Search Documents

This paper addresses the role of mine geology in mining geotechnics. The role is assessed and discussed in terms of five main elements; geotechnical complexity, geological complexity, mine scale, percentage sampling and geological uncertainty. Lastly, the overall objectives and mine geology requirements are listed in terms of the various mine development stages; exploration, feasibility-design and operating.

Jan 1, 1993

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

Pillar mining methods at the Pasminco Mining Broken Hill Operations are not new. Since mining commenced on Pasminco's leases at the turn of the century virtually every pillar extraction method tried throughout the world has been used. Much of the remaining mineral resource in the Pasminco Broken Hill leases is contained in pillars.However, due to the on-going need for mechanisation with bulk mining methods, and the very peculiar physical circumstances surrounding the formation of these pillars, their exploitation requires the development of a virtually new method based on excavation technology not previously used in the Australian mining industry. Trials of the method are to take place at the southern operations during 1991.

Jan 1, 1992

The Hunter Valley Rail Project (HVRP) represents most of the coal producers using the Hunter Valley Rail System in NSW to haul coal to the port of Newcastle. This system carries over 70 per cent of NSW's coal exports, comprising over 30 per cent of total Australian coal exports. Hunter Valley coal is the largest export industry in NSW, and one of its largest export growth opportunities. However, the industry is under intense pressure in international markets from existing and new coal producers and from other energy sources. Whilst potential growth in demand is substantial, particularly for thermal coal in Asia, excess world supply has pushed prices down, and this underlying trend may well continue. The industry has lost international competitiveness and as a result, investment has dropped 44 per cent over the last two years. The industry must be rapidly structured to compete and attract investment on the basis that these pressures will continue. Substantial productivity improvement and cost reductions must be made for the industry to regain competitiveness, otherwise growth will not occur and the industry will decline, with serious implications for the Australian and NSW communities. The introduction of internationally competitive rail freight rates is an urgent and essential part of this process. It is the key objective of the HVRP.

Jan 1, 1995

By Thornton D, Firth B, Kojovic T, Brien G, O&apos

Coal fragmentation is a function of coal type and mining process. Each unit step in the mining, handling and crushing chain of coal imparts energy to the material and impacts on size degradation and consequent mineral matter liberation and pla

Jan 1, 1998

By Jena, Anand S, Das R. P

Leaching studies were carried out on Indian Ocean manganese nodules using sulphuric acid as the lixiviant. By leaching the nodules with 8 per cent sulphuric acid for 12h at 100°C, copper and nickel could be completely extracted along with 50 per cent cobalt and 6.2 per cent manganese.94.2 per cent of the iron was also dissolved. To increase manganese and cobalt extraction, charcoal was used as a reductant. The role of charcoal was to reduce the manganese dioxide and render it soluble as manganese sulphate as well as to facilitate solution of the cobalt minerals associated with the manganese dioxide. Various leaching parameters were studied including acid concentration, amount of reductant, leach time, pulp density and leach temperature. It was found that by leaching the nodules with 10 per cent sulphuric acid at 100°C for 4h using 5 wt/wt per cent charcoal (0.05g of charcoal per g of nodule) almost complete extraction of copper, nickel, cobalt and manganese could be achieved. However, under these conditions all the iron present in the nodules was also leached.

Jan 1, 1989

By Johnson N. W, Quast K. B

Over the years there have been occasional references in the literature to the activating effect of cyanide in galena flotation with xanthates. These have usually been associated with the processing of lead-zinc or copper-lead-zinc ores. Bubble contact curves for the pure galena-xanthate system show a flotation edge at pH 10.4 independent of sodium cyanide concentration which was thought due to hydroxyl ion, not cyanide ion.Flotation tests were conducted on samples of Mount Isa lead-zinc ore using varying concentrations of sodium ethyl xanthate and sodium cyanide. At low collector concentrations, galena recovery kinetics improved with sodium cyanide addition, and the higher the cyanide concentration, the higher the galena recovery rate. At higher collector concentrations, galena recovery rate was independent of sodium cyanide addition.For a given collector addition, the lead grade-recovery curve shifted to an improved position with increasing sodium cyanide level. For the same recovery there was an increase in the lead grade with increased sodium cyanide addition, and this increase was most dramatic at high sodium cyanide concentrations.The presence of sodium cyanide during the grinding of Mount Isa ore caused surface passivation of the iron sulphides and possibly the sphalerite.These sulphides, therefore, reacted with less of the oxygen present in the pulp, hence more oxygen was directed to the surface of the galena. This resulted in an enhancement in the total amount of xanthate adsorbed on the galena that is reflected in the improved flotation response of that mineral.

