Search Documents

By H. M. Friede, R. H. Steel

Notes on Iron Age copper-smelting technology in the Transvaal by H. M. FRIEDE, Ph.D. and R. H. STEEL (Visitors) Earlier reports on Iron Age copper metallurgy and copper-smelting techniques in the Transvaal are surveyed, and a description and tentative classification of the copper furnaces are given. The analyses of furnace slags and sherds of glazed crucibles from archaeological sites of the Transvaal and the neighbouring Orange Free State pro. vide evidence of copper smelting there in Iron Age times. . An investigation conducted by the Department of Archaeology of the University ofthe Witwatersrand provided information on the details of furnace construction and smelting processes, on the composition of the materials used and produced, and on the making and handling of tools and accessories, such as bellows and tongs, needed by Iron Age smelters. Three models (the KaondejVenda furnace, the Rooiberg crucible furnace, and the Uitkomst furnace) were constructed and operated as a demonstration of Iron Age copper smelting as it was practised in the Transvaal.

Jan 11, 1975

By G. Rebel

Owing to the helical construction of the wires and strands in a triangular-strand rope, a torque is generated when the rope is restrained and tensioned. When a rope is suspended vertically, there is a load differential along its length due to the self weight of the rope. This load differential gives rise to an initial torque differential m the rope. Since the rope is constrained only at the conveyance and sheave wheel, the torque along its length must be constant ID order to maintain equilibrium, a variation in lay length occurs so that the lay length at the conveyance end decreases, and the lay length at the sheave end increases, from the manufactured state. The tension-torsion testing of steel-wire ropes is discussed, and it is shown how the results of the tests can be used to predict static in-shaft torsional behaviour. The expected changes in strand lay length in very deep shafts (deeper than 2500 m) are calculated, and the associated problems and of severe changes m lay length on rope endurance and safety are discussed. Examples of current in-service rope distortions such as kinks and corkscrews are shown.

Jan 1, 1996

By C. L. E. Swartz, I. J. Barker, J. H. Schubert

A dynamic simulator of the leaching and adsorption cascades of a gold plant was developed and used to compare the effect of various disturbances on the overall efficiency of the plant. These comparisons show which disturbances most critically need to be controlled to optimize plant performance. The simulator was based on an existing gold plant. Dynamic and steady-state data were collected on the plant and were used in the modeling of the process. Simple dual-rate models are used to describe the leaching and adsorption processes. Mole-balances of various species take into account the changes of concentrations in the leach, and also the movement of pulp and carbon up and down the adsorption cascade. Fluctuations in the flow rate, density, and cyanide concentration of the feed to the leach have a negative effect on the efficiency of the leach, while carbon attrition was found to be an important factor in decreasing the efficiency of the carbon-in-pulp (GIP) section. Badly regulated transfers contribute towards the decreased efficiency of the GIP section, but overflows and carbon leakage have only a limited long-term effect. Various carbon profiles and transfer schemes were studied, and the results indicated that a slightly heavier loading at the bottom of the cascade is beneficial, while the type of transfer is relatively unimportant.

Jan 1, 1993

By P. G. Henderson, G. C. Thompson

The organization and mechanized colliery management of a large by G. C. THOMPSON, B.Sc. (Min. Eng.) (Witwatersrand), M.B.L. (Member), and P. G. HENDERSON, B.Sc. (Min. Eng.) (Pretoria), M.B.A. (Member). Usutu Collieries Limited, at present the largest single producer of coal in South Africa, supplies Cam den power station. and produces 435 000 tonnes per month by conventional mechanized methods from bord-and-pillar workings in three mines. The thickness of the seams averages 2 metres, and the depth below surface varies from 15 to 150 metres. Each mine depends to a different extent on certain common facilities and services. Two of the mines are located on the same coalfield, and their rationalization would possibly be advantageous. Production policy is one of productivity with flexibility. The double-loader system is widely used, and one section at each mine is worked on single shift. Pillar extraction is practised where possible. In addition to lubrication and inspections, planned maintenance of mining equipment consists of sub-assembly replacements and overhauls. Conveyor and tractor/trailer transport is used underground. but trolley-wire locomotive haulage is being considered. The organization is such that co-ordination is relatively difficult, and certain changes could possibly improve the functioning of the engineering and mining departments. Technical and management training is carried out. Long-term planning will make use of a computer programme and will involve the investigation of other mining methods. Five-year and twelve-month plans are prepared, the planning of coal quality being based on the view that the mine and the power station together constitute a system. Control information systems make use of a remote computer terminal located at the mine. An improved integrated system is being investigated.

