Search Documents

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By D. G. Brubaker

IN the history of geophysical exploration by the electromagnetic method many procedures and types of equipment have been used. Source arrangements for surveying on the ground have included long wires grounded at both ends, large loops laid on the ground, small horizontal loops, and vertical loops of moderate to small sizes. Receivers have ranged from simple direction-finding coils to combinations of coils and a bridge circuit to measure quantities related to both amplitude and phase of the received signal. Primary considerations in choosing a survey method are effectiveness, speed, and economy. In work on the ground in which locating and out- lining conducting bodies is the objective, methods using a vertical coil and a simple direction-finder have been found the most satisfactory. Mason1 and his associates applied such a method by setting up a vertical source loop, fed with low frequency alternating current by an engine-generator set. With a direction-finding receiver they surveyed lines along the ground in the plane of the loop, taking measurements at each station of the azimuth and inclination of the magnetic field direction. Deviations of this direction from the normal direction, that is, from horizontal and perpendicular to the traverse line, indicated a conducting body. Recent advances in design of light-weight generating equipment have encouraged using this and similar methods.

Jan 7, 1957

By Waldemar Dyrssen

BEFORE discussing the relation between air pre-heaters and waste-heat boilers in conjunction with the open-hearth furnace, it is necessary to have a clear idea about what a preheater can accomplish and what effect it has on the open-hearth furnace, especially from a thermal point of view. It is generally recognized now that the heating of the combustion air in the checker chambers of the open-hearth furnaces is not as efficient as it is-desirable to make it. It is also generally recognized that heating of the air in checker chambers of ordinary construction has its limitations. These limitations are mostly the .space occupied and the cost that would be involved if checker chambers were made larger than according to present practice. There are, however, other. reasons why checker chambers cannot give the highest possible air temperatures. Checker chambers are capable of heating air to very 'high temperatures by using waste gases of extremely high temperatures and, in fact, higher temperatures can be reached with checker chambers than with any other means available. The temperature to which we can heat, air, however, is limited very materially by -the temperature at which the air enters the checkers, be-cause of the fact that checker chambers, as at present constructed, are not efficient in heating air through a wide range of temperatures. In other words, if air in-stead of entering the checker chambers at atmospheric temperatures could enter at about 1000 to 1200 deg. F., the resultant air temperature at the top of the checker chambers would be materially increased. There are now on the market metallic air preheaters which are ex-tremely efficient for preheating air to about 1200 deg. F. Such heaters occupy very little space and can usually be installed at a relatively low cost.

Jan 1, 1928

By Godfrey T. Vivian

Very often important discoveries are made in one industry that may be used to advantage in another, but, owing to the rarity that men step out of one industry into another, these discoveries remain unknown outside of the trade or profession in which they are made. The present paper is written solely with the object of bringing to the notice of mining and metallurgical engineers a centrifugal ore-concentrator which eventually may have a great application. Ore- Grading. Fig. 1 represents the action which takes place when solids of different dimensions are stirred up in a box and allowed to settle as minerals of the same size but of different specific gravity. This principle is applied practically in grading china-clay and in enriching tin-slimes. In the latter case the slimes are stirred around in a tub with water and allowed to settle while at the same time the side of the tub is struck with a hammer. The colloidal slimes are then poured off and various slices taken off horizontally. The great drawback of this process is that the particles are deposited horizontally and all the colloids are lost. Fig. 2 represents the action in which the particles are deposited side by side. Here the drawback is the great length of the box needed in order to prevent excessive loss. The alternative to lengthening the box is to increase the force of gravity. Centrifugal force may be regarded practically as the force of gravity augmented. Fig. 3 illustrates the Gee centrifugal machine for grading ores. The drum, A, fitted with a box, B, is mounted on a shaft or spindle, C, the whole being suspended from a ball-bearing of special design at D, supported between girders, E. Rota-

