Search Documents

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

By J Brisebois

The derelict Lake George Mine is located at Captains Flat in NSW, acommunity of approximately 450, which lies some 43 km southeast ofQueanbeyan. It straddles the Molonglo River, which flows toQueanbeyan and thence the nationÆs capital, Canberra. Catastrophictailings dam failures in 1939 and again in 1943 resulted in the transportand dispersion of thousands of tonnes of sulfidic wastes downstream,with terminal settling in Lake Burley Griffin, in Canberra. The mine wasclosed in 1962, and major rehabilitation in 1996 - 1997 addressed the riskof further collapses, and reduced water flow into the underground mine.Nevertheless, acid mine drainage from the mine, and seepages ofcontaminated water from the capped tailings dumps continue to pollutethe Molonglo River for some 30 km downstream.Environmentally, the highest contributor to the total contaminant loadof the river is the Main Adit Spring. This was shown to be a constantgroundwater-driven acidic flow, with contaminant generation resultingalmost entirely from the ingress of gaseous oxygen into the undergroundworkings. Long term remediation may be possible at source, by pumpingreducing gases into the sealed mine, but the probability of thistechnology succeeding to the required degree is yet to be demonstrated. For at least the medium term, treatment of contaminated water flow(s)will be required to achieve any of the water quality targets that may beapplicable to the river. Three methodologies were short listed, but anumber of strategic uncertainties remain, which the NSW Derelict MinesProgram will address. Future risk arising from long-term contaminantrelease by the treatment wastes must be considered. Appropriate data,and realistic long-term performance parameters regarding the relativestabilities of water treatment sludges are scarce, and make properevaluation of competing technologies problematic.

Jan 1, 2003

By Fabjanczyk M. W

A limitation to present theoretical roof reinforcement design methods is the inability to derive accurate and quantitative information about the roof rock condition and the action of reinforcement at various excavation stages. To obtain the information required to assess roof rock stability, detailed monitoring of the in-situ behaviour of reinforcement and roof strata is required. Reliable instru- mentation and techniques have been developed for use in underground coal mines to identify the geometry and magnitude of displacements occurring in roof rock and the forces generated in reinforcement. The use of such instrumentation allows an accurate assessment of the in-situ capability of reinforcement and the mode of reinforcing action developed. In-situ monitoring can supply data required for the practical design of reinforce- ment and assess the potential stability of current designs. The use of such data together with mine wide appraisal of rock and stressfield considerations, can allow roof reinforcement to be designed on the basis of a predicted roof Response.

Jan 1, 1986

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

In sizing of wet coal by the horizontal vibrating screen, screen openings to be used is much restricted, because coal is sticky and its bulk density is little. The electrically heated screen and other various types of screen had been tried to screen raw coal and coal as raw materials at a few mm. However, they failed to realize satisfactory results. On the other hand, fine sizing of coal is requested by many fields. For example, raw coal is desired to be screened at the fine rate, before being fed to the coal preparation control system in order to transport undersizes as unprepared coal particles and to reduce load in coal preparation waste water treatment system.1) Coals fed to the fluidized bed boiler also should be sized at a few mm. Regardless of many requests on fine sizing of coal, it seems that there are many cases to omit the basic screening process, because the screening is very difficult on a industrial scale. Size control as pretreatment of coal as raw materials is presented as one of the basic screening processes. In 1979, Kinki Industrial Co., Ltd. and Nippon Steel Corporation jointly succeeded in developing the vertical centrifugal screen. Closed -circuit crushing system by the use of this screen has operated actually at N.S.C, Hirbhata .Works, and realized the anticipated result. Consequently, this system has established the position as the most basic technology in the coal preparation. 2), 3), 4) This system has been also introduced to Nakayama Steel Works, Ltd. in 1982. This system termed the CPC (Coal Preparation Control) Process has been operated smoothly in both N.S.C. and Nakayama. Reported herein is the practical application of the vertical centrifugal screen termed V3-Separator. (V3 means vertical, versatile and vibration.)

Jan 1, 1984

By Morrison R. D

This paper describes major events in the design, construction, camtissioning and operation of the Elura concentrator. It covers the period fran September, 1974 when laboratory testwork on drill core cotmenced to March, 1983 when the concentrator catmenced operation on run of mine ore following successful completion of initial ccnmissioning tests. The concentrator was designed to treat 1.1 million tonnes of lead-zinc-silver ore per year with a plant availability of 89 per cent. This treatment rate has been achieved for test periods.

