Search Documents

By R. K. Kandasami

"Naturally occurring geomaterials such as sandstone, limestone and other soft rocks, residual soils are composed of a particulates held together through a cohesive matrix, usually composed of argillaceous or siliceous cementing agents. Geo-materials such as these have been reconstituted in the laboratory using ordinary Portland cement in lieu of the naturally occurring cohesive matrix, in addition to using sand particulates. This cohesive frictional granular ensemble is an ideal model material for understanding the mechanical behaviour of transitional geomaterials such as soft rocks. An important consequence of this cohesion that pervades the inter particulate system is the enhanced tensile strength when compared to a purely granular ensemble. The assessment of strength of these soft rocks and cemented sands is often understood in the framework of continuum mechanics, i.e. considering the cemented sand to be a continuum, and performing simple elemental tests such as uniaxial compression or tension tests. A simple model to describe the behaviour of these cemented sands has been to use elements such as springs, sliders, and dashpots in parallel to describe the existence of a cohesive and frictional component of strength (Jiang et al. 2007). In the framework of continuum mechanics, the mechanical response of these cemented sands have been modeled using traditional plasticity theory, for example utilizing variants of the traditional Mohr Coulomb model, Modified cam clay (Sun and Matsuoka 1999) etc. The typical sand models are amended to include the effects of cohesion, as proposed by Lagoia and Nova (1995).The mechanical response of cemented sands is understood to be transitional to the behaviour of a typical particulate assemblage and a quasi-brittle material. However, the effect of length scale in these material systems has not been investigated. This paper presents a series of uniaxial compression experiments conducted on weakly cemented sand specimens of various sizes. The effect of length scale in these weakly cemented sands is investigated through unconfined compression tests."

Jan 1, 2015

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

By M. Tadie, J. Wiese, K. Corin

The use of potential control in the flotation of ores has been applied in a variety of operations and presents an opportunity for improvement of selectivity and recovery of valuable minerals. Although it is possible to vary the redox potential (Eh) using chemical additives such as sodium hypochlorite or hydrogen peroxide this is more commonly done by varying the pH and dissolved oxygen (DO) concentration. The present study involves an investigation into the effect of varying dissolved oxygen concentration, ionic strength (IS) and pH on the flotation response with the aim of application to a South African lead-zinc ore. In all cases the Eh is measured as a function of the different DO, IS and pH values. The main objective was to achieve selective flotation of galena from sphalerite. The first part of the work was micro-flotation tests conducted on single minerals with galena used as the basis for effect of the factors studied on redox potential and ultimately recovery. The DO was varied by alternating between the use of air and nitrogen as the gas source to the micro-flotation cell. PH was varied between pH 9.2 and pH 11.8 using sodium hydroxide. In the first part of this study a factorial design approach was used to determine the interactive effects of the variables tested, viz. DO, ionic strength and pH, on the Eh and on the recovery. Redox potential was measured using a combination electrode made up of platinum wire and Ag/AgCl reference combination. Recoveries indicated that pH had the most significant effect on recovery and Eh. The influence of redox potential on recovery was found to be of relevance to the condition of high dissolved oxygen concentration and less so at low dissolved oxygen concentrations. It was also noted that that the combined interaction between ionic strength and dissolved oxygen concentration had a positive effect on recoveries, however this was not so with Eh. The chemistry of the ions in solution was observed to play a dominant role on the recovery due to changes in solubility arising to pH modification. The longer term objective of this work is to determine the optimal Eh conditions for the separation of galena from sphalerite.

