Search Documents

By Julius G. Chang

Against the receding background of the October stock market crash and the December overhang of inventories, the economy began with a shaky start in 1988. As 1988 began, the Administration's estimate of real growth for 1988 had just been reduced from 3.5% to 2.4% and economists and other ob-servers were concerned that the expansion that was 5 years old might be near the end and that a recession might be around the corner. The ensuing moderately strong economic activity, however, belied all the negative signals that were evident earlier, and the real GNP continued to grow at an estimated 2.3% annual rate during the first quarter of 1988, extending the ongoing recovery into the sixth year (table 1.). The relatively accommodative policy of the Federal Reserve Board (the discount rate was cut by 0.25% in January), a strong performance by the export sector, and the revival of consumer spending were major forces underlying the economic strength. But as the quarter drew to a close, signs of tight capacity utilizations were apparent in many of the export and capital goods sectors, including textile, chemical, plastic, metal, and machinery. Employment was at a record high level while the unemployment rate was close to a historical low. Prices were rising at a faster pace than those of 1987, and the dollar resumed its slide after a brief recovery in January and February. These factors gave rise to the fears of higher inflation. Long-term interest rates increased, casting a pall over the prospect of a robust growth for the rest of the year.

Jan 1, 1988

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By S. A. Montague

In spite of the many new insulating materials, both synthetic and manufactured, that have been put on the market since the end of World War II, and notwithstanding the many millions of dollars applied to the development of synthetic mica, natural block mica1 is still a most indispensable insulator in various electronic components. It will remain so, barring some spectacular break-through in research that might provide a substitute fully acceptable as a replacement for mica in all of its superior properties. But this is not to say the future for mica is assured, or free from serious problems. Technological advances have created problems requiring a solution to be found if future requirements are to be filled.

Jan 1, 1962

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By A. F. Marques

The Azores islands are located on a triple junction where the American, African (AFR), and Euroasian (EUR) plates meet. The Mid-Atlantic Ridge (MAR), oriented N-S, represents two branches of the T; an E-W branch defines the EUR/AFR boundary called the Terceira Rift. The nature and structure of this plate boundary, as well as the dynamics of the interaction of tectonics and volcanism remain unconstrained. The Azores plateau is seated on a mantle domain of anomalously low seismic S-wave velocities, and gravity and geoid anomalies, where the apparent thick crust is thought to relate to larger degrees of melting initiated at greater depths [1]. The cause of these anomalies is controversial but many authors consider the presence of an anomalously hot/wet enriched mantle probably supplied by a plume [2]. The geochemistry of the subaerial and most submarine lavas from the plateau reinforces the plume model beneath the Azores [3-4]. The origin, size and present location of the plume is under debate but an area near Terceira is the favoured plume centre [5]. [ ] SEAFLOOR HYDROTHERMAL SYSTEMS IN THE AZORES AREA (36ºN ? 40ºN) More than 150 active and fossil hydrothermal systems are known in the oceanic seafloor [6]. Many more are yet to be found on vast oceanic areas that haven?t been explored [7]. Ever increasing knowledge shows that modern seafloor hydrothermal systems can be hosted in felsic to ultramafic rocks, vary in size and shape and exhibit diverse amounts of sediment cover

Jan 1, 2011

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

A review of historic mining information and geological literature pertaining to the Alpine Mine, Lyell Goldfield has been completed. As a result of this work the Alpine reef is inferred to be associated with an upright anticline with a sub-horizontal axis. Structural profiles prepared from limited underground data indicate that the reef is subparallel to the eastern limb of the anticline and cuts across the western limb. Reassessment of structural mapping completed by the New Zealand Geological Survey indicates that Greenland Group metasediments within the Lyell Goldfield are folded into a series of opposed assymetic folds with sub-horizontal axes. It is suggested that the anticline which harbours the Alpine Reef is located on the axis of a synclinorium. Along the western limb of the synclinorium the subsidiary folds have steep west dipping limbs and shallow east dipping limbs (western sense of assymmetry) whereas shallow west dips and steep east dips are typical of the eastern limb. The notion of quartz mineralisation occupying the axis of a synclinorium is contrary to the situation in the Reefton Goldfield where quartz mineralisation is affiliated with folds associated with an anticlinorium. Historic mine data reveals that below No.4 Level the quartz-gold mineralisation, in the Alpine Mine, occupied a steeply dipping ore channel. The strike of the channel was to the northwest and within this structure the are shoots plunged to the north at approximately 40¦. Archival mine plans show that two quartz bodies, the North and South Blocks, were present at No. 4 Level. Although the North Block was followed down to No 14 Level (530 m vertically below the surface outcrop) the South Block was only mined as far as No 7 Level. Sampling on No 7 Level together with the results of trial mining suggest that the grade of quartz underfoot in South Block is low. Information from the Mines Statements and mapping undertaken by the Gold Prospecting Scheme reveals that faulting had a profound influence on the intregity and extent of the Alpine Reef. The reef occupies a Inajor shear zone but little is known about it. It is also apparent that below No 7 Level the reef was progressively shattered by faulting and this may be the chief reason for the decrease in grade in the lower levels of the mine. No substantive facts are available about wall rock alteration effects adjacent to the Alpine Reef Still this is not surprising considering that comments on the mineralised pug envelope and breccias adjacent to the mined quartz shoots at the Globe - Progress Prospect were omitted from contemporary publications. In spite of this the existance of sulphide bearing reef casing lithologies cannot be completely dismissed since 9.15 m of 'reef track' has been reported in Reids No 2 Level.

