Search Documents

By David Bequette, Ray D. Peterson, Cynthia K. Belt

"With a need to cut production costs in the metals industry, cost savings from energy efficiency improvements are critical. Opportunities can be found by reviewing furnace systems and practices so that the melting and holding processes operate at the highest energy efficiency. Many of the changes can be implemented with a minimum of expense or capital investment. This paper will review several low cost methods to optimize energy efficiency on reverberatory melting or holding furnaces. These five methods (furnace utilization, idle procedures, fire rate, controls, furnace pressure) will be explained and information given to implement these changes. Included are several rules-of-thumb and benchmarks for aluminum reverb furnaces.IntroductionEnergy can be a significant portion of the total manufacturing costs for metals and materials manufacturing involving thermal processing such as heat treating, melting, and high temperature processing. Natural gas prices have dramatically varied over the last few years. While no one can foresee the future, prices are expected to increase from the current low prices. More recently, emphasis is being put on the reduction of greenhouse gases with the potential of additional costs to industry.One of the first steps in an energy management program is to measure the energy usage of the process [1]. The results are typically understood in relation to the mass melted in kWh / mT [BTU / lb]. For the purposes of this paper, furnace energy efficiency is calculated over a month or even a year and thus includes hold times. This efficiency is typically different from the values quoted by furnace manufacturers. Those values are for limited short term tests at highutilization.Once you know the performance for your furnaces, these should be compared to industry benchmarks. For aluminum melt furnaces with cold air burner systems, a benchmark value or goal is 1800-2000 BTU/lb [1160-1290 kWh/mt], though some of the best have reached 1600 BTU/lb [1030 kWh/mt]. Furnaces with regenerative burners can attain 1100-1200 BTU/lb [710- 775 kWh/mt]. There are some designs of multi-chamber furnaces or oxygen furnaces that have improved on these numbers, perhaps as low as 950 BTU/lb [615 kWh/mt]. Typically, as the degree of sophistication and energy efficiency of the furnace increases, so does the cost."

Jan 1, 2010

By A. M. Salomon de Friedberg

With respect to impurities, HBM&S' copper smelter, located in Flin Flon, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Flon is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.

Jun 1, 1993

By A. M. Salomon de Friedberg

"With respect to impurities, HBM&S' copper smelter, located in Flin Ron, Manitoba, is in an unusual position. In addition to the usual concerns, the fact that copper and zinc production at Flin Ron is closely integrated results in the unique situation where feed to the copper smelter typically contains 7% to 8% zinc. This paper discusses the ramifications to copper smelter operations resulting from the marriage of HBM&S' metallurgical plants. Distributions of impurities (specifically Zn, Pb, Ni, As, Bi, Sb, and Cd) are presented and operating practices designed to reduce the impact of impurities on anode copper quality are detailed.IntroductionHudson Bay Mining & Smelting Co. Ltd. (HBM&s), has been operating its metallurgical complex located in Flin Flon, Manitoba, since 1930. The smelter and zinc plant were originally separate entities with respect to production. The smelting operation consisted of traditional multiple-hearth roasters, a reverberatory furnace and Peirce-Smith converters. The zinc plant also utilized multiple hearth roasters and then followed with sulphuric acid leaching, purification and electrowinning. The zinc plant also recovered cadmium from a separate purification/electrowinning circuit.The two plants operated essentially independently of each other until rising zinc levels in the copper concentrate and large stockpiles of zinc-rich leach residues prompted the construction of the fuming plant in 1949. The smelter used pulverized coal to reduce zinc oxide present in the reverb slag and then captured the resulting zinc bearing fume in the fuming plant baghouse. The fume was sent to a separate ""oxide roaster"" in the zinc plant where it was first roasted to remove halogens and then leached to recover the contained zinc. This oxide fume became a major source of feed to the zinc plant accounting for roughly one quarter of the total zinc production. Furthermore, through the smelter's treatment of sulphide leach residue, both copper and zinc recoveries were improved for the over-all complex."

Jan 1, 1993

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By W. M. Ross

AMONG the comparatively few A radical changes in mining equipment in recent years is the introduction and use to an ever greater degree of detachable bits for rock drills. Just how great the possible field for economic application of this innovation is, and to what ex- tent detachable bits are used instead of the conventional type of drill steel, are matters of conjecture. Just as a rough approximation, one might conceive that at least three-quarters of the drilling done in mines today could better be performed by steel with detachable bits, instead of only about one-quarter as at present.