Jan 1, 1913

Discussion of the paper of H! M. CHANCE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1461 to 1466. R. V. Norris, Wilkes-Barre, Pa.-In his resume of coal-taxation methods Mr. Chance has apparently confined his investigation to bituminous coal, so a summary of the anthracite situation as to coal assessment should be of interest. The anthracite region of Pennsylvania in its 484 square miles of measures lies in the counties of Wayne, Lackawanna, Luzerne, Carbon, Schuylkill, Northumberland, and Dauphin, and in each of these different methods of assessment have been adopted. The assessments for taxation in Pennsylvania are made under Acts of the Legislatures of 1841 and 1842, under which the assessors are re¬quired to "assess rate and value every subject of taxation according to the actual value thereof, and at such rates and prices as the same would bring at a bona fide sale after due notice." Under this general law coal land has been assessed as such, but up to about 25 years ago the coal was assessed at rates so low as to be unimportant, though the rates in each township and municipality, even in the same county, showed no agreement or ascertainable basis. In the late '80s, the need for greater revenue drew attention to the possibilities of collecting much larger taxes from the coal lands and, spurred by public demand, the assessing authorities in some counties undertook a reassessment of coal. The method pursued was to demand from each owner a statement of the area and average remaining thickness of coal on his lands. On this return, made in some cases under oath, an assessment based on foot-acreage was levied, with a resulting great increase in valuation, but the valuation per foot-acre was low and no serious objection was made. This assessment with occasional increases of rate remained in force until 1907, when, in the triennial assessment of that year, a complete revision of the valuation was again attempted, engineers were employed by the counties to check the accuracy of the returns from the owners, and, based on the foot-acreage thus obtained, an enormous increase, to $65 per foot-acre, was made in the valuation. This assessment was resisted in the courts by appeals resulting in very extensive litigation, and a final determination of the validity of the 1907 and all subsequent assessments has not yet been obtained. In the first appeals tried the rate calculated on a foot-acre valuation was reduced by the Luzerne County court to about $45, while the. Lackawanna County courts reduced a larger rate to $67. The county authorities were, how-

Jan 4, 1915

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By W. J. Reagan

All of the material described in the following paper is within the following specifications: carbon, 0.50 to 0.85 per cent; phosphorus and sulfur, 0.04 per cent max.; manganese, 0.60 to 0.85 per cent; silicon, 0.20 to 0.30 per cent. Steels with much lower carbon contents can be handled in exactly the same manner. One of the first things necessary to basic open-hearth slag control is uniformity of charge, particularly as to the silicon content and the percentage of lime charged. Our past work has shown that the silicon content of the charge is more important than the carbon content in determining the carbon at which a heat will melt. We have found that by keeping the silicon content of the charge about 0.60 to 0.65 per cent, and with a lime charge of about 7 per cent (limestone equivalent), our heats melt sufficiently high in carbon to allow a moderate feed of ore and the slag will be of low iron oxide content. In making a heat of 0.75 carbon steel we endeavor to have the heat melt at about 1.20 per cent carbon. The iron oxide content of the finishing slag depends upon the final phosphorus desired; for a given ratio of lime-silica in the slag, the lower the phosphorus desired in the final steel, the higher the iron oxide content of the finishing slag must be. By reducing the lime charge to a minimum, the heats melt faster, and by keeping the silicon content at the desired figure the heats melt with a high SiO2 slag, which has been shown in previous work to give a low iron oxide slag. In most of our work, using a 180,000-lb. charge and with basic pig containing about 1.20 per cent silicon, we use a lime charge of 8500 lb. of limestone and 2000 lb. of burnt lime. The pig charge is about 48 per cent of cold pig, and the charge contains a large percentage of works scrap. This causes a heat to melt with about 1.20 to 1.30 per cent carbon, for a heat that will finish about 0.75 per cent carbon. This gives a heat that will need a feed of about 2000 lb. of ore, and also a slag with an FeO content of about 4 to 5 per cent at melting. The additional FeO obtained from the ore addition will bring the FeO in the slag at tapping to about 6 to 7 per cent. It is necessary to carry quite a fluid slag to prevent pickup of FeO, as a too heavy slag causes FeO to build up in it, giving a finishing slag with a greater FeO than is desired. By adjusting the lime charge of a basic open-hearth heat, a very sensitive adjustment of the slag may be obtained. The figures in Table 1