Jan 1, 2016

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor's signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

"There are a number of disciplines in the minerals industry for which concern has been expressed regarding the sustainability of human capital. The boom-bust cycles that occur in the industry, the trend in tertiary education towards consolidation or in some cases cessation of minerals related programs and the increasing frequency of fly-in fly-out operations can all contribute towards a decline in the number of professionals with basic skills in process mineralogy. This paper describes approaches taken by the authors to incorporate process mineralogy into three levels of education, namely undergraduate, recent graduate and experienced professionals. The primary objective in designing the learning activities is the development of authentic learning experiences that provide participants with relevant skills in process mineralogy. Selected examples of approaches used by other education groups globally to address this issue are also provided.INTRODUCTIONThe boom and bust cycle of the mining industry has trickle down effects in tertiary education in terms of the ability of universities to consistently provide high quality graduates with relevant skills. When the commodity price surged in 2002 skills shortages in critical resource related professions were reported and despite investment in skill development there was a view from employers that not enough young people were graduating from relevant education programs (PricewaterhouseCoopers, 2012). At the time this signalled positive growth for engineering disciplines catering to the mining industry, however during the downturn cycles, most recently since 2012, graduates exiting from the discipline can find employment difficult and this contributes to reduced enrolments in subsequent years. From an AusIMM (Australasian Institute of Mining and Metallurgy) members’ employment survey conducted in 2013, more than half of the graduates exiting from disciplines related to mining and minerals were not confident of finding employment (AusIMM, 2013). In the long term the concern is not only how to sustain enrolment and graduate numbers but also to provide the opportunity for students to acquire the professional skills that they require to make them attractive to industry.Maintaining and sustaining core competencies in the minerals discipline is an ongoing challenge. There have been a number of recent papers on this issue presented at international conferences (e.g. McCaffrey et al, 2014; Drinkwater and Napier-Munn, 2014) and there is general agreement that one of the ways in which the deficit in foundation concepts can be addressed is through workplace development. Drinkwater and Napier-Munn (2014) presented data from a survey of industry professionals that indicated that more than 90% of respondents undertook on average 30 days of training each year of which approximately 5 days was professional short courses."

Jan 1, 2016

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

By Cy Jordan, Ben Burdett, Adrian Dance, Jack Rainey

"In 1997, EIMCO Minerals installed a knowledge-based control system on one of the five primary grinding lines at Highland Valley Copper. The objective of the system is to maximise throughput without affecting circuit product size or flotation recovery. The system was commissioned in October 1997 on a SAG mill/ball mill circuit following a plant audit and upgrade of the control instrumentation.The system monitors and controls the SAG mill power, bearing pressure and recycle load by manipulating the solids feedrate, water addition and mill speed. The two ball mill and cyclone circuits are controlled through water addition at various points in the circuit as well as the number of operating cyclones.An on-line particle size analyser is used to measure the cyclone overflow quality. Models of the SAG mill charge level and overflow product size are also incorporated. A method of predicting the SAG mill power response to feedrate changes is used to lessen the effect of dead time for improved mill power control. In the future, inferred measurements of SAG feed particle size and hardness will allow changes in ore behaviour to be predicted and compensated for by the system.This paper describes the development of the project -from installation and commissioning to modifications and refinement -along with prospects for the future.BackgroundIn early 1997, EIMCO Minerals was contracted by Highland Valley Copper to install a knowledge-based or expert system control strategy on one of the five grinding lines in the mill. This was to become the start of the Advanced Control Project at Highland Valley Copper (HVC). This paper will review the progress of the Project as well as discuss the prospects for the future.Following a preliminary engineering study (or plant audit) by EIMCO in 1996, it was decided to implement an advanced control system in order to improve plant operations and increase productivity. The study suggested that such a system had a pay-back period of a few months through increased throughput without loss in flotation recovery. Highland Valley already had successfully applied higher level control through their Elsag Bailey distributed control system (DCS) and this was the next stage in process optimisation."

