Search Documents

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 1927 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein.

Jan 1, 1935

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

Four taconite plants were studied to establish the extent of hazard to plant personnel which exists based on long-term exposure to noise. The criteria for evaluation include the 90 dBA and 85 dBA summations of partial exposures. Data from extensive interviews were used to determine all work stations or locations which employees occupied and how much time they spent in ach location in a typical working day. Noise level measurements at every designated location were then made. By means of a computer program, these time and noise level data were us d to find the optimum noise reductions which would be required throughout each plant to meet both noise criteria. Subsequently, each plant was examined in detail so that the apparent sources of noise for each of the locations requiring noise reduction could be delineated. In tabular form, this report presents the hazardous locations for each plant, the existing noise level, the optimum noise reduction which would be required to meet the current and proposed laws, and the sources of noise which produce the existing noise level.

Jan 1, 1977

By M. C. Furerstenau

Adsorption behavior of various surfactants on sulfide minerals is very much affected by the nature of the surface of the mineral. Since sulfides are naturally meta-stable, oxidation occurs when they are exposed to air, especially in aqueous environments. As a result. oxygen assumes a major role in sulfide flotation. Mechanisms of adsorption of various thiol collectors on sulfide minerals have been reviewed. The electrochemical behavior of various sulfide minerals has also been reviewed. Flotation behavior of galena, chalcocite, sphalerite, pyrite, chalcopyrite and pentlandite has been presented together with the. flotation of copper sulfide- nickel sulfide ore.

Jan 1, 1993

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By Yiling Zhang, Paul A. Salvador, Gregory S. Rohrer

"Photocatalysis utilizes solar energy to produce hydrogen by splitting H2O. When a thin film of photocatalyst TiO2 is supported on a ferroelectric BiFeO3 substrate (band gap ~2.5 eV), the TiO2/BiFeO3 heterostructure is capable of photochemically reducing Ag+ to Ag0 in aqueous solutions under blue light with enhanced efficiency. The observation of spatially selective silver patterns on surface of the heterostructure after reaction suggests that photogenerated electrons and holes in ferroelectric BiFeO3 are driven in opposite directions to reduce their chance of recombination. Comparisons of the amounts of reduced silver on TiO2 film grains with distinct phases/orientations show that the reactivity is mildly preferential on anatase TiO2 phase and does not strongly depend on crystallographic orientation of BiFeO3.IntroductionTitania (TiO2) is capable of photocatalytically converting H2O to hydrogen and oxygen under the irradiation of ultraviolet light. [1, 2] One of the limiting factors for titania to be used as an effective photocatalyst is its band gap. Because the absorption edges of rutile and anatase titania are at 3.0 eV and 3.2 eV, respectively, they can only absorb light in the UV portion of the spectrum, which is about 3% of the available solar energy. [3-5] This limitation has motivated attempts to modify the absorption edge of titania so that it can absorb visible light.One strategy is to substitute a portion of the titanium and/or the oxygen with other atoms. There are numerous reports on visible light absorption of titania by doping and co-doping of Cr, V, Mo, Sb, Fe, N, S, C, and F. [6-34] Another strategy is to add an adsorbed molecular species that absorb visible light and donate an electron or hole to the titania, such as organic dyes [33, 35, 36] and Ce3+/Ce4+. [37, 38]The strategy in the present work takes the approach of depositing a pure titania thin film on a visible light absorbing substrate BiFeO3 to induce visible light activity of the heterostructure. BiFeO3 is a semiconductor with a band gap of about 2.5 eV [39-41] and is photocatalytically active in visible light. [42, 43] It is also ferroelectric with spontaneous polarization along pseudo-cubic <111> directions of 6.1 µC cm-2. [44] The spontaneous polarization gives rise to internal electric fields that drive photogenerated charge carriers, namely electrons and holes, in opposite directions to reduce their chance of recombination. [45-47] Additionally, the separation of electrons and holes leads to the spatial separation of reduction and oxidation half reactions so that the back reaction of intermediates is also suppressed. Such charge carrier separation has been reported in TiO2/BaTiO3 heterostructures with UV light illumination. [48-51] The TiO2/BiFeO3 heterostructures in this work combine both advantages of the relatively narrow band gap and the internal fields in BiFeO3 to enhance the overall photocatalytic activity."

Jan 1, 2014

A recently developed technique for use in collieries is described in which samples of gas of relatively high vitiation value are obtained from points deep within a developing goaf by means of pipes. This technique prevents dilution of small quantities of carbon monoxide by large quantities of fresh ventilation air and eliminates interference from shotfiring gases. By using the technique it should be possible to assign a characteristic ratio of carbon monoxide to oxygen consumed to any district and to predict the onset of heatings.INTRODUCTIONGas analysis has played a vital role in detecting heatings in collieries all over the world. By analysing return air from a district and by calculating the percentage ratio of volume of carbon monoxide found to oxygen consumed (known simply as the &quot;carbon monoxide ratio&quot;) it has been found possible, in many cases, to assign a characteristic ratio to a district under consideration. This characteristic ratio serves as an index of the spontan~ous combustion tendency of a goaf area. Any definite and consistent increase in the ratioabove the normal figure&#183; indicates that a heating is developing and hence adequate preparations may be made to deal with the trouble.This ratio technique was developed by Graham (1920-21) who found (Table 1) that the temperature of oxidizing coal was directly related to the ratio obtained from analyses of the effluent gas.Until recently, most attempts to employ a similar technique in collieries working the Greta Seam (N.S.W.) were not successful. From experience gained over the past few...