Jan 3, 1975

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By J. H. Venter

This paper contributes towards the solution of the problem of characterizing the accuracy of estimation of ore quality based on a random sample from the ore bulk.

By W. Spencer

An examination is made of quality standards in castings produced by the South African foundry industry, and some examples are given of the consequences of poor quality to the user. Corrective measures are suggested.

Jan 1, 1981

The Western Cape Branch of the SAIMM recently held a one-day colloquium on the use of artificial intelligence (AI) in process engineering in the I.S. Gericke conference room at the University of Stellenbosch

Jan 1, 1992

Proceedings of the Symposium on Face-end Technology. London, Institution of Mining Engineers, 1981. £25 per copy (members), £ 30 per copy (non-members) including postage. Reviewer: B.C. Alberts This book includes the papers presented at the Symposium, which was held in Harrogate, England, in December 1980.

Jan 1, 1982

Minerals Handbook 1994-95: Statistics and analyses et the world's minerals industry? by P. Crowsons, Basingstoke, Macmillan, 1994 ISBN 0 333 60931 X. £85. Available from Macmillan Direct Ltd., Houndmills, Basingstoke, Hants, RG21 2XS, UK. Review prepared by Theo J. Oosthuizen, Information and Educational Programmes Division, Mintek

Jan 1, 1995

By W. J. Kotzé

Die derde colloquium van die Spesialiste-afdeling van die SAIMM is op 19 November 1980by die Universiteit van Pretoria gehou en is deur sowat 40 mense bygewoon. Dr J. P. Hugo tree as Voorsitter op en heet al die aanwesiges welkom, en stel elke spreker om die beurt aan die vergadering voor.

Jan 1, 1981

By J. H. Fourie

This paper highlights modern practices in ore-treatment plants, with particular reference to the flotation of P2O5 at the plants of the Phosphate Development Corporation (Foskor) at Phalaborwa in the northern Transvaal. The following aspects are covered: design criteria, equipment and personnel, production standards and control. cost control, maintenance, and process development.

Jan 1, 1981

By W. K. Brisden

The SAG Milling Seminar, which was held at Murdoch University in Perth on 30th November and 1st December, 1989, was a very successful technical seminar. Organizer Dr Norm Stockton reported a total attendance of 130, which was higher than the 70 expected: 20 delegates came from the eastern States and the remainder were from Western Australia.

Jan 1, 1990

By B. G. Fordyce, W. B. Parker

A description is given of the methods used in management planning, pit-equipment selection and maintenance operator training, and formal organization of mining personnel.

Jan 1, 1979

Arthur Robert Owen Wiliams died on 18th May, 1989, at the age of 84. ARO, as he was known, was educated at Malvern in England, and graduated from the Royal School of Mines in 1926. He went to South Africa as a Learner Miner with Consolidated Gold Fields at Robinson Deep.

Jan 1, 1989

A General Meeting and Colloquium on 'Motivation and productivity in the mining industry' was held on May 22nd, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 170 delegates and was opened by the President at 09h25.

Jan 8, 1974

By R. W. O. Kersten

The South African Institute of Mining and Metallurgy collaboration with the Chamber of Mines of South Africa, arranged a colloquium to inform mine management of the current state of knowledge on the rockburst hazard associated with geological structures. The Colloquium was held at Mintek on 4th June, 1986, and attracted approximately 240 delegates.

Jan 1, 1986

By B. Strohmeier

An account is given of the use of a computer to control the performance of three ultra-high-powered electric-arc furnaces in Iscor 5 steelmaking plant at Vanderbijlpark, South Africa. Several of the reports and graphs printed by the computer are reproduced.

Jan 1, 1985

By H. L. Monro

Al forward sales are made on the spot market, and are counter productive because they can only lower the price of gold, as one would expect from any additional supply of gold. Hedging against any further fall in the price of gold can be carried out on one of the World's Futures Exchanges in the same way as other commodities.

Jan 1, 1993

By A. Nicotra, E. H. Roux, J. H. du Plooy, D. H. de Jagger, P. De Waal, G. J. van der Linde

This paper reviews the geology, history, current beneficiation practices, uses, marketing, and future outlook of phosphate in South Africa. The vastness of the reserves, and the industry's efficiency and competitiveness in world terms, are highlighted.

Jan 1, 1989