Jan 1, 1996

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By P. E. Cavanagh

THE Ontario Research Foundation has developed a family of dry magnetic concentrators which, when used in conjunction with a dry grinding mill such as an Aero-fall mill, will allow the production of a completely dry magnetite concentrate. Previous experience with extrusion of iron ore and with pelletizing of fine iron concentrates suggested that it might be possible to develop a method particularly suited to the agglomeration of completely dry concentrates which might have some practical advantages over other methods of agglomeration. Pelletizing is the preferred method of agglomerating very fine iron ore concentrates. Magnetite concentrate is fod to the pelletizing equipment in the form of a moist filter cake. Binders and plasticizers may be added if necessary, and the moisture content must be increased or adjusted to the percentage necessary to give good balling action and satisfactory green strength in the resulting moist pellets. The moist ore with a closely controlled water content of about 7 to 12 per cent moisture may be rolled into pellets by a snow-balling action in a pelletizing drum, a Lurgi pan, or a Mac-Dowell disc pelletizer. The resulting green pellets are fired by one of several alternative processes to produce a hard pellet which has sufficient strength to withstand handling and shipping.

Jan 1, 1957

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By Alla D. Mah

Relatively pure aluminum nitride (AIN) recently has been prepared in sufficiently large amounts to permit a variety of experimental studies.4/ Several mechanical and chemical properties have been investigated, which show that this substance has good potentialities as a container for liquid aluminum, gallium, and boric oxide. The present work by the Bureau of Mines was undertaken to obtain thermo-dynamic data pertinent to the calculations regarding thermal stability and reactivity of aluminum nitride. The following measurements were made: (1) determination of the heat of formation from the elements at 298.15° K.; (2) determinations of the heat capacity over the temperature range 51° to 298.15° K. and the evaluation of the entropy at 298.15° K. therefrom; and (3) determinations of the heat content over the temperature range 298.15° to 1,800° K. These data are combined to obtain free energies of formation from the elements between 298.15° and 2,000° K.

Jan 1, 1961

By P. Cienfuegos, J. Loredo, J. J. Fernández, F. Pendás

This coal basin is a fore-deep basin with a lot of similarities with the Appalachian basin in the U.S.A., where throughout the 1990s, the research in coalbed methane grew rapidly due to a combination of factors, including the high prices for gas and electricity. In the Asturian Central Coal Basin 129 coal beds with thickness ranging from 0.8 to 1.5 m have been recognised in the productive carboniferous in an area bigger than 1500 km2. The maturation grade of these coals varies from the external zones of the basin where the volatile content ranges from 35%-40% to 20%-30%, to the internal zones of the basin where the volatile content ranges from 20% to 10%. In this context a sustainable exploration for fossil fuel is currently being undertaken in the most favourable areas of the basin in order to evaluate the real possibilities for coalbed methane (CBM) resources.

Jan 1, 2005

By Mateus Sotelo Menezes

Uma ferramenta de trefilação deve suportar as altas tensões a que fica submetida durante o processo sem apresentar deformações. Para isso, o projeto da fieira deve iniciar com a escolha correta do material de fabricação e um dimensionamento adequado. Tais fatores podem minimizar a ocorrência de falhas, tanto na fieira, quanto no produto trefilado, assim como diminuir as tensões e desgaste na ferramenta. Portanto, este estudo visa analisar as regiões de uma ferramenta de trefilação industrial que estão sujeitas as maiores amplitudes de tensões ao longo de um processo de trefilação. O método de elementos finitos foi utilizado para simular a trefilação de uma barra de aço utilizando uma ferramenta de carbeto de tungstênio. O perfil da fieira foi inserido no software e então analisado em diferentes etapas ao longo do processo de trefilação e após o seu término. Observou-se a ocorrência de tensões compressivas superiores a 600 MPa na região de trabalho e as maiores tensões trativas foram visualizadas na região de saída, com valores próximos a 200 MPa. A presença de tensões residuais não foi registrada na fieira, como esperado.

Aug 17, 2017

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By Marco V. Ginatta

Current world production, 60'000 ton/y, is exceedingly too small for titanium's extraordinary combination of favorable properties; it should be 1,000,000 ton/y (7% of stainless-steel). Prices that competitively sustain that sales volume are achievable only with electrolytic production, as it is for all other commercial nonferrous metals. But titanium does not have its commercial electrolytic plants yet, because of producers decisions and strategies, scientists works, industrial problems with chloride process, lack of consumers sponsors. Fluoride high temperature process has the advantages of aluminum electrolysis, plus other favorable characteristics specific to titanium and its feed material. One electrolytic titanium potroom replaces several different plants used for sponge production. Production of titanium ingots with zero defect is achieved. The solidified cathode rectangular slabs are suitable for direct rolling.

Jan 1, 2001

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966