Jan 1, 1961

By Yiming Sun

The 5-mile long Bay Tunnel is a major water supply facility to be constructed under the San Francisco Bay and adjacent marshlands between the San Andreas Fault to the west and the Hayward Fault to the east. The tunnel will have a two-pass lining system consisting of a watertight precast concrete segmental initial lining and a welded steel pipe final lining. Considering the Bay Tunnel?s location between two major active faults, the design earthquake produces a significant peak ground acceleration estimated at approximately 0.6g. To develop a design that can achieve the seismic performance objectives, full dynamic seismic analyses were performed using site-specific earthquake time histories. The analyses considered soil-structure interaction and an evaluation of the transverse and longitudinal effects of the design earthquake. This paper describes the seismic analyses and the design measures recommended to minimize potential adverse effects of the design earthquake on the tunnel final lining.

Jan 1, 2008

In-pit crushing and conveying (IPCC) is being increasingly considered as an alternative to traditional truck-shovel mining methods. The move towards IPCC is driven by a number of factors including the potential to reduce greenhouse gas emissions, the availability of skilled labour and the need to increase extraction rates to levels that present significant challenges to traditional methods.When considering the relative performance of IPCC and truck-shovel methods, the outcome can be inadvertently impacted by either the use of different simulation approaches, or techniques that do not adequately model the processes in sufficient detail.A simulation approach is proposed that models both IPCC and truck-shovel using the same software platform and is capable of functioning at a wide range of resolutions from life-of-mine scale through to second-by-second asset tracking level. The simulation framework also holds models of processing equipment and hence the mining simulations can be extended to gauge the impact on downstream plant.The approach, known as mine-process operational simulation (MPOS), can be tailored to the level of information available and hence the type of study required, ie order of magnitude, prefeasibility, feasibility, or detailed design.Using information from block models and a range of detailed equipment and process models, MPOS can span major system discontinuities, typified by the mine-plant interface, to allow the estimation of final mine and plant product specifications.

Dec 6, 2010

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels&apos;, i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal (&apos;balancing&apos;) source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By I. J. Lin

The effect of various types of structural modification on the critical micelle concentrations (CMC) and hydrophile lipophile balances (HLB) of certain surfactants has been considered. Using the concept of effective chain length for the substituted species, an index of hydrophobicity (I) has been defined. It is hoped that such an index will allow one to choose surfactants for particular purposes in a less arbitrary fashion than heretofore.

Jan 1, 1973

An information system (I/S) plan is a means for establishing and communicating the direction the organization intends to take to provide the information required for achievement of organizational goals and objectives. The rapid advancements in information technology, the increasing complexity of systems, and the growing dependence of mining companies on these information systems have emphasized the need for more comprehensive I/S planning. This subsection explores this need, the role I/S planning can play within a mining company, and finally describes a methodology for development of an I/S plan.

Jan 1, 1979

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By Met B. E

The increasing pace of modern mining makes constantly greater demands upon the several contributing departments of rock breaking and transport, and rock-drilling, as the spearhead of attack, has received a great deal of attention with respect to both machines and steels. By a series of mechanical improvements, combined with the application of selected heat-treated alloy steels, the rock-drill has now been developed into a machine capable of rapid drilling and long service under severe working conditions. As a factoryproduct made under strict metallurgical control it is as foolproof as, say, the modern automobile, and, like its prototype, it can be kept in efficient operation by a minor amount of attention during use and by periodical adjustments and replacements.The same cannot be said, unfortunately, of the drills with which the machine is supplied; in conventional mine-shop practice these are made of the best tool steel shaped and heat-treated under the poorest of metallurgical conditions.The crudities of steel-shop practice have, in fact, always prevented the full exploitation of the steels available at any time, and even at the present day the general standard of treatment offers a contrast with the quality of the steels which moves the metallurgist to amusement, despondency or outrage, according to his temperament. Nevertheless, the tendency persists to meet the increasing demands of the rock-drill primarily by the use of still better steels, and secondarily by improvement, of the steel-shop practice. Athird type of development is the introduction of factorymade tools in the form of detachable bits and rods. It is proposed in this paper to deal with these three aspects of the recent developments in rock-drilling.*Re-written from a lecturette given during the First Ordinary Meeting, 1936.

Jan 1, 1936

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By R. R. Brown

The solubility and the activity of aluminum chloride hexahydrate, A1C13?6H2O, in aqueous solutions were determined as a part of the Bureau of Mines, U.S. Department of the Interior, research to improve mineral processing technology for recovering alumina from low-grade domestic resources. The solubility of A1C13 in pure water was found to be 31.09 and 31.77 wt-pct at 25° and 85° C, respectively, and decreased drastically to 10 and 0.1 wt-pct when the respective amounts of 20.3 and 37 wt-pct hydrochloric acid (HCI) were added in solution. The equilibrium constant for the solubility of hexahydrate, activities, and activity coefficients of A1C13 and H2O were calculated and compared with the results from the available methods of estimation. The results were shown to be useful in leaching nonbauxitic ores for extraction of alumina by changing the solubilities of component salts upon addition of HC1. Simultaneous solubilities of A1C13, FeC13, KC1, and NaC1 in solutions of HC1-H2O were also determined and their effects on the purity of A1C13?6H20 crystallized from mixed salt solutions are briefly discussed.

Jan 1, 1979