Search Documents

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

By Palmer W. T

The successful re-opening of the Cobar min- eral field was dependent upon the success- ful introduction of highly productive, low cost mining. Mechanised cut and fill stop- ing with incline access was selected for the C.S.A. mine because it permitted flexi- bility, complete primary extraction with no secondary pillar recovery, minimised dilu- tion and oxidation, a minimum of pre-pro- duction development and because diesel powered load-haul-dump (L.H.D.) units were proving reliable and highly productive in the U.S.A. Although L.H.D. vehicles are the key to the success of the mining method, four other main groups of vehicles are utilised in the mine - trucks, scaling vehicles, ser- vicing vehicles and specialist vehicles. The operating requirements at the C.S.A. mine are more stringent than those encount- ered in many other underground mining oper- ations. The first L.H.D. vehicle used at Cobar - the Transloader - had considerable difficulty in loading and discharging coarse production ore. The Wagner ST5 Scoop Tram performed this duty much better. However, the first generation Scoop Trams were not robust enough to withstand the heavy duty and many modifications were necessary before acceptable availabilities were obtained. Similar modifications were necessary for the Eimco 916 vehicle but the Eimco 915 unit came much closer to meeting the duty requirements. Eventually Cobar technical personnel design- ed a L.H.D. vehicle to meet specific C.S.A. mine conditions. These units have proven most satisfactory. Over 8 years of operation the underground vehicle fleet has become a proliferation of vehicle types. A standardisation pro- gram has been initiated based upon common prime movers being mated with "trailer" units to serve specific functions. Standardisation will reduce inventory levels and facilitate training of operating and maintenance personnel.

Jan 1, 1973

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By M. P. Amsden

"Ecstall Mining Limited, a subsidiary of Texas Gulf Incorporated operates the Kidd Creek Mine, a 10,000 tons per day base metal producer, near Timmins, Ontario. Two different ore types are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall Concentrator the ores are processed by selective flotation in threes individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream x-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8%, zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.INTRODUCTIONSEcstall Mining Limited, a wholly owned subsidiary of the Texas Gulf Incorporated operates the Kidd Creek Mine, one of the world's major base metal producers, near the old gold mining centre of Timmins, Ontario. Discovered in 1964, the property was brought into production in November, 1966. Originally designed for 9,000 tons per day, the operation now treats 10,000 tons per day of two different ore types mined from a single open pit. In the near future, open pit ore will be supplemented by ore from an underground operation now being readied for productionAt the Ecstall Concentrator the ores are processed by selective flotation in three individual circuits. The whole plant is highly automated and control is coordinated from a central control room. The treatment process follows conventional practices although fine grinding is required for optimum flotation recoveries. Normally, two circuits treat copper-zinc ore at a combined rate of 6,500 tons per day while the third circuit treats 3,500 tons per day of silver-lead-zinc ore. Special production averages 2,400 tons per day."

Jan 1, 1973

By Richard L. Fowler

[Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting, obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the bear overage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve completely self-contained shuttle car system which responds to the mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to valuate various guidance techniques during the feasibility study. Subsequent simulation rues were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing wan performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated Chi predicted performance capability during underground face haulage tests. Dust did not Impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance Closed loop steering control with manual override is recommended o: mended for the lateral guidance e system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.]

Jan 1, 1973

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By Zani J. A, Jackson W. D

Bauxite was discovered in the Kimberley in 1965 by an Amax field crew. Reserves of 230 million tons, of bauxite. averaging 47% total alumina on Mitchell Plateau and 980 million tons averaging 36% total alumina on Cape Bougainville have been indicated by the results of drilling and bulk sampling. Laterite which contains the bauxite deposits caps basalt and interbedded sandstone and siltstone of the Carson Volcanics formation. Bauxite on Mitchell Plateau is 3.2 metres thick on average and is underlain successively by nodular ironstone, clay and basalt. The major components of the bauxite are gibbsite,boehmite, hematite and goethite containing some alumina, anatase and clay minerals. Quartz and vanadium oxide are minor constituents. Boehmite and hematite are concentrated near the surface, whereas gibbsite and goethite predominate at depth. The bauxite profile consists of ferru- ginous, pisolitic and gibbsitic zones with increasing depth. Cape Bougainville bauxite is 8.6 metres thick on average and of tubular structure; its mineralogy is relatively uniform..

