Search Documents

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

By A. Stawsky

Effective use of diesel vehicles in underground mining requires attention to improved control of diesel exhaust pollutants such as particulate (soot), oxides of nitrogen and sulfur and carbon monoxide. An experimental survey Is made of diesel emission aftertreatment control techniques including water scrubbers, catalytic converters, exhaust gas recirculation (EGR) and soot filters. Use of two or more techniques in combinations are tested for optimum control of all exhaust pollutants. Dynamometer data is developed for steady state and computer controlled simulated mines duty cycles operation of Deutz F6L-714 and F8L-413 engines. Exhaust Quality indices (EQIs) are calculated from dynamometer data for comparisons among the control combinations examined. The Corning diesel particulate filter (DPF) is shown to be the most promising and practical device. The Corning DPF in combination with EGR provided the best (lowest) EQI from the test data. Use of the DPF requires additional regeneration mechanisms such as a catalytic filter coating or fuel additives. A metal mine field test is made of DPFs on an operational scoop tram to test practical applicability. Further development is proposed for application to various mine conditions and for improvement of DPF regeneration techniques including coating with newly available catalysts.

Jan 1, 1987

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By N. S. Dalal, B. Jafari, F. H. Y. Green, V. Vallyathan

"INTRODUCTIONThe mechanistic details of the biological events leading to coal workers pneumoconiosis (CWP) are not yet fully understood, despite several decades of extensive epidemiologic1.2 and laboratory studies.2-6 Epidemiologic studies1.2 have shown, for example, that the incidence and severity of CWP differ markedly in the different regions and mines at comparable exposures, but laboratory investigations2-6 have demonstrated only partial correlation of the epidemiologic data with the differences in the mineral composition and the rank of coal mined. In particular, while epidemiologic data indicate1.2 direct correlation of the· prevalence and severity of CWP with the rank (i.e., % carbon content) of coal, this correlation has not been established by laboratory4'6 and animal exposure3 studies. In order to explain these results, in 1980 Artemov and Reznik' suggested that perhaps they arise from the fundamental differences in the surface properties of the coal. dusts inhaled by the coal miners and those used in the laboratory studies: while the miners inhale freshly fractured coal particles, henceforth called the 'fresh' coal dust, the laboratory studies generally utilize 'aged' coal dusts (i.e., dusts that have been stored for many days or even longer). Reznik and Artemov' used electron spin resonance (ESR) spectroscopy to show that the mechanical crushing of some Soviet Union coals generated organic free radicals and that the concentration and the decay times (hence the reactivity) of these radicals were higher for the coals of higher ranks. Since some of the radicals decayed within a few minutes in air, the authors surmised that while these radical species could lead to certain specific pathogenic reactions at the sites of mining operations, this might not be the case in the laboratory studies, due to the conventional use of 'stored' dusts which would be expected to contain significantly smaller free radical concentrations. This is consistent with the recent findings that, standardized, aged coal dusts exhibit minimal cytotoxicity. 8While the above mentioned work of Artemov and Reznik7 did suggest a possible new clue to the pathogenesis of CWP (i.e., the role of the coal based free radical species), no direct biological/cytotoxicity data were provided to show that 'fresh' coal dusts were, indeed, more pathogenic than the 'stale' ones. Because of the rather significant implications of the Artcmov-Reznik hypothesis to the understanding of 1hc biochemical mechanism and, hence, the strategies for the eventual containment of CWP, we have initiated a comparative study of the free radical formation and cytotoxicity properties of freshly crushed coal ·particles. As done by Artemov and Reznik, 7 we have used the ESR technique as the direct method of measuring the concentration and decay kinetics of the coal based free radicals. Our preliminary ESR studies on two Pennsylvania coals, a bituminous (carbon content 72 % ) and an anthracite (95 % carbon) coal, have confirmed the Artemov-Reznik finding that the crushing-induced free radical sites are higher on the coals with higher carbon content (i.e., higher rank).9-11 In the present work we describe our more recent results of a parallel study of the time dependence of the decrease in the free radical content of a freshly made anthracite dust (as measured via ESR) and that of the dust's cytotoxicity potential as measured by the extent of hemolysis of (sheep) erythrocytes. We have also investigated the effects of free radical scavengers on the cytotoxicity potential of the dust and deduce that indeed the free radicals could play a significant role in the initial events in the mechanism of the cytotoxic effects due to the inhalation of coal dust inhalation."

Jan 1, 1990

By John Nagy, Hylton R. Brown, Irving Hartman

"INTRODUCTION The tests described in this publication were planned to provide information on the explosibility of metal-powder dust clouds. This subject has become increasingly important because of the large quantity and variety of metallic powders now used for military and industrial purposes. To provide the increased amounts of metallic powders needed in the manufacture of munitions and to supply the demand created by the rapid growth of powder metallurgy, existing metal-powder plants have been enlarged, production schedules accelerated, and new plants erected. In some cases new methods of producing metal powders have been developed. This increased production and the development of new manufacturing methods have caused an increase in the number of metal-powder fires and explosions, with accompanying heavy loss of life and property. These have emphasized the need for information on methods of providing protection against hazards inherent in the production and handling of powdered metals. This paper gives results of laboratory inflammability and explosibility tests made to April 1, 1943, and is a progress report. Many descriptive details have been omitted purposely; they will supplied in a later publication, expected to be a Bureau of Mines bulletin."