Jan 1, 1939

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By M. Le Roux, Q. P. Campbell, M. Fofana

The determination of densimetric information to predict coal washabilities is an important step in characterising the feed material, as well as the performance of operating plants. However, traditional methods like float-and-sink analysis are hazardous and time-consuming. This is especially true for finer particle size ranges, where very long settling times are required in a medium. De Beers Technologies recently developed a density analyser, known as the RhoVol, for use on diamondiferous kimberlite. Operating over size ranges from 25 mm down to 3 mm, it can determine the mass, volume, density, size and shape of all the particles in a given population and is thus able to provide information about the densimetric distribution on a single particle basis. A study was carried out to compare uncalibrated and calibrated RhoVol results to densimetric and size data obtained using traditional zinc chloride float-sink procedures, for three different coal samples in the size range 3 mm to 8 mm. The results indicate that the RhoVol can be used to provide simple, rapid and safe size-by-washability information for coal, provided proper pre-calibration is done, mainly to account for the effects of particle porosity in the density determination. Keywords: Coal washability determination, RhoVol, densimetric curve

Jan 1, 2020

By V. T. McLemore

New Mexico Bureau of Geology and Mineral Resources (NMBGMR) has been collecting data on uranium mining districts, mines and mills since it was created in 1927 and has converted years of historical data into a relational database that can be imported in ArcMap. The database includes information on mining districts, mines, mills and geochemistry, as well as photographs and bibliographic resources. The available data includes location, production, reserves, geologic, geochemical, resource potential and other data. The National Uranium Resource Evaluation (NURE) stream-sediment data provides geochemical analyses for >27,000 samples collected in New Mexico during the 1970s. The NURE hydrogeochemical data provides analyses of water samples. ArcMap includes the location of individual ore bodies as polygons and incorporates the mines and NURE data as individual site locations. The purposes of these databases are to provide computerized data that will aid in identifying and evaluating resource potential, resource development and management, production and possible environmental concerns, such as physical hazards (i.e., hazardous mine openings), indoor radon, regional exposure to radiation from the mines, background geochemical data and point sources of possible pollution in areas of known mineral deposits.

Jan 1, 2010

By D Misra, R Ganguli, S Bandopadhyay

The objective of this paper is to assess the accuracy and applicability of recent state-of-art methods such as the machine learning algorithms (MLA) for mineral resource estimation. Conventional methods such as geostatistics have been predominantly used in the mining industry for this purpose with varying success. Recent advances in the use of MLA have provided a fresh approach to obtain improved accuracy in the estimation of mineral resources. Two MLA methods: the neural network (NN) and the support vector machine (SVM) have been used to estimate a polymetallic ore deposit in Alaska.The general characteristic of SVM and NN emphasises the fact that they can approximate any multivariate non-linear relation among variables. Although neural network models are able to capture the nonlinear spatial relationships that may be present in the data, they are usually difficult to optimise under sparse data settings. Of the various NN alternatives, despite their effectiveness, the model selection and estimation process is typically difficult as it involves solving complex integration and optimisation of parameters. In support vector modelling (SVM), estimating of parameters involves optimisation of a convex cost function. The working principle of SVM makes it robust against noisy and extreme value data. At the same time, it can capture the spatial distribution of ore grade more effectively with careful modelling and selection of SVM parameters.The outcome of the MLA methods were compared to those of the geostatistical ordinary kriging (OK) application to study their generalisation ability. The comparison was made using the following goodness of fit criteria: mean-squared error; mean absolute error; mean error; and coefficient of determination. The results indicated that the MLA methods may improve the predictability of ore deposits and thereby reduce the inherent risk in mineral resource estimation.