Jan 1, 1998

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By Sandra L. Mesa-Espitia, Gretchen T. Lapidus

Gold present in arsenopyrite matrices is refractory and requires highly oxidative pretreatments in order to obtain acceptable degrees of extraction. However, these release many byproducts that are harmful to the environment. In the present work, a high-grade arsenopyritic ore was pretreated with different solutions, containing hydroxide ion, EDTA, oxalic, tartaric, or citric acids, to improve gold extractions in a posterior leaching step. The pretreatments were carried out at room temperature for 24 hours with a respective ligand concentration of 0.25 M. Once completed, the residue was leached in a thiosulfate solution to quantify the effect of the pretreatment on gold extraction. Only 29% of the gold content was leached, with very slow kinetics, in the untreated mineral. However, after pretreatment with tartaric or citric acid, the kinetics improved, although the percentage of gold extraction only reached 42-45%. The highest gold recovery, with very rapid kinetics, was found with the oxalic acid or the hydroxyl ion pretreatment (70 and 62%), respectively, but also corresponded to the most arsenic co-dissolution.

Jan 1, 2014

By E. Ghali, W. Zhang, C. Su, N. Sorour, G. Houlachi

"Zinc electrowinning process is sensitive to the presence of metallic impurities such as lead ions that could substantially and negatively affect the power consumption and surface morphology. Effect of various concentrations of manganese ions and traces of lead ions up to 2.5 mg L-1 added to the electrolyte during electrowinning have been investigated by electrochemical polarization techniques such as galvanostatic, cyclic voltammetry and potentiodynamic. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were applied to examine the surface morphology and crystallographic orientation, respectively. Microwave plasma-atomic emission spectrometry has been used to determine the lead content in the deposit and in the electrolyte after electrodeposition. It was found that lead ions added to the zinc electrolyte led to the increase of cathodic overpotential and current efficiencies of zinc deposit. However, addition of Mn2+ into the zinc electrolyte resulted in the decrease of cathodic potential and current efficiency of zinc deposit. It can be stated as example that galvanostatic polarisation at 40?C and 52.5 mA cm-2 in presence of lead up to 0.1-0.2 mg L-1 in the electrolyte and 8-12 g L-1 Mn could be better considered as practical working parameters for electrowinning process.INTRODUCTIONApproximately 85% of the global production of zinc metal is produced by electrolytic process (Sinclair, 2005). The main goal of the zinc plant is to obtain pure zinc deposits with high current efficiencies. Smooth and pure deposits with high current efficiency (CE) are always obtained from pure electrolytes (Alfantazi & Dreisinger, 2001). The presence of metallic impurities in the zinc sulphate electrolyte is a major problem for the zinc electrowinning industry, since decreases in current efficiency, changes in deposit morphology and cathodic polarization are observed for electrolytes containing small concentrations of impurities (Ault & Frazer, 1988; Muresan, Maurin, Oniciu & Gaga, 1996). Low level concentrations as parts per million of these impurities are reported to influence negatively the zinc electrodeposition (Beshore, Flori, Schade & O'Keefe, 1987)."

Jan 1, 2016

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

By R. J. Rotzinger, K. W. Major

The Gibraltar Mine and Mill facility were commissioned in 1972 by Gibraltar Mines Ltd utilizing a flowsheet consisting of two stages of crushing followed by a rod mill / ball mill grinding circuit. During operations a number of opportunities were evaluated to expand the mill capacity; however, the economics of the day did not allow any of these projects to proceed. The mine continued to operate until late 1998 when it was shutdown and put on care and maintenance due to low commodity prices. Taseko Mines acquired Gibraltar in 1999 and in 2004, with the improvement in the metal markets, made the decision to restart operations. During the restart planning a number of opportunities for mill improvements and upgrades were identified and, after operations were successfully restarted, the decision was made to once again review expansion opportunities for Gibraltar. Taseko evaluated various expansion alternatives eventually deciding to install a SAG Mill, convert the existing rod mills to ball mills and distribute the SAG discharge to the resultant six 6 parallel ball mills. This paper discusses the design, implementation and commissioning of the SAG mill grinding circuit.

Jan 1, 2012

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016