Search Documents

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By D. Racicot, T. Hanel, E. H. Chown

Over thirty plutons in the Chibougamau-Desmaraisville belt were examined briefly in the field and sampled, in addition to the few masses that have been studied in detail. The survey indicates that the intrusions may be conveniently grouped in four main categories, based on their time of intrusion. These are; remobilized basement domes, pre-kinematic intrusions, syn-kinematic intrusions and postkinematic intrusions. Basement domes, as exemplified by the Lappa rent Massif, are composed of migmatized tonalite-diorite gneiss that has undergone at least two periods of mafic dyke intrusion and at least three major deformational periods. The rise of the basement domes was accompanied by extensive mylonitization and the intrusion of syn-tectonic plutons. Pre-kinematic plutons, such the Chibougamau pluton, are diori te-tonalite in composition, and were intruded into the supracrustal pile and partly eroded before the main deformation of the belt. Syn-kinematic plutons occur principally as marginal intrusions bordering the belt (Barlow), or as discrete intrusions along structural highs (La Dauversiere), and are either hornblende monzodiorite or tonalite in composition. Post-kinematic plutons, such as Muscocho, are principally granodiorite and often porphyritic intrusions locally deforming the enclosing rocks. The close relationship between mineralization and high-level intrusions such as the pre-kinematic and some of the post-kinematic plutons is discussed.

Jan 1, 1984

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By R Hall

Subduction zone magmatism is a direct response to tectonic and chemical processes operating at convergent margins. Changes in the tectonic configuration of plate boundaries in SE Asia during the Cenozoic had consequences for the nature and volume of magma produced. Retreat or advance of the trench hinge has probably been an important process in controlling the presence or absence of magmatism in SE Asian subduction zones. This process also provides a means of replenishing the mantle wedge and counteracting the effects of melt extraction in depleting the wedge. Changes in the nature of recycled material and lithologies of the over-riding plate also have the potential to influence the lavas that are erupted in arcs. Several locations in SE Asia have experienced magmatism bearing the geochemical signature of subduction but are remote from coeval subduction zones. Such magmatism requires an earlier period of mantle enrichment by subduction but may result from localised extension. The distribution of such magmatism may provide information of tectonic value. Some adakitic magmatism occurred in tectonic settings where there is no evidence for subduction of young oceanic crust at the time of magma genesis. Slab melting in such settings is not possible and alternative mechanisms are required to explain the occurrence of, at least some, adakitic lavas.

Jan 1, 1999

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By S. Gallagher, A. Mayton

Introduction The mining industry has long been associated with a high incidence of low back disorders and pain (Klein et al. 1984, Leigh and Sheetz 1989, Brinckmann et al. 1998). It is believed that the higher incidence of these injuries among miners is the result of high exposures to postural demands, heavy manual work, and exposure to whole-body vibration (WBV). Recent work has indicated that miners involved with heavy lifting (especially in restricted spaces or on uneven ground) or who have been exposed to whole-body vibration in undamped seats experience noticeable changes in their spines that are consistent with degeneration of the intervetebral discs of the spine (Brinckmann et al. 1998). As will be described shortly, there is mounting evidence that disc degeneration plays a large role in the development of low back pain, particularly chronic back pain. Until fairly recently, medical doctors generally assumed that back pain was the result of muscle strain, ligament pain, or so-called “trigger points” (Bogduk, 1997). However, research supporting these mechanisms of pain has been very scant. When subjected to scientific scrutiny, none of these mechanisms has been shown to relate to back pain in a convincing manner. On the other hand, there are three mechanisms that have been shown to be highly associated with back pain in controlled scientific studies: sacroiliac pain (present in 13% of back pain sufferers) (Maigne et al. 1996), facet joint pain (present in 15 % of back pain sufferers) (Schwarzer et al 1994), and disc disruption and degeneration (present in 39% of chronic back pain sufferers) (Moneta et al. 1994). The latter mechanism, which bears the highest relationship to back pain that has been objectively demonstrated, will be the focus of this section. Scientists now believe they have a good idea how back pain may develop in cases involving disc disruption and degeneration (Bogduk 1997). As the spine experiences loading during lifting tasks or whole body vibration, the first structure to fail is called the vertebral endplate, which is a structure that attaches the disc of the spine to the vertebral body (Figure 1). The endplate typically experiences a fracture, which the body will attempt to heal by means of scar tissue. Unfortunately, this scar tissue impedes the flow of nutrition to the disc itself (discs are dependent on nutrition from the vertebral bones), and if the supply is reduced sufficiently, the disc will start to degenerate. As this degeneration process proceeds, fissures or tears in the fibers of the disc start to develop. If any of these tears is a grade 3 fissure (Figure 2), an inflammatory response occurs in the disc, which will lead to the well-known sensation of low back pain (Peng 2006).