Jan 1, 1990

By Ellery B. I

Field investigations recently undertaken by Utah Development Company (U.D.C.) have been developed to allow the assessment of ground conditions relevant to the use of large bucket wheel excavators for pre-stripping overburden. "Bucketwheel diggability" predictions were made on the basis of a wedge test which was perform- -ed in the field on nominal 150 mm diameter drill core samples. Specific separation force (calculated from the wedge test results) for different rock horizons were theoretically related to the excavation rates of various sized bucketwheels, i.e., "bucketwheel diggability". The specific separation force was shown to vary with lithology, structure, weathering and moisture changes. By correlating these features between boreholes, an overall assessment of bucketwheel diggability was then made. The approach adopted to assess bucket- wheel diggability incorporated various levels of investigation. Initially, a reconnaissance stage provided information from widely spaced 150 mm cored holes to compare and contrast areas with differing bucketwheel digging char- -acteristics. The following stages progressive -ly added to this information, until finally, between hole correlations, allowed calculations to be made of volumes of materials of similar

Jan 1, 1981

Recent work on computerised mineral resource databases at the Institute of Geological and Nuclear Sciences Limited has concentrated on the development of the GERM, REGCHEM, and MINLIT databases, and their integration in a Geographic Information System using MapInfo software on an IBM-compatible microcomputer local area network. GERM (GEological Resource Map) is a mineral deposit inventory with national coverage and more than 10 300 entries. REGCHEM (REGional Exploration GeoCHEMistry) is a database of stream sediment analyses from open-file mining company reports, containing more than 14 000 sample sites from the Coromandel and west Nelson regions. MINLIT (MINeral LITerature bibliography) is an annotated bibliography of literature on topics relating to the exploration and geology of mineral deposits in New Zealand, and includes more than 5000 entries for published books and papers, and unpublished mining company reports, university theses, and government reports. Master sets of GERM and MINLIT continue to be maintained on a VAX mainframe network but REGCHEM is operated only in the PC environment using the Microsoft ACCESS database management system software.

Jan 1, 1993

By Dutton D

In the British coal mining industry, during the last decade, a great deal of environmental monitoring experience was acquired, particularly in the Doncaster Area of the Yorkshire coal- field, which had a long history of spontaneous combustion and gas emission problems. This paper summarises the experience obtained and shows how the introduction and operation of these systems has resulted in improved techniqu- es for fire detection and control. Some of these systems are described in detail with emphasis placed on the uses to which output data are put, and their impact upon management at colliery level. Reference is also made to the problems encountered in the development of such systems and how they were solved. The paper also makes reference to the recent Research and Development work of the NCB's Scientific Department and Mining Res- earch Development Establishment (MRDE), which was directed to the design and application of a range of underground sensors, and so ensured continuing progress in this field. The paper refers briefly to a new comprehensive monitoring unit and an integrated fire detection and data transmitting system which are currently being assessed in the Yorkshire coalfield.

Jan 1, 1983

By Kay JR

In 1984 a new Regional Geological Mapping Program (RGMP) was commenced by the Geological Survey of Queensland (GSQ); the new program was in response to the withdrawal of the Bureau of Mineral Resources from regional mapping. Areas for mapping were selected in northern and south-eastern Queensland on the basis of potential for mineral discoveries, level of company interest, inaccuracies in the first edition mapping and interests of other organisations (government and universities) in joint projects.Geological provinces of particular interest in northern Queensland are the Hodgkinson Basin, parts of the Georgetown Inlier not covered by earlier BMR-GSQ mapping, Broken River Embayment, Burdekin Basin, Lolworth-Ravenswood Block, Campwyn Block and Anakie Inlier. The 1:250,000 sheets covering these areas of interest are shown in Figure 1 including those already completed, those in progress and those planned for future investigation.A flow chart showing the various phases for RGMP projects is shown in Figure 2. Data collection has two facets: (i) field recording and (ii) office work including air photo interpretation, study of company reports, literature research, petrography and various laboratory studies. Two main strands of information collected are represented by a data base and compilation sheets. Compilation sheets are generally at 1:25,000 scale and are available for purchase. The current data base is very fragmentary and can be accessed only by direct contact with the relevant geologist or via written reports. A more accessible field data base is in the process of being introduced this year; this field data base (REGMAP) is based on standardised data recording and computer storage.

