Search Documents

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By Lee Browne

The transformation of Peru’s Tintaya copper project from a state-owned company to a private company is under way and the results have been successful. Since Magma Copper Co. assumed operating management in December 1994, production and costs have improved dramatically. To understand the transformation of Tintaya, the transformation of Magma Copper must also be understood.

Jan 1, 1996

By J. K. Borchardt

The use of statistical design to optimize deinking process design has been studied for the flotation deinking of newspapers. The interactions of two variables are often important in determining flotation deinking efficiency. The interactions can be synergistic or antagonistic. These interactions would not be discovered using the traditional method of varying one parameter and holding the other variables constant. An experiment design in which two or more process parameters are varied simultaneously is required to identify these interactions. A considerable number of conclusions could be drawn about the relative importance of process variables on ink particle size distribution, ink removal efficiency, and flotation yield loss in a flotation deinking process. However, these findings could be influenced by the deinking surfactant and the ink chemistry.

Jan 1, 2001

When overburden depth exceeds economical recovery in openpit coal mines, the use of highwall mining systems has increasingly come into play. However, stability in the highwalls is always a major safety concern during such mining. The U.S. Mine Safety and Health Administration requires that highwall mining operators follow ground control plans that specify the pillar sizes necessary to prevent collapse that would threaten highwall stability.

Jan 1, 2006

By C Ferron, R Massimi

There is approximately 240 000 tonnes of arsenic trioxide dust stored in underground chambers at the Giant Mine in Yellowknife, Northwest Territories, Canada. To minimise the amount of arsenic released to the environment, a number of closure alternatives are being considered. One alternative is to mine the dust, encapsulate it and dispose the mixture into a secured landfill. The potential leaching behaviour of the encapsulated dust was examined in a laboratory programme. Cylinders of arsenic trioxide dust mixed with cement/aggregate and bitumen were prepared. The dust content varied between zero per cent and 60 per cent of dry weight charge. The cement cylinders were tested for strength, leaching and freeze/thaw durability. The bitumen cylinders were tested for leaching only. The results show that increasing dust content in the cement cylinders negatively impacts the strength and the freeze/thaw durability of the samples. A contributing factor is likely the high water to cement ratio in the samples. Leaching tests show that arsenic release from cement cylinders increase with increasing dust content. Arsenic concentrations in leachates do reach a plateau at a certain point in time. Arsenic release from bitumen cylinders was significantly lower compared to cement cylinders. Arsenic concentrations eventually were less than 0.05 mg/L in samples containing up to 25 per cent arsenic trioxide dust. Arsenic leaching rates were found to decrease by an order of magnitude over the course of three months.

Jan 1, 2003

1. Domestic Production and Use: In 1980, 13 companies operated 33 primary aluminum reduction plants, with 3 firms accounting for 62% of production. Washington, Oregon, and Montana accounted for 30% of the total production; Texas, Louisiana, and Arkansas 19%; Tennessee, Alabama, and North Carolina 15%; other central and eastern States 36%. Based on published producer prices output of primary metal in 1980 was valued at over $7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 26% of domestic consumption in 1980, building 22%, transportation 21%, electrical 12%, consumer durables 7%, and other uses 12%.

Jan 1, 1981

By Wern-ping (Nick) Chen

In concrete lined tunnels, formwork removal timing may be controversial. Contractors seek to strip the form as soon as possible, and designers seek to keep the formwork in place as long as practical to protect the fresh concrete. Formwork removal timing is normally specified as a function to its insitu concrete strength. This approach may work for smaller diameter tunnels, but fallacy occurs when applying this approach to larger diameter tunnels, since a larger diameter would experience more displacement than a smaller diameter tunnel from its own weight. Excessive deformation may fail a tunnel to meet its roundness criterion and overstress the lining causing cracking or falling from the crown. This paper presents a contractual mechanism to mitigate this issue.

Jan 1, 2008

By E. P. Youngman

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative, to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of British Guiana has been prepared from the best available sources in Washington and is, released subject to amplification and correction, if necessary, by United States foreign-service officials. INTRODUCTION The sources of information available in the preparation of this paper are the following: 1. The Crown lands ordinance, No. 32 of 1903, September 26, 1903.

