Search Documents

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire in¬juries that occurred in underground coal mines by state during 1990-1999. Table 1 also shows by state the risk rates, employ¬ees' working hours, lost workdays, and coal production. Over¬all, 87 fires occurred in 12 states. Twenty-seven of those fires caused 34 injuries (the yearly average was 8.7 fires and 3.4 injuries). One fire and one injury involved a contractor. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations followed by 13 mine/section sealing/flooding/CO2/N2, gas injections. The Ewhr value was 1,003 x 106 hr (In = 0.007), the CP value was 4,008 x 106 st (Frr = 0.022), and the LWD value was 208. Virginia had the most fires (15 fires and 7 injuries). Pennsyl¬vania had the most fire injuries (12 fires and 9 injuries), fol¬lowed by Kentucky (12 fires and 6 injuries), and Alabama (12 fires and 4 injuries). Among these states, Alabama had the highest fire risk rate value (Frr = 0.073), whereas Pennsylvania had the highest injury risk rate value (In = 0.016). Table 2, partly illustrated in figure 2, shows by time period the number of fires, fire injuries, risk rates, employees' working hours, lost workdays, and coal production. The number of fires and fire injuries show a decrease followed by an increase during the five time periods (see table 2 and figure 2). This was ac¬companied by a decline in employees' working hours throughout the periods and an overall small decrease in coal production. The In and Frr values follow patterns similar to those shown by the fire and injury values. By comparison, data from Pomroy and Carigiet [1995] show that during 1978-1992 a total of 11 states were involved in 164 underground coal mine fires (yearly average, 10.8) with 43 injuries (yearly average, 2.9) and 27 fatalities (yearly average, 2; however, the 27 deaths occurred during a single fire caused by an overheated air compressor [MSHA 1984]). The CP value was 5,340 x 106 st (yearly average, 356 x 106 st) (Fn = 0.031). Data on employees' working hours and injury risk rates were not available. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables during 1990-1999. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire injuries that occurred in underground metal/nonmetal and stone mines by state during 1990-2001. Table 1 also shows the injury risk rates, employees' working hours, and lost workdays. Overall, 65 fires occurred in 20 states; these include 2 fires and no injuries for contractors. Six of the fires caused nine injuries. The yearly average was 5.4 fires and 0.75 injury. Forty-one fires with 2 injuries occurred in metal mines, 14 fires with 7 injuries occurred in nonmetal mines, and 10 fires with no injuries occurred in stone mines. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations. The Ewhr value was 260 x 10° hr (Irr = 0.007), and the LWD value was 83. Idaho had the most fires (eight fires and no injuries), followed by Louisiana (seven fires and two injuries), Michigan (six fires and six injuries), and Missouri (six fires and no injuries). Of these states, Michigan had the highest injury risk rate value (Irr = 0.146). Table 2, partly illustrated in figure 2, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires during the six time periods show an increase during the fourth period followed by a sharp decrease during the fifth period and a sharp increase in the last period. The number of fire injuries show an increase followed by a decrease during most of the periods, accompanied by a decline in employees' working hours during most of the periods; an increase is seen during the third and fourth periods. The In values follow patterns similar to those shown by the injury values. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables related to fires for 1990-2001. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

By J. B. Janus

This Bureau of Mines publication updates a series of reports on the quality of coal purchased under specifications for Government use. Listed are analytical data on the composition and quality of tipple and delivered samples of coal collected during the period July 1975 through September 1976.

Jan 1, 1977

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

By R. F. Waters

The Bureau of Mines developed laboratory-scale processes to recover sodium phosphates and metal values from waste sludges generated by the phosphate treatment of automobile and appliance components. After treatment of the sludge with NaOH, followed by coke or hydrogen reduction and sintering, zinc and lead were recovered as fume; the sinter was separated by leaching into a metallic product, chiefly iron and nickel, and high-purity disodium or trisodium phosphate.

Jan 1, 1971

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

By J. Hanslovan, R. H. King

An investigation of the feasibility of shielding low-voltage trailing cables in underground coal mines is described. Both laboratory and under¬ground installation results are presented. The main objective of shielding is to reduce the electrical shock hazard; however, several problems will be encountered by mine operators who install shielded cables. Parameters related to such items as purchasing, splicing, troubleshooting, safety, and reliability are discussed. Some of these problems can be minimized by changes in cable constructions and shuttle-car reeling-device components. Both SH-C and SH-D constructions are considered.

Jan 1, 1979

Provide a means for reliable in situ stress change measurements in soft, friable geologic materials under high stress. Background Effective mine design requires a knowledge of changes in rock stress generated by a mining operation. In situ stress measurement can provide a means of obtaining this knowledge from an active mine for the ultimate purpose of design verification and analysis. The Bureau of Mines has designed and tested a device for measuring changes in rock stress-the borehole platened flatjack (BPF). It has found application in investigating stress anomalies due to geologic structures, stress concentrations from multiple seam interaction, and stress abutments from pillar retreat and longwall mining.

Jan 1, 1990

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In 1981, the combined value of these commodities accounted for about $11.6 million,2 over 85% of the total value of mineral output. Production of cement, sand and gravel, and quarry products increased substantially above the 1980 level. Mining bated on gold production was decreasing, and employment in the industry was declining. The better grade deposits in the one active mine were worked out, and only another 10 years' production at current rates was estimated to remain. While the high world gold price of 1979-80 led to intensive exploration, there has been little sum.

Jan 1, 1983

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

Provide a coalbed methane data source for industry use in mine planning. Approach Coalbed methane data have keen collected and formatted into a computer implemented data base with software developed for storage, retrieval, and generating files of selected data in response to information requests and for statistical analysis of relationships among various coal parameters. How It Works Coalbed methane data is obtained by the Bureau's direct method test on exploration coal cores. The test involves sealing fresh coal cores in desorption canisters and periodically bleeding the gas into a water-filled, graduated cylinder to measure the volume of gas released. Coalbed methane data collected over the past 9 years have been entered into a computer-implemented data base for efficient retrieval and statistical analysis. Data base processing is accomplished with a commercially available storage, sorting, retrieval, and report writing software package (Datatrieve 11). Information requests from the coal industry are processed with the system, and the data in the desired output format am printed and forwarded to the requestor. Information such as coalbed name, location (state and county), depth of sample, gas content, and coal rank are available from the system. The data can be used for

Jan 1, 1982

By A. N. Styler

As part of its water-jet assisted rock cutting research, the Bureau of Mines has initiated a study into the mechanism of rock fragmentation by water-jet-assisted mechanical tools. The objective of this research is to increase coal extraction efficiency by seeking an improved understanding of the synergistic relationship between mechanical cutters and water jets, enabling the design of more effective cutterheads. Rock chips collected during laboratory traverse speed jet-assisted cutting tests were analyzed with respect to the size distribution of the chips and the forces measured during cutting. As the water-jet pressure was increased, the size distribution of the product became coarser with V-face type cutting tools producing less fine material than conical cutting tools. Fracture mechanics theory accounted for less than 10 pet of the energy consumed during fragmentation of the rock. The energy consumed by processes other than rock breakage decreased with the use of water jets and increasing advance rate.

Jan 1, 1987