Sep 26, 2011

By P. K. Kaiser, C. D. Martin, F. Amann

"This article focuses on the uniaxial compressive strength (UCS) of homogeneous and heterogeneous rocks. Critical factors impacting the UCS of rocks are reviewed and then separate assessments of UCS data from homogeneous and heterogeneous rocks are presented. The variability (coefficient of variation) of UCS test results for homogeneous rocks is found to be generally <25% while for heterogeneous rocks the variability is >35%. Failure mode variation is found to be the cause of the variability of UCS test results in heterogeneous rocks. Empirical engineering design methods that use UCS as an input parameter are discussed and suggestions are provided for selecting appropriate UCS values.INTRODUCTIONThe UCS is one of the most commonly used rock engineering parameters whether for rock mass classification or for strength determination. The mean UCS and its variability are often assumed to represent a reliable rock material property. For the reasons discussed in this article, UCS is rarely representative of the intact rock UCS. The UCS test simply records the collapse load during uniaxial loading of a cylindrical specimen. As suggested by many, the UCS is an index rather than a unique engineering parameter. The UCS is thus a proxy for rock strength which depends on the loading rate (e.g., Bieniawski 1967), specimen geometry (e.g., Hudson et al., 1971), specimen size (e.g., Bieniawski 1968), and many other factors. Furthermore, the UCS is not the same as the Hoek-Brown strength criterion parameter sci.There are differences in opinion on what is commonly considered to be ‘intact rock’. When sampling ‘intact’ pieces of core from drillholes crossing blocks of rock bound by block forming discontinuities, samples will be ‘intact’ but some samples will be veined, others will be damaged, and others will be neither. According to Hoek (1983), intact rock pieces are “the unfractured blocks occurring between structural discontinuities in a typical rock mass” and the sci parameter for intact rock is determined using the fitting procedure proposed by Hoek and Brown (1997) based on the data requirements outlined by Hoek (1983). Studies (e.g., Bewick and Kaiser 2014; Kaiser and Kim 2014) have shown that independently determined UCS and sci values for the same rock type are not equivalent. Thus, UCS data cannot be used as a replacement for sci."

Jan 1, 2015

By Hatch, A. Reple, W Valery

The mining industry is facing declining feed grades which require the mining and processing of larger volumes of material per tonne of product. Pre-concentration aims to remove barren material at as coarse a particle size and as early in the process as possible to reduce processing costs, energy consumption, water losses, and greenhouse gas emissions while increasing production and profitability. This may be achieved using bulk ore sorting—the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor. This paper evaluates the technical and economic viability of bulk ore sorting for the PanAust Phu Kham copper deposit in Lao PDR. Bulk ore sorting technology is described briefly along with discussion of appropriate sensor and diversion systems for the Phu Kham operation. To evaluate the economic implications, the actual mined material and costs from 2014 were used as the base-case. Sampling data was not available; therefore, the ore grade variability that would feed a bulk ore sorter was estimated using geo-statistical tools based on mine grade control data. The sorter performance when treating this material was simulated considering the accuracy of the sensor measurement and errors associated with material diversion. The impact on inferred cash flow was estimated for several different scenarios considering the additional costs for sorter operation and reject handling. The evaluation demonstrated that bulk ore sorting at Phu Kham has the potential to increase the amount of metal in product and/or reduce processing plant throughput (and costs) to improve the annual inferred cash flow for the conditions investigated. The sorter is the gatekeeper – only material above the cut-off grade (value-adding) reports to the processing plant; no waste dilutes the feed. Likewise, above cutoff grade material is not lost to waste; preventing lost revenue.

Jan 1, 2016

By C Smith, R I. Maczkowiack, P D. Erskine

Open cut coal-mining has been conducted in the Bowen Basin region of central Queensland for almost five decades, and has disturbed an estimated area of 140 000 ha of agricultural land until 2011. Approximately one-third of the area disturbed by mining has been rehabilitated to pastures or bushland. However, none of the rehabilitated land has yet been assigned a specific end-use. This research project develops an approach for assessing end-use risks for the regionÆs mined land, and develops risk assessment models for selected end-uses. First, a web-based survey of stakeholders was used to identify risks to be assessed. The risks identified were surface erosion, subsurface erosion, bushfires, weeds and feral animals. The survey also identified possible end-uses of bushland and grazing. Second, conceptual risk models were developed based on the risk assessment concepts of likelihood and consequence specified in the Australian and New Zealand risk assessment standards. Likelihood was modelled using site characteristics and management factors that influence the occurrence probability of risks (eg surface erosion), while consequence was modelled using a set of site condition indicators and condition thresholds (changes in root-zone water-holding capacity, soil erodibility, vegetation ground cover and soil organic matter and transition probability to a non-preferred ecosystem type).The factors influencing likelihood and consequence for each risk have been integrated using Bayesian networks. The next step in model development is to parameterise the Bayesian networks using existing equations, empirical datasets, or expert opinion where data are not available. The parameterised models will be used to assess grazing and bushland end-uses against erosion, bushfire, weed and feral animal risks for rehabilitated mined land sites, with the purpose of identifying the relative risks associated with each end-use, and the landform design specifications and land management practices under which end-use risks are minimised.CITATION:Maczkowiack, R I, Smith, C and Erskine, P D, 2012. Risk assessment models for post-mining land use, in Proceedings Life-of-Mine 2012, pp 33-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By John C. Smock

