Search Documents

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By J. B. Elizondo

This paper, which describes mining methods and practices at the Piokee mining unit and the Piokee expertmental mining project of The Eagle-Picher Co. in northeast Oklahoma, is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Piokee unit, comprising the Piokee, Rowe, Lucky Syndicate, and parts of the Netta White and Otis White leases, is in the SW1/4, W1/2NW1/4SE1/4, and W1/2SW1/4SE1/4 sec. 17, T. 29 N., R. 23 E., Ottawa County, Okla. (figs. 1 and 2), The 200-acre tract is adjacent to the town of Picher and near the heart of the Picher field of the Tri-State zinc-lead mining district.

Jan 1, 1959

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By John Nagy

To facilitate increase in the rate of coal production the Bureau of Mines conducted a study several years ago, on the basis of which the allowable charge limit for permissible explosives in single-hole blasting was raised from 1.5 to 3.0 pounds. Further demands for accelerated production led to consideration of multiple blasting in coal, a practice that is deemed hazardous and is not permitted by most States in this country. In multiple blasting, 10 to 20 pounds of explosive or more may be detonated in a coal face within a fraction of a second, which might result in blown-out or blown-through shots with possible ignition of gas or coal dust. As experimental evidence was lacking, in January 1949 an investigation was undertaken in the Experimental coal mine at Bruceton, Pa., principally to study and compare with single blasting the condi-tions under which simultaneous multiple blasting and particularly multiple short-delay blasting may be practiced without danger of igniting gas or coal dust in mines. The first report on this subject was presented at the last international conference of mine safety research. Since that time numerous additional experiments have been made; because of other pressing problems the work has been brought temporarily at least to a conclusion. This paper is the second report on the problem. It does not contain a detailed description of all test conditions and test arrangements, many of which were described 2 years ago in part 1 (now available as Report of Investigations 4868), but the conclusions are based on the entire study. A more complete review, which will incorporate data from the entire investigation, is being prepared as a Bureau of Mines bulletin. Up to the present time, short-delay blasting of coal in commercial mines has been introduced only experimentally in Washington and in a few mines elsewhere. If the system is adopted more generally, new problems may arise, and the study may have to be reopened.

Jan 1, 1952

By B. M. Harra, O&apos

Zinc smelting is frequently termed a backward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, low-unit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pounds of ore. The diameter of the retort is limited by the time required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, or producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser attached to one end of the retort, where it condenses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls and of the ore charge itself, the heat efficiency even of the most modern regenerative furnaces is only about 12 per cent. The retorts have a short life, 30 to 60 days, at the high temperature required; zinc

Jan 1, 1923

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning's equation. To the authors' knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

By Daryl R. Tweeton

This Bureau of Mines publication ill scribes present practices of making injection wells for in situ uranium leaching. Casings, screens, drilling fluids, coring, logging, cementing, and developing are discussed with the objective of aiding those who are starting an in situ leaching operation. Improper choices of materials or techniques can result in wells that are either useless or wells that have an undesirably high resistance to injection. Important factors include careful selection of screen slot size, use of logs for choosing the cementing basket depth, proper cementing techniques, and careful choice, use, and flushing of drilling fluids. The information was obtained through observation of well construction and through discussion with in situ leaching companies, drillers, and suppliers.

Jan 1, 1978

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By John D. Watson

The results of extensive field tests of a new and powerful method of hard rock excavation are presented in this report.* The method, known by the acronym REAM (Rapid Excavation and Mining), employs high velocity, smooth bore cannons to efficiently deliver energy to the rock and has been demonstrated for underground tunneling, drilling, surface benching, scaling, and secondary breakage in hard granitic rock at the Hope Valley Mine test site in California. Solid projectiles made from inexpensive materials such as concrete or steel, and weighing from 8 to 12 pounds, are launched by conventional high speed cannons and impact the rock at velocities of 5000 feet per second--an impact energy of about 4 million foot pounds (Figure 1). The energy applied at peak pressures of nearly 2 million psi over a period of tens of microseconds breaks down the rock by a complex mechanism of crushing, spalling, and initiation and propagation of fractures produced by the interaction of successive impacts and free surfaces. The main objective of the tests during 1973 was a demonstration of controllability of the underground operation of a silenced cannon. To accomplish this objective a 90-mm cannon

Jan 1, 1974

By J. T. Popp

This Bureau of Mines study reviews the geological factors that affect methane in the Beckley coalbed in southern West Virginia, including overburden, coalbed structure, type of and changes in lithology above and below the Beckley coalbed, and presence of fractures in the coal and rock adjacent to the Beckley. Depending on the depth, the Beckley coalbed emits from 216 to 520 ft3 of methane per ton of coal mined, and the Bureau estimates that methane emission in a deep, extensively developed mine in this area may exceed 3,000 ft3 per day per ton of coal mined. Average face cleat and butt cleat trends in the Beckley coalbed measured underground are N 33° W and N 53° E, respectively. Close cleat spacing con¬tributes to the friable nature of the Beckley and provides easy movement for methane and water. Because rider coals, splits, and carbonaceous shales may contribute methane to mine emissions, predictions of methane emission based on gas content of the Beckley coalbed alone may be conservative. Beckley coalbed reserves in the study area are 234 million tons. The gas content of the Beckley coalbed averages 407 ft3/ton, and the coalbed gas reserves are 108 billion ft3.

Jan 1, 1976