Jan 1, 1934

By Chen Jianping, Wu Li, Wei Banyun, Chen Canchang

Liquified petroleum gas mixed with oxygen has been used as a new type of mixed gas source for gas detonating system. The experimental studies have been done on the detonation feature of gas detonating transmission in a long and thin tube, the transmitting reliability for detonating network, the design on gas exploder and test devices. The results of the study show that (1 )Liquified petroleum mixed with oxygen can be used as a new type of regular gas source. (2)The transmission of detonating wave is reliable for new type of mixed gas in a 500-meter long plastic tube with 3mm inner diameter and the detonating velocity is up to 2500m/s. The detonating wave can surely initiate and transmit several branched gas detonating cap and explosive through the end of detonating network, the tubes inner diameter for the detonating quenching is 0. I’mm. (3)The gas exploder designed by authors can be used for gas propotional distribution,strong turbulence-mixing,initiating by reflex shock wave and safety control purposes. The developed double flowmeter can be used together or seperately in responsible for main testing in the system.

Jan 1, 1999

By Jérôme Boutin, Rémy Oddo, Sylvain Ouellette, Paul-Émile Boileau, Gilles LeBlanc, Pierre Marcotte

ackleg rock drills are widely used in the mining industry and are known to generate high levels of hand-arm vibration which contribute to the development of the hand-arm vibration syndrome for exposed miners.1-3 To reduce the vibration levels, a prototype of an antivibration handle was developed as part of a previous study.4 To provide some bench marking for this handle prototype and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. As the current ISO 8662 series of standards could not apply directly to this type of tool, there was a need to design and validate a test bench to evaluate the vibration emission values of jackleg drills, while taking into account the conditions specific to the operation of this type of tool. Methods A test bench including an energy absorber, was developed for testing jackleg drills based on the ISO 8662-3 standard 5. The energy absorber was bolted to a 3300 kg concrete block to ensure tool stability. A pictorial view of the device is given in Figure 1. For validation purposes, acceleration measurements at the handle of a conventional jackleg drill were taken simultaneously along the three axes (xh, yh and zh) in an underground rock drilling operation as well as on the test bench. The handle accelerations were measured for three different jackleg angles (13º, 28º and 43º) determined with respect to the floor. Moreover, each measurement was repeated at least three times to asses the data repeatability. [ ] Results As a preliminary validation of the test bench, Figure 2 provides a comparison of the frequency weighted rms acceleration spectrum measured along the zh-axis, for both underground drilling and operation on the test bench (28º jackleg angle in both cases). It is shown that the vibration measured on the handle of a jackleg drill operating on the test bench is representative of that recorded during typical rock drilling operations, despite the fact that some harmonics of the percussion frequencies are generated with a higher amplitude on the test bench. Table 1 provides

Jan 6, 2006

Lime and cement manufacturing has a proud history in Otago, with the earliest lime kilns appearing around 1849 at Caversham and Kaikorai in Dunedin . At Dunback or Makareao (to be precise) three well-type kilns were built by the government in 1899. In 1909 these kilns were leased to the then Milburn Lime and Cement Company. They erected a large brick Schmatolla kiln in 1909, elliptical in plan and fired by coal gas. The kiln operated up until 1944 before being left derelict. The quarry which supplied the kiln also supplied the Burnside Cement works from 1929 up until its closure in 1988. The quarry was shifted to the top of the hill in the 1950s.

Jan 1, 1992

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By Alfred Weiss

At the end of the first decade of digital computing in the minerals industry, geostatistics in North America was still in its infancy. This was in contrast with the rest of the world where the technique of kriging was already widely practiced. By the end of the 1970s, there was increasing awareness among practitioners of its potential. But it was not until the late 1980s that geostatistics was universally applied and accepted. This was due, in large measure, to contributors at Applications of Computers and Operations Research in the Minerals Industry (APCOM) symposia. Such an evolution in new computer methods could again be observed at APCOM 26.

Jan 1, 1996

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By Donald O. Capstick

The local geology, the lack of recorded mining activity, and our field investigation and associated sampling indicate a low potential for mineral resources. Claim records and the literature review failed to show any lode or heavy mineral placer mining claim locations that are definitely in the area or anomalous mineral concentrations in the study area. Field investigations revealed no claims, prospects, or mineralized areas.

Jan 1, 1982

By Jeff Reid, Mohamed Maghari, Nicholas Joens

The Burnaby Mountain Tunnel was an integral part of the Trans Mountain Expansion Project. General Contractor, Kiewit Ledcor TMEP Partnership (KLTP), contracted with McNally Construction to build an underground tunnel between the Burnaby and Westridge Marine terminals under Burnaby Mountain. The pipeline was constructed within a 2.6-kilometre tunnel, eliminating the need to run the pipeline over the mountain and minimizing community impacts. The complexities of this Project led to multiple innovations, including the design of a Tunnel Boring Machine (TBM) capable of excavating through mixed-faced conditions concurrently thus allowing the Project team to complete the tunnel with limited geotechnical information.

Jun 23, 2024

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973