. Carbonization rates from about 118 to 360 lb/hr, as-carbonized basis, were examined. It was demonstrated that carbonization temperature and air-to-coal ratio must exceed minimum values for continuous operation. Within the operating conditions discussed, highly fluid bituminous coal was carbonized to produce tar and nonagglomerated char. The yield of tar ranged from 21.3 to 38.9 gallons per ton and the char yield ranged from 1,109 to 1,563 pounds per ton, all units expressed on a moisture-and ash-free basis. It was demonstrated that the maximum fluidity and the average size of the coal along with the air-to-coal ratio and the carbonization temperature act together to influence the carbonization product yields and certain properties of the products. Prediction equations were developed from the data for product yields and selected properties of the char, tar, and gas.

Jan 1, 1968

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By E. Contestabile, R. von Rosen, R. Guilbeault, R. Fouchard, P. Lightfoot

In August 1998, a truck loaded with 18 tons of blasting explosives, including over 13 tons of ANFO, left the road near Walden, Ontario. The crash caused a fire; approximately 30 minutes later a large detonation occurred, causing substantial damage to the roadway and local property. Although nobody was injured in the explosion, the consequences of a similar incident in a heavily populated area could have been catastrophic. Following the Walden incident, Transport Canada and Natural Resources Canada embarked on an extensive experimental program to determine the cause of the detonation. This paper describes part of that experimental program, designed to understand better the thermal decomposition of ANFO.

Jan 1, 2003

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By Hibbert W. D, Lottrey A

The behaviour of coal in a process is a function of both the coal properties and the processing conditions. In the case of the Loy Yang coal deposit, extensive testing has been undertaken to determine: ò the extent, distribution and structure of the coal resource; ò the variations in properties throughout the resource; and ò evaluation of the behaviour of the coal during processing. This has involved the conduct of an extensive borehole drilling program, backed by geological modelling and material characterisation (chemical, physico-chemical and petrological). Evaluation of the behaviour of the coal during processing has ranged from theoretical modelling, laboratory-scale investigations through to pilot scale and full-scale tests. Until recently, the bulk of the work was directed at evaluating the behaviour of the coal for existing pulverised fuel (pf) firing/steam boiler technology and a high level of understanding has been developed of both the coal resource and its behaviour within these systems. More recent efforts have been directed towards the evaluation of new technologies directed towards cheaper and more efficient power generation using this coal. Loy Yang coal has been evaluated in the following technologies: ò Hydrothermal dewatering/direct coal-fired gas turbine; ò Steam fluidised bed drying; ò Solar drying/densification; ò Briquetting; and ò Gasification.

Jan 1, 1992

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008