Jan 1, 1983

During induration of iron ore pellets produced from magnetite concentrates, there are many reactions occurring simultaneously. While the magnetite is being oxidised to hematite, carbonate fluxes are being calcined, leading to the formation of complex oxides. Calcination of fluxes and the formation of calcium and magnesium ferrites and silicates during the preheat stage can influence the magnetite oxidation process. As the calcination reaction proceeds quicker than oxidation at temperatures experienced during the preheat stage (700 - 1200¦C), the bulk flow of CO2 emanating from within the pellet should disrupt the diffusion of O2 to the magnetite reaction as the gas fluxes are similar in magnitude. This increases the time required for the oxidation of the pellet. Using an infrared rapid heating furnace, experiments were performed on heating individual magnetite green balls in an air atmosphere. These experiments showed that time played an important role in the extent of oxidation and calcination and temperature significantly influenced the initial evolution of high temperature phases such as magnesioferrite, calcium ferrites and calcium silicates. Understanding the kinetics of all these reactions for a particular pellet feed, and their interaction, is important for optimising the design of the induration furnace.

Jan 1, 2005

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

Upon subduction, water is liberated from the sediments and the porous struc- ture of the oceanic crust and from de- hydration of minerals for redistribution and chemical reaction. A survey of pro- cesses which are likely to occur along the subducting plate reveals that water may well be basic in subduction induced gas generation, magma formation and ore deposition. In analogy to the industrial water gas process, reaction of water with car- bonaceous matter, in subducted sediments is likely to yield substantial volumes of hydrogen and carbon dioxide. While water and carbon dioxide appear to play a determining role in the development of differentiated magmas, hydrogen will react with metal sulfides and sulfur to form hydrogen sulfide which is essential in sulfide ore depo- sition. A survey of possible metal extrac- tion chemistry along subduction suggests a stepwise solubilization of metals from sediments and oceanic crust, and a poten tial accumulation of dissolved metals in zones of characteristic composition. The metal spectrum in ore deposits at near surface appears to reflect the com- position of the solution in the respec- tive subduction zone. A tendency for preferential solubi- lization of copper at subductidn level, from among the transition metals, an in- creasing generation of hydrogen sulfide in the sane direction and partition effects as well as sulfide precipitation characteristics lead to enrichment in copper and to its selective deposition in the direction towards the trench as observed in S. Latin America. A postscript deals with the formation of native copper.

Jan 1, 1986

By Trois P

A fully instrumented and bench-mounted diamond drilling machine, purpose designed and built, has been used for investigating the effect of aqueous solutions of various chemical compounds when used as drilling fluids. The rocks investigated were andesite, basalt and granite, the chemical compounds were alkylamines, with various hydrocarbon chain lengths, aluminium chloride and dioxane. Rotation speed seems to be one of the major factors affecting the emergence of mechanochemical effects as the results obtained with aluminium chloride clearly indicate. Penetration rate is either unaf- fected or enhanced by the presence of certain compounds, such as aluminium chloride. On the other hand, penetration rate diminishes when the drilling fluid contains dioxane and exhibits an apparently unpredictable behaviour with alkylamine solutions, although it appears that an increase in hydrocarbon chain length usually equates to an increase in penetration 1. Full Professor, Mining and Mineral Dressing Department University of Cagliari - Italy 2. Associate Professor, Mining and Mineral Ikea- sing Department University of Cagliari û Italy rate. Rock texture seems to have a pronounced effect on test repeatability. With hexadecy- lamine acetate solutions in concentrations ranging from 10-5 to 5 .10-4 molò dm 3 and 41.88 radòs-1 rotation speed, 46 % increments in penetration rate of andesite were observed, with respect to water, whereas penetration rate decreased in basalt by as much as 60¦%o when a dioxane solution was used as drilling fluid. An interpretation of the observed effects is proposed in the light of current knowledge of solid state physics and physical Chemistry.

Jan 1, 1992

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

By Ofori-Ansah K

The zeta potential on the surface of activated orit carbon were estimated in lhe presence of selected cations and anions that are normally associated with gold bearing ores in Kalgoorlie area of Western Australia. Additions of such ions to solution of varying pH shifted the isoelectric point of carbon from pH 4.45 to pH 7-8.3, while the anions moved Lhc isoelectric point 10 less than pH 3.2. In the presence of gold cyanide SoluLion additions of spectator ions indicated the isoelecLric poilll to be aL pH less than 3.2; the only exception was for Fe" ion where the isoelecLric point was at pH 5.9. The decrease in zeta potential appeared to be related to the counter-ions present. The decrease may also be related to the adsorption of hydroxyl ion complexes that are likely to be formed when cations are present in the solutions.Gold adsorpLion by activated orit carbon from gold cyanide solution seem to be indicated by the magnitude of zeta potential on the carbon surface. An attempt is made to relate gold adsorption and zeta potential on carbon surface with the pH of the medium.