Oct 1, 1943

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much information was collected on the salt resources and industry of the United States. The more important features of the information thus gathered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geological Survey,a which will supplement this report, relating to salt-making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Washington, D. C.

Jan 1, 1917

By O. M. Schaus

This paper is one of a series, prepared by the Bureau of Mines and deals with the Montreal mine, one of only two active properties in Wisconsin on the Penokee-Gogebic range. The purpose of this paper is to describe the conditions of occurrence of iron ore in a particular property and to present sufficient details of equipment and production methods to convey to the unacquainted operator a correct idea of the mining practice.

Jan 1, 1930

By James W. Martin

This user's manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

By P. Nicholls

Patent records show that the idea that the burning of fuels can be improved by mixing or pretreating them with chemicals 6 dates back to the early years of the last century. By 1845, English and French patents included the specific beneficiations of elimination or reduction of smoke, soot, and clinker; reduction of the ashes, presumably meaning the total weight of refuse from the ashpit; elimination of sulphur fumes; increase in the rate of burning; increase in the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 pounds or more per ton of fuel, but after 1860 the quantity was rarely more than 4 pounds. There is no record of the extent to which these patents were commercialized, but after 1884 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many companies marketed proprietary products that were sold under the general name of "fuel savers." Since its establishment in 1910, the Bureau of Mines has continually received inquiries about these products and, at the request of other govern-mental departments, has tested some used in accordance with the instructions of the purveyors; the results were all negative and, within the accuracy of measurements, the products had no effect on the burning.

Jan 1, 1937

By O. C. Ralston

The Bureau of Mines has under development on a technical scale an electrolytic process for treating oxidized ores of zinc , using caustic soda as an electrolyte . Whereas the Bureau process can alternately make either solid zinc or zinc dust , the following paper , from the Ludwigshafen research laboratory of the well -known I. G. Farbenindustrie , A. G. , of Germany, deals only with production of zinc dust from sodium zincate solutions and may well serve as introduction to the subject for American metallurgists . The Bureau of Mines pioneered in the idea ; a study on laboratory scale by H. J. Morgan and 0. C. Ralston was made early in the First World War, and published in Transactions of the American Electrochemical Society . The Eckardt paper , translation of which follows , goes more thoroughly into the preparation of electrolytic zinc dust , and later publications of the Bureau of Mines will deal with broader details and application of the idea to treatment of lowgrade ores and metallurgical intermediates , which is the point where Eckardt left off . 4 The Eckardt report became available through operations of Field Information Agency , Technical ( FIAT ) of the Office of Military Government for Germany (US ) , which made bibliofilm copies of the files of internal technical reports of many of the German industrial establishments , Eckardt's report is dated April 1939 and was taken on FIAT Microfilm Reel MM 106 , frames 82-101 , which is on file as Publication Board Document 41411 in Office of Technical Services of the U. S. Department of Commerce , Washington , D, C , Eckardt points out that the normal source of zinc dust is the blue powder of the zinc retorts , which decreases in volume every year owing to technologic improvements in zinc smelting. I. G. saw the importance of making a

May 1, 1948

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By Lorraine B. Burgin

This study by the Bureau of Mines documents the leadtime required for preliminary and detailed exploration, development of the mine, and construction of beneficiation and support facilities for selected copper deposits in Arizona. The time for major exploration ranged from 1 to 15 years, time for open pit development (or construction) was 1 to 4 years, and time for under- ground development was 4 to 8 years; one underground mine presently being developed may require 12 years to achieve production. Construction of the beneficiation plants required 8 months to just over 2 years. The data are supported by historical facts for each deposit during the leadtime stages from location of claims through exploration, construction, expansion, and leaching. The sequence of development and factors contributing to differences in the time spans are discussed. Histories are detailed for the Miami, Castle Dome, Copper Cities, San Manuel-Kalamazoo, and Twin Buttes properties; briefly summarized are the Pinto Valley, Miami East, Esperanza-Sierrita, Pima, and Mineral Park Properties. Each mining operation had its own pattern of development, and together they present a source of planning information for the development of other properties.

Jan 1, 1976

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By Alla D. Mah

Compilation of data on materials of metallurgical interest is one of the important activities of the Berkeley Thermodynamics Laboratory of the Bureau of Mines. Recent renewed interest in metallurgy of vanadium renders the present compilation a timely guide for experimentation to improve present methods or to develop better methods of extractive metallurgy. Thermodynamic data for vanadium and its inorganic compounds have been critically surveyed, selected, and compiled into one convenient reference from which information can be readily obtained for evaluating heat balances, determining trends, and establishing limits of metallurgical processes. By indicating the direction of experimentation, this report enables the saving of time, effort, and expense which would otherwise be necessary for trial and error experimentation. Much of the data has been obtained experimentally at the Berkeley laboratory. Other data were collected through an extensive survey of worldwide literature through April 1965. Estimates were made when no data were avail-able. Data on the vanadium halides was sparse, and the results derived from existing data were at times divergent. Some of the selected values for the halides may need modification as more or better experimental data become available.

Jan 1, 1966

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966