Jan 1, 2007

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

By QIE Jun-mao, DONG Fang, DENG Hao-hua

The DIL402C thermal dilatometer and STA449C thermal analyzer were employed to test the linear expansion and contraction coefficient，CP and DSC curve of 304 stainless steel. The result showed that the linear expansion coefficient range was 20.9700×10-6～21.5712×10-6 and the linear contraction coefficient range was 21.2528×10-6～21.9471×10-6.The linear expansion and contraction coefficient were higher than other steel grade，so the 304 stainless steel belonged to the crack sensitive steel. Because of the crystal phase transformation occurred during the 1000~1400 ℃,the curve of CP fluctuated obviously and the defects of casting blank occurred easily. Chosen 1414℃ as the liquidus temperature of 304 stainless steel based on the analysis results of DSC. The curve of DSC was unsmooth during 1450～1100℃，the crystal phase transformation occurs and thermal stability of slab was inferior.When the initial solidified shell formed in this temperature range,the thickness of the shell would be nonuniform and the surface defects occurred more easily.

Jan 1, 2015

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By D J. Brake

There has been a strong trend over the past decade in hard rock mines towards the use of very high powered auxiliary (or secondary) fans; in many mines, the installed power for the secondary ventilation system now exceeds that of the primary ventilation system. This also reflects the trend to use two-stage auxiliary fans pushing air into a single ‘trunk’ duct that in turn splits into multiple branches with multiple outlets feeding multiple workplaces. This often produces a poor result in terms of face flows due to the high resistance, high leakage and badly managed duct outlets, as well as high fan capital and operating (power) costs, which in turn also results in a higher cost for the underground power reticulation/distribution systems. This paper explores the reasons why this trend exists and what ventilation practitioners can do to utilise less expensive systems that simultaneously deliver better workplace conditions. It includes a case study.CITATION:Brake, D J, 2017. Auxiliary ventilation design – why and how mines waste so much power on inferior systems, in Proceedings Australian Mine Vent Conference 2017, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By Christoph Pichler

A special desulphurization slag accrues during the processing of iron ore to steel, which is needed to generate high quality steel. Sulphur removing is done by different technologies, but the most common one is the generation of a high sulphur containing slag by sulphur affine elements. Currently, this desulphurization slag is partly recycled, however, huge amounts are still dumped. To utilize this desulphurization slag for future purposes, a recycling process must be established. Therefore, first characterization of this material started some years ago at the Chair of Nonferrous Metallurgy, Montanuniversität Leoben. Subsequent trials in lab scale size were performed, also some investigations for different treatment steps were evaluated, starting with a parameter study in a hot stage microscope at various gas-atmospheres. Finally, the developed recycling process concept was verified in pilot scale trials to confirm the new recycling technology. Due to the successful treatment process, also a patent was applied.

"What is your history and how did you get involved in mining?Like many SME members, I came from a mining community with a family history in mining, in my case Walkerville, MT. Both of my grandfathers were underground miners. My father was a miner for a short time. He later sold drinks to the miners. Unfathomable by today’s standards, my dad would pick up the miners’ checks at the pay office and have them cashed and waiting with a shot and beer for the miners when their shift ended. My mother was a nurse, who from time to time, would patch up an unfortunate miner. I remember walking past multiple picket lines on the way to and from grade school, watching homes being boarded-up. I grew up with a deep respect for the critical relationship between labor and management.I had no intention of going into mining and initially set out to pursue a career in chemical engineering. But I attended my first two years of engineering at Montana Tech, due to the proximity and affordability. This is where I met Dr. Tom Finch, a mining professor who taught statics to the engineering students. After a coaching session in a hallway, half way through my sophomore year, I switched to mineral processing engineering. In his colorful way, Professor Finch advised me that, “You do not want to make #@*!! erasers and #@*!! Jell-O the rest of your life go talk to the guys in mineral processing.” He was very persuasive and here I am today.How about your involvement with SME?I encountered SME out of school and a little later in my career. Terry Maio and Jim Arnold invited me to local section meetings in the Missouri Lead Belt. That was my first exposure to the technical programming and relationship building that was possible at the local level. After Ozark Lead shut down and I relocated to Nevada, Rich Johnson, Scott Barr and Dave Collins encouraged me to attend my first annual meeting in Salt Lake City, UT. I joined SME at that time and was fortunate to be engaged by members like Art Schweizer and Jim Arnold, and I soon began the leadership progression for the Mineral & Metallurgical Processing Division. Since then, I have supported SME at the national and the local level serving in multiple roles and capacities."

Mar 1, 2017

By J. M. Lottering

Paper written on project work carried out in partial fulfilment of B Eng (Chem) degree Operational factors influencing the electrostatic separation of mineral sands were investigated in a laboratory separator. Measurements were collected online by means of an optical sensor using diffused reflectance spectroscopy to determine the mineralogical composition. The results have shown that the roll speed and potential were the dominant operating variables, collectively explaining more than 83% and 68% of the product grade and yield, respectively. In contrast, the feed rate, temperature and position of the plate did not affect separation. The effect of the ambient relative humidity, ranging from 10% to 45%, could not be assessed conclusively and at best appeared to have a weakly beneficial effect on the product grade. Keywords: process modelling, high tension roll separator, mineral sands

Jan 1, 2006

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015