Jan 1, 1935

By C. V. Millikan

When a flowing oil well is being drilled in with cable tools, it is difficult to determine when an additional streak of pay sand is drilled. By placing a gas meter on the gas-release line from the oil and gas separator, any increase in volume of gas that comes with oil production is recorded. In addition to the better knowledge of sand conditions, these data are a valuable aid in determining the size and depth of shots, plugging off water, and estimating ultimate production. The meter also gives a record of operation while the well is drilling in; and if allowed to remain on the well after completion will give information that may lead to a more efficient recovery of the oil from the sand. A VERTICAL cross section of any oil sand will show great variation in porosity and oil content. In some sands, the entire thickness contains oil, the variation being only the degree of porosity or oil content, but more often the pay streaks are distinctly separated by shells or barren streaks. These pay strata vary in number and may be thin or thick. The total thickness of the sand may be several tens of feet while the part containing oil may be only 1 or 2 ft. thick. The amount of production is not proportional to the thickness of the sand but rather the thickness of the pay streaks. If the total thickness of the sand or the amount that can be drilled is small, or if the initial production is small, the depth at which each stratum of pay is encountered can be determined sufficiently accurately for all present economic purposes. However, when drilling through sand of considerable thickness, giving large initial production, especially where conditions necessitate that the production go through the same gas trap with that from one or more wells already producing, it is difficult to determine the depth at which the pay strata are encountered even accurately enough to guide the placing of shots, and small pay streaks are apt not to be recognized at all.

Jan 9, 1925

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By John M. Lovejoy

I take pleasure in transmitting herewith "Petroleum Development and Technology in 1927," in which we have attempted to set out in a series of 40 papers with attendant discussions the advances made in Production Engineering and Refinery Engineering during the year. The volume also contains a digest of round table discussions on Petroleum Engineering Research problems and Petroleum Engineering Education. In addition to the above we set out in 16 papers a review of production of each producing area of the United States and of the more important foreign countries, together with a review of the world's production and forecasts for 1928. We also include 8 papers on the Economics of the oil industry. The papers and discussions included herein represent the contributions of more than 200 engineers, including the foremost in each line. These papers were presented at technical sessions held in Fort Worth in October, 1927, and at the annual meeting in New York in February, 1928. We desire to express our thanks and appreciation to all those who have contributed to this volume. As in previous years, we have attempted to emphasize the value of both written and impromptu discussions. -We have made a practice of returning all impromptu discussions to the authors for correction and amplification, and because of this practice we feel that the discussions contained herein are in very presentable and readable form. It was decided by the nominat,ing committee when meeting for thc purpose of nominating officers for 1928 to eliminate the vice-chairrnanship for Transportation Engineering, as that branch of the industry seemed to come more naturally under the activities of the American Petroleum Institute. It was also decided by this committee to institute a new vice-chairmanship for Petroleum Engineering Research. Wc have had heretofore round table discussions on engineering research, but through the newly created vice-chairmanship, to which Mr. L. C. Uren was elected, we expect to have more comprehensive sessions on engineering research than heretofort.

Jan 1, 1928

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

By Norman Maxwell

There was more activity in crude production in northwestern Pennsylvania in 1935 than for several years before, resulting in an increased oil production and also in the number of wells completed. Crude -production approximated 16 million barrels for the state, an increase of about one million barrels over 1934. Demand, indicated by refiners' runs to stills, increased proportionally, leaving stocks of available crude at the end of the year at the lowest point since the middle of 1934, when they reached an all-time low. The price of crude varied during the year from a low of $2.02 to a high of $2.27 at the end of the year for Middle district oil. The price of Bradford and southwest Pcnnsylvania oil changed accordingly. The average for the year would be a lower price than in 1934. A summary of the production data for the year 1935 is given in Table 1. In making up this table, 1935 figures were simply added to the table published by S. H. Cathcart last year1. A list of important wildcats is given in Table 2. Bradford Field Approximately 10,000 acres of the proven producing area of the Bradford field is in Cattaraugus County, New York, and it is possible, by differences, to distinguish the Pennsylvania production from the New York portion. The listed production for the Bradford field includes only that portion of the field situated in Pennsylvania, but also includes production from a small pool, locally known as the Mt. Jewett-Kanesholm pool, where the Bradford sand is being developed and flooded in precisply the same manner as that of the Bradford field itself. The Mt. Jewett-Kanesholm pool is not, strictly speaking, an extension of the Bradford field, but inasmuch as it is so closely allied with the Bradford field-—that is, the sand is the same and the production methods are the same—the production and drilling figures include this area.

Jan 1, 1936

A full account of the wonderful Arizona meeting will be published in the December Bulletin. For the strenuous, interesting, and altogether happy week, we express our hearty thanks to those marvels of energy and thoughtfulness, the members of the local committees in Texas, New Mexico and Arizona. In this number we publish the discussion resulting from the technical session on "Flotation." Because of the timeliness of the subject, this session's discussion was transcribed first and sent to the contributors, and, thanks to their promptness in revising, we are able to print it in this issue.