Jan 1, 1973

By D. F. Strong

Most Newfoundland. mineral deposits can be clearly classified as within rocks formed either as accreting plate margins (ophiolitic pyrite-chalcopyrite massive sulfides such as Betts Cove, Whalesback, York Harbour, chromite at Lewis Hills, and asbestos at Baie Verte), at consuming plate margins (Kuroko-type polymetallic massive sulfides such as Buchans and Pilleys Island, porphyry-type Mo-Cu at Rencontre, fluorite at St. Lawrence), or within plates (zinc deposits at Daniels Harbour, sedimentary iron ores at Wabana, manganese in Conception Bay.) As these metallogenic patterns can be convincingly extrapolated southward into the Appalachians and northward to the Caledonides, they provide an important means of eliminating and selecting areas for particular exploration targets. Sonic criteria are described for the recognition of these environments of differing economic potential.

Jan 1, 1973

By Charles Findlay

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

Although bismuth mineralization is spread widely through the Lachlan Fold Belt in New South Wales, broad grouping of the various deposits can be effected on the basis of geographical and geological (age and type of associated rocks) affinities. As a result, significant concentrations of bismuth can be recognized in the Mid-Western granites, Cobar-type ore, the Yass Silurian acid volcanic belt, and the Albury, Bega, Braidwoodand Bathurst districts.In these deposits bismuth generally occurs in minor amounts associated with molybdenite, wolframite, scheelite, cassiterite, chalcopyrite, galena, magnetite, pyrite, arsenopyrite, and native gold. From this group of minerals three broadly defined associations can be recognized.I. Bi-Sn-W-Mo2. Bi-Au( -Te)3. Bi-Pb-Cu(-Au)There may be some interchangeability of these metals, as instanced by occasional Bi-Cu-W-Mo mirleralization, but pyrite and/ or arsenopyrite are usually prominent in all associations.The first two of these associations occur mainly in the form of narrow quartz veins rarely averaging more than O· 3 per cent Bi, although there is often a marked enrichment in ferruginous material in the oxidized zone.Most of these veins occur within or adjacent to granitic rocks of varying ages (principally Silurian or Devonian), although Bi-Au mineralization tends to be related to more basic igneous activity than the Bi-Sn-W-Mo association.The latter is also occasionally developed in pipes, usually coarse-grained and richer in bismuth (as at Whipstick, the principal mine in New South Wales with a production of 343 tonnes of the metal), or in lower grade, but probably larger tonnage skarn deposits. The bismuth-base metal association occurs mainly in Silurian acid volcanic sequences and may also form low grade but large tonnage deposits, such as is possibly developed at Cobar.

Jan 1, 1973

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

Western Australian tin deposits are similar to those of other Precam- brian terrains in that they are mainly associated with rare-metal pegmatites, in which cassiterite is found with minerals containing any or all of the elements Ta, Nb, Be, Li, Cs, Rb and the rare earths.. They differ from Phanerozoic deposits where cassiterite occurs in quartz veins, greisens, dis- seminations in granite or sulphide lodes, and is associated with minerals containing W, Mo, Bi, Sb, As, Ag, or Cu. The main tin production in Western Australia has come from the Pilbara Block where the more important tin- bearing pegmatites are related to a younger granite phase, and from Green- bushes where large albite pegmatites intrude ?Proterozoic metamorphic rocks. The more important tin deposits in the Pilbara Block, and those in the Halls Creek and Murchison Provinces, are related to granites which are richer in Si and K and poorer in Ca, Mg, Fe and Ti than 'average granite'. The tin granites tend to have higher than average contents of Sn, Rb and Li.

Jan 1, 1973

By Collings P. S, Adair D. L

The Upper Robe (Robe Gorge) deposits occur in Kumina Creek and the Robe River, some 20-40 km upstream from mining operations at Pannawonica. The Gorge Deposits were rec- ognised, mapped and sampled in 1962-3 and re- examined in detail in 1971. Approximately 180 mineralized occurrences were mapped in 1971 on 1:4800 scale and 50 of these were remapped in detail at 1:1200 scale. Eighty cross sections were measured and sampled and 300 geological maps prepared. In addition 88 holes totalling 7388 feet were drilled in three occurrences considered to have the greatest potential. The Gorge Deposits occur in the Robe Pisolite unit which forms thin remnant crusts, bay fillings and occasional cut-off meanders along the edge of the present streams. Less than 50 of the deposits have tonnage potential of one million or more. Consequently exploit- ation of the Gorge reserves must be considered as a very uncertain, long range possibility because the deposits are small and scattered throughout the gorges in the area, thereby necessitating costly railroad spur lines to gain mining access. Grade of the occurrences is extremely variable over short distances both vertically

Jan 1, 1973