Search Documents

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

Empirical methods involve the scientific interpretation of real-world experience. Many problems in ground control lend themselves to an empirical approach because the mines provide us with plenty of experience with full-scale rock structures. During the past 10 years, powerful design techniques have emerged from statistical analyses of large databases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. In the process, our practical understanding of pillar behavior has been greatly enriched.

Jan 5, 1999

By B. J. Moore

This publication contains routine analyses and related source data for 419 natural gas samples from 22 States collected during calendar year 1964 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/ Six previous publications have been made to present the results of 6,293 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1964. The first three, Bulletins 486,5/ 576,6/ and 617,7/ contain analyses and related source data on 5,214 gas samples collected from

Jan 1, 1966

Coal mining in Indiana is limited to the south-western portion of the state, with coal currently being recovered in 19 counties. The coal-producing area of the state covers approximately 6,500 square miles. Although most of the coal in Indiana is recovered by surface mining methods, a small percentage is recovered through underground mining. To date, 40 percent of the known coal reserves have been removed. Indiana has about 33 billion tons of identified coal reserves, of which approximately 17 billion tons are recoverable using current technology. Of this recoverable coal, about 15 billion tons are recoverable by underground mining and 2 billion tons are recoverable by surface mining methods. The State of Indiana has regulated the environmental impacts of coal mining since 1941. Indiana was the second state in the nation to pass legislation requiring mined land reclamation. Its SMCRA regulatory program was approved July 29,1982, and its Abandoned Mine Land Program was approved July 29, 1982.

Jan 1, 1992

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By Richard S. Gaps

The Derby and Alexander Claim, located within the Tunnel Ridge Wilderness Study Area (WSA), has placer gold resources. No lode deposits are known within the area, but lode gold deposits are found within 1 1/2 mi of the WSA. In additon, rock units which contain lode gold deposits north of the WSA are found within the northern portion of the study area. INTRODUCTION The Tunnel Ridge Wilderness Study Area (WSA), CA-030-402, encompasses 4,623 acres of BLM administered public land in Trinity County, California, about 35 mi west-northwest of Redding (fig. 1). Major access to the Tunnel Ridge vicinity is by U.S. Highway 299. Ac-cess to the WSA boundary is by a secondary paved road from Junction City and several light duty dirt and gravel roads (fig. 2). The WSA is on the southwest slope of Weaver Bally Mountain. The topography is rugged with moderate to steep slopes; elevations range from about 1,600 ft to 5,900 ft.

Jan 1, 1983

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig. 1). The average fuel requirement per barrel of crude oil refined has remained virtually stationary for the past 3 years. Thus in 1937 the average was 562,000 B.t.u., in is it rose to 567,000 B.t.u., and in 1939 it declined to 557,000 B.t.u. she largest gains in fuel economy cane a decade or so ago on the widespread introduction of heat exchanges and pipe stills. In recent years many successful innovations in heat saving have been adopted, but the combined effect of those is completely masked by the degree to which the capacity is utilized. Some heat requirements are relatively inelastic, so the average consumption per barrel of crude oil refined tends s to increase when the operating ratio (crude runs divided by capacity) declines and vice versa. In 1939 crude runs to stills increased 6 percent (from 1,165,015,000 barrels in 1938 to 1,237,840,000 in 1939) compared with a decline of about 2 percent in 1938. The operating ratio in 1939 was 82 percent compared it's 78 percent in 1938.]

Jan 1, 1941

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East, providing more than 80 % of the region's foreign exchange. In 1992, the 15 countries that constituted the region accounted for 29.5 % of world crude petroleum output, 20 % of world natural gas plant liquid production, and 5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. A fairly wide range of non fuel minerals is also produced in the region. The most significant are boron minerals, bromine, chromite, gypsum, phosphate rock, potash, strontium, and sulfur. However, the variety of minerals produced, output levels, and the size of the overall non fuel mineral economy of the region is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, was first in world production of run-of-mine boron minerals, second in strontium behind Mexico, and fourth in pumice. It was also a significant world producer of chromite, magnesi'lm compounds, mercury, and sodium sulfate. Turkey was also the Middle East's largest cement and steel producer. Iran continued to expand output of most mineral commodities following the war with Iraq from 1980 to 1988. It was a significant world producer of gypsum and strontium and on its way to becoming a major iron and steel producer in the region. Despite a very small domestic mineral industry, Israel was second in world production of bromine and a significant producer of phosphate rock and potash. In terms of processed minerals, Israel was a major world diamond cutting center and exporter of cut diamond. Jordan ranked sixth in world production of phosphate rock. Saudi Arabia was eighth in world production of sulfur.

Jan 1, 1994

By L. R. Burdick

Anthracite barley is considerably cheaper than rice. Its use, therefore, is attractive from a cost standpoint, - but its smaller size (through 3/16 inch over 3/32 inch round-mesh screen) makes it more difficult to use on some equipment when fairly high combustion rates are necessary to carry plant loads. Tests wore made in one plant to determine the performance of rice and various types of barley on a chain-grate stoker in a two-arch refractory furnace. In general, the efficiency and capacity increased with increased fuel size and volatile content. This performance is presented in tabular and curve form, together with a short review of the ignition and burning process on chain-grate stokers and a discussion of the operating procedures and limitations during the tests. In this particular installation, higher combustion rates and efficiencies could have been obtained with barley if the grate links had been designed for more uniform air flow through the grate surface. Careful maintenance and operation are particularly necessary for satisfactory results with barley on equipment not especially designed for its use.

Jan 1, 1950

By J. W. Thompson

MINERALS OWNERSHIP AND POSSESSION. The owner of minerals under a conveyance from the surface owner does not lose his right or his possession by mere nonusage of the minerals. McBeth v. Wetnight (Indiana), 106 Northeastern, 407, p. 410, October, 1914. QUIETING TITLE TO MINERALS-PLEADING. A complaint in an action to quiet title to minerals and to the min- eral rights in certain land is insufficient in the absence of a direct allegation of possession, although it avers that the plaintiff from the time of receiving the conveyance assessed the mineral interest for taxes each year and paid the taxes thereon and exercised various acts of ownership of such mineral interests, in that he caused test pits to be dug on the land for the purpose of exploring the minerals and ascertaining their quality and extent, in going upon the land and looking after them from time to time, and that he accompanied or caused his agents to accompany prospective purchasers of such mineral interests and exhibited the same to such prospective pur- chasers in efforts to sell them. Fowler r. Alabama Iron & Steel Co. (Alabama), 66 Southern, 672, p. 673, Novem- ber, 1914. SALE BY MARRIED WOMAN-VALIDITY. A conveyance by a married woman of the mineral rights in certain described land is void where she had previously conveyed the land to another grantee who had acquired title by adverse possession under the deed.

Jan 1, 1915

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.