Jan 10, 1916

By A. C. Bluemel, J. S. Harper, J. H. Jett

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of an entirely new high-performance automated transportation system? Advanced transportation systems for the mining industry can be defined as those which lend themselves to automation and meet definite performance and cost objectives. The term automation shall mean that control of transportation system is accomplished by a closed loop electronic circuit which, when started on command, will continue to cycle as programmed until such time as an intelligent feed-back causes the system to shut down.

Jan 1, 1970

By Edward F. Divers

Face ventilation is generally the most critical area in the coal mine ventilation system. Various studies have repeatedly shown that good ventilation is by far the most effective and least costly method of controlling dust and gas problems created during face operations. The Bureau of Mines has recently developed and assisted in the development of several new concepts in face ventilation systems, and in methods to accurately evaluate these systems underground. A new type of scrubber and ventilation system design built into the auger support frame of a continu- ous miner was developed. The objective was to improve face ventilation and reduce respirable dust concentrations. With this arrangement, one scrubber is mounted into each side of the boom. Laboratory and underground tests of various scrubber discharge arrangements showed good to excellent dust and methane control. Combined face ventilation systems, using both blowing and exhaust curtain, potentially offer dust and gas control and deeper cutting. Bureau tests at a mine using a combined face ventilation system and remote- control-operated continuous miners showed excellent dust and methane control. The advancement of line curtain systems beyond permanent supports without exposing workmen to roof fall hazards can be accomplished only with specially designed extendable devices. Numerous concepts for line curtain extension have been developed and tested. For the past several years, the Bureau has been testing various types of extensible face ventilation systems. These extensible systems can generally be classified as floor-, roof-, machine-, and rib-mounted systems. In the past 6 years, approximately 40 systems have been evaluated for feasibility. From these, several have been selected as practical or innovative and are presented herein. A technique developed by the Bureau to accurately and safely evaluate the effectiveness of face ventilation is also presented.

Jan 1, 1982

By Charles H. Snow

In vol. xxxviii. (1889) of the American Journal of Science, under the heading " Pseudomorphs of Native Copper after Azurite from Grant County, New Mexico," Mr. W. S. Yeates describes a most interesting mineral form. His account is, that a material having the appearance of native copper, but brittle and much lighter than native copper (its specific gravity being but 4.15), was submitted to him by the United States National Museum for examination. The substance was reported to him as occurring in masses, varying in weight from one ounce to seventy pounds, and composed of tabular crystals, variously grouped. The specimens, when submitted, ex hibited on the outride a covering of clay; and they were subse quently found to consist of particles of the same clay, intimately mixed with others of native copper, producing the aspect, without the weight, of pure copper. The forms of the azurite crystals, found at Bisbee, Arizona, having been suggested by the specimens, actual goniometer-measurements were made; and the two crystallizations were thus proved to be identical. To these statements I may be permitted to add some further in formation, derived from personal examination, and illustrated with a suite of characteristic specimens collected by myself (Fig. 2).* Grant County, New Mexico, in which these specimens were found, is a region noted for variety of mineral species. The sixth edition of Dana's Mineralogy mentions many of the silver, copper, and lead minerals, and also turquois, aragonite, wulfenite, barite, fluorite, vanadinite, etc. I have noticed also green and red garnet, molybdenite, native alum, smithsonite, bornite, etc., some of which presented peculiar modes of occurrence. The green garnet, for instance, was in masses formed of separate crystals, each of pea-size and not unlike that vegetable in tint and smooth opaqueness. The crystallization was

Jan 1, 1893

By Oliver Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos industry, (2) as to the principal sources of the raw material, and (3) as to the types and modes of occurrence of asbestos. While the modern asbestos industry is comparatively new and its growth during the last decade or two has been marvelous, asbestos has been known and used in a small way for probably 2,000 years-at least since the time of the Roman Empire. Pliny refers to it as "the funeral dress of kings" and Plutarch records its use as lamp wicks. In the middle of the 18th century the deposits of the Ural mountains were opened up and the first factory for the manufacture of asbestos goods was established. But, owing to the limited demand for the goods, the industry disappeared and interest lapsed until about 50 years ago. Since 1860, the asbestos industry has made wonderful strides, and each year sees new uses to which the material can be put, and hence an increased demand and an increased output. Of the three great producers of asbestos, Canada, Russia, and the United States, Canada stands pre-eminent, producing from one-half to three-fourths of the world's supply; Russia comes second, producing ,in 1911 about two and one-half times ,is much as the United States. In 1912 the Canadian production,1 including both asbestos and asbestic, was 131,260 short tons, valued at $2,979,384; while during the same year the production of the United States2 was 4,403 tons, valued at $57,959. Canada holds the first place in the production of raw asbestos, while the United States holds the first place in its manufacture.