Jan 1, 1984

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

By Penttila V

The Paleoproterozoic Hitura Ni-Cu deposit in western Finland is in an ultramafic igneous complex composed of two subvertical plug-shaped bodies embedded in intensely migmatised felsic gneisses. The ultramafic complex is not far from a north-south trending graphitic and sulphidic gneiss zone interpreted to be a primary sulphide-graphite unit in the metasedimentary sequence. The sulphide accumulation exists as a zone parallel to the contact of the northern ultramafic body. The ultramafic rock types, now mainly serpentinites, have primarily been olivine adcumulates in the core grading to olivine orthocumulates and pyroxenites towards the margins. Coarse-grained felsic pegmatite veins injected serpentinite where they now exhibit prominent zoned alteration rims of chlorite, antophyllite and talc. The serpentinite core of the body was primarily an olivine adcumulate derived from a tholeiitic or high-Mg basalt parental magma with about 11 wt % MgO. Metamorphism and alteration have totally changed the igneous mineral compositions and the rock types are serpentinites (from olivine adcumulates), ambhibole-bearing serpentinites and amphibole-chlorite rocks (from pyroxenites). As the result of CO2 alteration talc is an accessory mineral throughout the serpentinite. Like silicates, also sulphide minerals are altered. In the core of the body the low-grade sulphide dissemination still reveals primary igneous interstitial forms. The core sulphides are now mackinawite, pentlandite and valleriite instead of primary igneous pyrrhotite and pentlandite derived from Mss. At the marginal zone the heavy dissemination and net-textured sulphides display pyrrhotite-pentlandite-magnetite intergrowths with magnetite films along cleavage of sulphides, mackinawite in pentlandite and exsolution textures of different low-temperature pyrrhotite phases as the result of alteration processes. Mechanically weak rocks, complicated structures and textures of the ore, magnetite and mackinawite intergrowths in pentlandite and readily-floating MgO silicates cause problems in exploitation of the deposit. Solution to problems come from selective stoping, three-step classification in grinding, froth-washing technique and on-line process control based on ore type determination from process data using an expert System

Jan 1, 1996

The estimate of an ore reserve is a vital statement made about a mineral occurrence by an evaluator. It is important that such a statement communicate reality to all groups involved in a mining project, be they technical, financial, company directors, Stock Exchanges or the public. Ore reserve statements should state both resources and recoverable ore reserves. Resources may be important in very long term considerations, (because mining, metallurgical technology and economics change with time) but recoverable reserves are todays reality. The important factors contributing to recoverable reserves (in a general sense) are geology, mining method (and its impact on dilution and ore loss), metallurgical recovery, costs and commodity prices. These all need to be reflected in the ore reserve statement. In this paper recoverable ore reserve concepts across a wide range of orebodies are considered and discussed with respect to geology, mining method and ore reserve calculation procedures.

Jan 1, 1987

By J A Evans

A well-maintained and low cost mining operation today requires the use of condition monitoring techniques. At ERA - Ranger Mine oil analysis, vibration monitoring, infra-red themtography, and performance analysis have been successfully applied over the last four years to lower operating and maintenance costs. All condition monitoring is scheduled through a comprehensive in-house developed maintenance management system known as the Engineering Information System (EIS). (EIS) is used extensively at Ranger to ensure consistent frequency and recording .of all condition monitoring data. This paper provides an insight into the benefits of condition monitoring and explores the future direction for condition monitoring techniques at Ranger.

Jan 1, 1994

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

Level measurement of underground orepasses is important. Orepasses are not only utilised to funnel ore to the shaft skip loading station but also as silos for storing of ore in order to smooth out ore flow in a shaft system. Safety and operational efficiency are also improved as proper orepass level measurement could prevent overfilling of tipping areas. A study was therefore commenced to determine alternative technologies available as well as identifying practical installations across the Anglo American plc Group. From an instrumentation perspective an orepass system is an extremely difficult environment to take measurements in. Factors like dust, vapour, interference, bridging, wear and physical installation have to be taken into account. The study discusses time-of-flight (ultrasonics, radar and laser) measurement techniques followed by other possible solutions. These solutions included strain gauge measurement, the æjumping monkeyÆ technique, radiotomography, fibre optics and very long baseline interferometry (VLBI). Finally, various South African suppliers have been approached in order to determine instrumentation that is available for orepass level measurement in the marketplace. These recommendations were verified, where possible, by visiting the claimed installations.

Jan 1, 2005

By Roe P, Lowell A

This paper outlines software development and design work carried out by Mincom Pty Ltd in collaboration with Capricorn Coal Management (CAPCOAL) for computer based design of rehabilitated strip mine landforms at German Creek Mine. Current developments and future application areas for this software are also discussed in relation to other mines in Central Queensland. The development program was initiated in response to statutory requirements placed on mining companies in 1990 to produce a five year Plan of Operations which was to include a contour plan of the final rehabilitated mine landform at the end of the five year planning period. This plan was to be submitted to the Department of Resource Industries (DRI) by 1 December 1990. Due to the limited time given to prepare the plan, a work program was formulated in collaboration with Mincom Pty Ltd to develop suitable software to carry out the design work and provide the required plans and quantities. The software had to include computer based methods to allow design of the proposed landform in line with the rehabilitation strategy adopted by CAPCOAL at the time.

Jan 1, 1991

By J Shillabeer

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998