Search Documents

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By Gordon B. French

In order to better understand the relation- ship of underground and surface oil shale processing systems, a block flow chart is presented in Fig. I. From this figure only modified in-situ and Room and Pillar underground mining are currently committed and into the Detailed Design and Construction phases. Figure II illustrates the times required (Federal land site) to bring oil shale operation into production. As this example shows, only those companies having progressed beyond the exploration stage have a chance to obtain oil shale production within the next 10 years. A more detailed breakdown of the oil shale development for those on private lands or having already obtained Federal lease lands is shown in Fig. III for shale oil development (without major regulatory changes).

Jan 1, 1981

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By John D. Morton, J. H. LaVerne Palmer, Douglas J. Belshaw

An extensive programme of ground instrumentation and observation was carried out for the West Duff in Outfall Sewer tunnel project prior to and during construction, to establish the performance characteristics of the rock through which the tunnel and appurtenant openings were dug and to examine the nature of the lining-to-ground interaction. The existence of high horizontal residual ground stresses was confirmed, and values established by overcoring. Rock deformations and stress changes were monitored during tunnelling. Permanent stress and strain monitoring devices were set into the final lining and these are continuing to operate. INTRODUCTION The site is located on the north shore of Lake Ontario at Pickering, some 20 miles (32 kilometres) east of Toronto, Canada where a variable thickness of glacial or interglacial sediments overlies bituminous shale bedrock of. the Collingwood Formation which is lower Ordovician age. Approximately 50 feet (15 metres) of glacial cover exists at the shaft, though this thins abruptly at the regressing cliffed shoreline such that several small areas of exposed bedrock exist in the lakebed. The general location, overall geological section and detailed site plan and profile are illustrated in Figs.1,2 and 3 respectively. General properties of the rock as established during an extensive test drilling and site investigation programme are listed in Table 1, while stress determination by USER overcoring stress meter device are given in Table ll. These data formed the basis of analyses which were done to examine the intended outfall design, and to detail the construction procedure and the observational instrumentation programme.

Jan 1, 1979

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By Steve Kral

A few months ago, Congress passed, and President Bush signed, a national energy bill. Designed to decrease the nation’s dependence on foreign sources of energy, the bill earmarked several billion dollars to increase the use of U.S. coal reserves. The bill also modified permitting regulations to speed up development of the coal reserves located on federal land. Coal currently supplies more than half of the nation’s electricity needs. And as housing starts continue to in-crease and with the nation’s appetite for electronic gadgetry, the demand for energy in the United States will only go up. That means coal producers must expand production while at the same time containing costs so they can enjoy this period of improved coal prices.

Jan 1, 2005

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months' operation.

Jan 1, 1979

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By Bradford F. Townsend, Colin R. Speers

INTRODUCTION This is the first in a series of papers addressing practical tunnel lining design. The format for this and future papers is to present a particular topic and support the presentation of the guidelines by the practical application of a case history. The primary intent is to provide guidelines for the geotechnical and structural design of tunnels where the tunnel size and/or ground conditions dictates that systematic support of the excavation is required following each increment of excavation. This method of tunneling is commonly referred to as Sequential Excavation and Support(SES) and is also commonly termed the New Austrian Tunneling Method (NATM) The authors developed the design guidelines from experience gained over the past two decades during the design and construction of several major railway, highway and water-transfer tunnel projects in Africa and Asia. During this time it has been possible to compare the performance of the as-constructed structures to the predicted performance as given by the design process. Excavation was typically carried out in widely varying ground conditions (weak-bedded rock, jointed hard rock, and soil-like poorly cemented rock with groundwater). It is therefore intended that the design guidelines could be applied, in general terms at least, to any tunnel excavated in any ground mass condition with any ground material type (hard rock, soft rock, bedded rock, soft ground, and soil) with or without ground water. This first paper is an introductory paper that defines the scope and a brief outline of the design issues that may be presented in detail in later papers. What is design? It may be thought of as any rational/verifiable/justifiable process whereby a concept is transformed into information that can be used to bring the concept to reality. In the case of a civil structure, design may be defined as that process, which is documented and can be audited, that determines information such as the shape (form) of the structure, the dimensions (size) of the structure, the thickness and strength of structural members that comprise the structure, etc. This information can be used to compute the time, money and resources required for

Jan 1, 2005

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By Robert C. Horton

The Getchell Mine is located on the east flank of the Osgood Mountain Range in the Potosi Mining District, Humboldt County, NV. Mining in the area first began in 1883 for copper, lead and silver in skarn-related deposits. Tungsten was discovered in the skarns in 1916 and was mined sporadically until 1957. The first major discovery was made in 1933 when two Winnemucca prospectors, Edward Knight and Emmett Chase, found gold at the present site of the Getchell gold mine. In 1934, after a small amount of preliminary prospecting, the claims were purchased by Noble H. Getchell of Midas, NV. The Getchell Mine Inc. was organized and exploration and development work began on a broad scale. Major funding was provided by George Wingfield and investors he assembled. Laxalt described Wingfield’s immediate history prior to his financing of Getchell as follows.

Jan 1, 1999

By C. J. Newman

Before 1995, the smelting process at the Kennecott Utah Copper Corp. (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. When considering expansion, it was decided that the existing process would not lend itself to a program geared toward processing the total output of copper precipitate and copper concentrate from KUCC mining and concentrating operations. During 1989 and 1990, several smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1 Mt/a (1.1 million stpy) of copper concentrate, with the ability to expand to 1.2 Mt/a (1.3 million stpy). The smelter facility that used the Noranda technology was shut down in May 1995. The flash smelting furnace operation began in June with the flash converting furnace start-up a few weeks later.

Jan 1, 1999

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. William Langer, U.S. Geological Survey, is the chair of the SME industrial minerals technical committees and the vice chair of the technical committee for construction materials. Other technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •Ismail Yildirim, Imerys, fillers and pigments. •Charles Landis, BPM Minerals, sorbents, filters and process aids. •Ray Harris, Wyoming Geological Survey, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them

Jan 1, 2004

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025