Jan 9, 1914

By J. F. Evers, S. Sadiq, F. W. Preston, G. W. Swift

Proper scaling of unsteady-state flow in laboratory gas reservoir models can be achieved if the permeability/fractional porosity ratio is less than 0.5 md. Porous media meeting this specification can be obtained from mixtures of sand and Portland cement provided (1) the water/cement ratio is in the range of 0.35 to 0.40, (2) the sand/cement ratio is in the range of 1/1 to 2/1, (3) the sand grain size is in the range of 48-100 to 18-28 mesh, (4) the mortar curing time is 7 days or more and (5) the cured mortar is dried under vacuum to reduce the temperature level employed during the drying process. The areal homogeneity of the mortars tested is reasonably good, although significant trends in vertical permeability were noted. The Klinkenberg and non-Darcy coefficients of mortar are such that proper scaling of these effects in the laboratory model could be expected. INTRODUCTION A long term deliverability prediction for a gas well is generally based on data determined from flow tests that are of short duration relative to the producing life of the well. These data, together with an estimate of gas reserves in place, form the basis for establishing the parameters of the mathematical model used to predict performance at future times. Results obtained from a mathematical model represent only an interpretation of the physical process being modeled. Experimental verification of the production process from discovery to abandonment is needed where production occurs under carefully controlled conditions. Ideally, one might consider such an experiment to be conducted in the field. Even if the cost of such an experiment could be justified, the time required would make it impractical to consider. However, if the time scaling problem could be handled properly, an experimental model of the gas reservoir production process could provide the necessary data to study the mechanisms of the production process in a reasonable time period. An experimental model has been designed and constructed using the data of this study as a basis. The model reservoir system consists of one producing well located at the center of a right-circular cylinder of porous material. Ten to 15 observation wells are located at strategic offset positions from the producing well. These wells, and the producing well, are fitted with pressure transducers so that the pressure-time history can be recorded at various radial and azimuthal positions in the drainage area during the entire production life of the system. Time is scaled in the model so that the time required to produce gas from discovery pressure to abandonment pressure is about 2 hours. This compares with a 20-year producing life in the model's field counterpart and gives a time scale factor of approximately 1:100,000. DESIGN CRITERIA To establish design criteria for the experimental model, the reservoir is considered to be a finite right-circular cylinder of radius rr, and height h with a producing well of radius rw located at the center and completed through the producing formation. This reservoir consists of a porous medium which has a uniform permeability k and gas porosity and the gas contained in the reservoir has density p, viscosity µ and molecular weight M. Initially, the pressure at all points within the reservoir is uniform at po. and the reservoir temperature is T. Since the reservoir production process has been demonstrated to occur in two distinct transient modes for either Darcy or non-Darcy flow,l it is

By W. Scott Dunbar

INTRODUCTION Methods of linking boundary integral (BI) solutions with finite element (FE) solutions have been well described theoretically in other publications (e.g., Zienkiewicz, et al., 1977). The purpose of this paper is to point out some practical aspects of implementing these linkage algorithms for rock mechanics applications and to describe an alternative linkage algorithm. A not so obvious motivation for using FE-BI linkages is illustrated in Figure 1. The cost of modeling the excavation of the crusher station by the BI method can equal or exceed the cost of an equivalent FE model. This is due to the large surface area which must be modeled by the BI method. In such cases, a more economical approach might be to model the region immediately adjacent to the crusher station by finite elements and link the solution at the periphery of the FE model with a solution for the exterior region. Further economies can be realized if some flexibility in the type of exterior solution is possible. For example, it would be desirable to use a coarse discretization of the FE-BI interface for a BI solution, which would be less demanding of computer storage and time, or to use an analytical solution for the exterior region. The alternative linkage algorithm to be discussed allows such flexibility. BOUNDARY INTEGRAL METHODS There are basically two formulations of BI methods: the direct and the indirect. FE-BI linkage algorithms depend on which formulation is used. The purpose of this section is to briefly describe each method.

Jan 1, 1982