The rich deposits of magnetic iron-ore in the Highlands of northern New Jersey attracted the attention of iron-workers at the time of the earliest settlements in that region. The outcrops of the oreshoots at the Dickerson mine, at Mount Hope, and at Hibernia, in Morris county, and at Ringwood, in Passaic count,y, which were doubtless such as would lead to discovery, location and development of nearly all the large iron-mines in that part of the State, appear to have had their beginnings where the ore cropped out on the surface or where it was scarcely concealed by a thin mantle of earth. In the early history of New Jersey iron-mining, the careful explorations and surveys made by the agents of the famous London Com-

Jan 1, 1892

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world&apos;s shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada&apos;s mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, &apos;the Non-Metallic Minerals&apos;, compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term &apos;Industrial Minerals&apos;, when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term &apos;Industrial Minerals&apos; is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By Zhang-Guang Gao, Ming-Mei Zhu, Rui-Rui Zhao, Chao Jiang

This paper focuses on the CaO-SiO2-FeO-MgO-MnO-P2O5 slag system that represents the major components of dephosphorization slag in BOF. Phosphorus distribution between 2CaOSiO2-3CaOP2O5 Solid Solution and Liquid Slag were analyzed by FactSage. The effects of slag content, basicity on the distribution ratio of P between the solid solution phase and the liquid phase (LP) and the percentage content of P in solid solution phase and liquid phase have been discussed. The results show that, with the increase of basicity, LP (wt%) decreases until the basicity reaches 1.9, then it turns to increase. LP (wt%) increases gradually with the increasing amount of FeO or P2O5.

Mar 1, 2017

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By A. H. Lang

"The Cordilleran region of western Canada includes most of British Columbia and the Yukon and pares of Alberta and the Northwest Territories. The western part of this region was for about 50 years the principal mineral producing area of the Dominion. It lost this distinction in 1907 when production from the mines of the Canadian Shield took the lead, but it continues to provide about 15 percent of the total Canadian production. In 1945 the total mineral production of British Columbia and the Yukon was valued at $65,302,900, of which about 80 percent was derived from metals.This paper is intended to serve as an introduction co the more derailed Cordilleran papers. Part I includes a brief synopsis of the complex geology and diverse types of mineralization in the region and Parr II collates the main structural principles exemplified in the derailed papers, and draws some conclusions regarding the application of this information to prospecting."

Jan 1, 1954

By Forrest A. Kerr

Northern British Columbia is a term which probably conveys to various individuals quite different meanings. To the average person it signifies an area of indefinite size and indefinite position which may start at Prince Rupert, Stewart, or somewhere else, and end at Alaska or .the Yukon. Many people, in their conception, fail to encompass in their mind&apos;s eye that vast tract of land lying ~o the east of the panhandle of Alaska. Few realize that the area north of an east-west line through Stewart represents more than one-third of the Province and is, of course, the part most appropriately designated as northern British Columbia. This section, more especially the northernmost 100,000 square miles, from political, geographic, and economic viewpoints stands isolated perhaps more than any other part of British Columbia. Unlike the rest of the Province, it has no coast line, being cut off from the Pacific ocean by a narrow strip of Alaska. It is bounded on the north by the Yukon, and on the east by Alberta. In the south this northernmost 100,000 square miles is limited by a divide of rugged mountainous country separating the drainage basins of the Stikine and Liard rivers from those to the south.

Jan 1, 1929