Jan 1, 1986

In 1972, metallurgical testwork on Renison ore indicated a significant proportion of low specific gravity, tin-barren material ideally suited to heavy medium separation (HMS). Further technical and financial studies provided adequate economic justification and in December 1974 the Renison HMS plant was cannissioned. Initial operations were interrupted by the imposition of tin production quotas for three months in 1976; they were also beset with difficulties particularly with regard to mechanical wear. During the first two operating years much develognent work was carried out including installation of a pyrrhotite flotation bank in the medium recovery circuit, investigations into various wear-resistant materials and the use of atanised rather than milled ferro-silicon. By 1977/78 financial year satisfactory performance had been achieved and since then the average floats rejection has been 18.8% of the total ore treated with an associated tin loss of 2.96%. Developnent has nevertheless continued during the last three years, principal modifications being the installation of larger aperture desliming screens and improvements to the overdense cyclone circuit.

Jan 1, 1978

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

Most text books on rock blasting claim that the relationship between burden and borehole diameter is linear. The statistical calculation presented here with real values from one hundred open pit and underground mines indicates that the relationship is exponential. For underground mines the burdens are consistently lower than those for open pit mines because of higher ore densities, greater confinement in blasting, and finally greater demand for well fragmented rock. The results shown in this paper are recommended to be considered in basic teaching of rock blasting technique. The formulas can be used for a first rough estimation of practical burden and spacing. The formulas do not however give any information about the fragmentation. For that purpose it is necessary to use other formulas not described in this paper.

Jan 1, 1990

By Anderson K

In 1991, the first horizontal raise drill hole in Australia was successfully completed by Australian Raise Drilling Pty Ltd (ARD) at the Perseverance nickel mine of Western Mining Corporation's (WMC's) Leinster Nickel Operations in Western Australia. At that time, WMC were experiencing considerable difficulties in developing the horizontal drill drives through the orebody using conventional drill and blast techniques. Following the success of the initial hole, a further two holes were drilled as part of the evaluation program. The technique has proved so successful that it has been accepted by WMC for on-going development of drill drives at Perseverance.This paper describes the program. It relates how the project evolved, the modifications that were required to the equipment used, the performance experienced during the program and the future of the method in this and other applications.

Jan 1, 1993

The construction of mine headframes of reinforced concrete is not a new departure as many structures have been built of this, material particularly in Canada and South Africa. This type of construction has been satisfactorily tested in service and is now accepted by the mining fraternity.The two headframes at New Broken Hill Consolidated Limited are the first structures of this type to be built in Australia, and provide an interesting application of reinforced concrete design and construction.Reasons for Adoption of ConcreteDuring 1947 the writer visited D.S.A. and Canada and inspected three headframes, of reinforced concrete construction.Leading details are as follows:(i) Hollinger Gold Mines. (Timmins, Ontario) : Height of sheaves 110 ft. Shaft has provision for 4 skips each of 12,000 lb. capacity. Structure incorporates surface crushing plant.(ii) International Nickel Corporation-Murray Shaft (Sudbury): Height to sheaves 153 ft. 6 in. Shaft provides for 2-12 ton skips and 2 cages. Surface crushing plant built integrally with frame.(iii) Asbestos-Johns Manviae (Quebec): Height of sheaves 116 ft. Shaft provides for 2 skips 200 cu. ft.

Jan 1, 1956

By Freeman N

A microcomputer based control system has been developed and implemented at ZC Mines (now Pasminco Mining). The control system maximises throughput at a product size set point while maintaining a "safe" cyclone underflow and mill operating pulp density.To characterise mill and cyclone operation over a range of ore types, 60 circuit surveys were carried out by ZC Mines personnel over a period of four months. The data for each test were model fitted to check for data consistency and to accurately estimate circulating loads.The model fitted results were combined with instrument readings (including in-stream analysis probe assays) and the data checked for ability to predict key variables such as product size and underflow density from measurable inputs.In the resulting control scheme, panicle size and underflow density are not monitored directly, but are predicted by regression equation models based on directly measured variables. The tonnage control loop uses a dynamic model to maximise responsiveness.The system provides a data log output to an mM compatible personal computer at programmable intervals. Comparative data logging over a period demonstrates substantially smoothed circuit performance.The grinding control system was originally implemented using Fischer and Porter micro-DCI controllers. The program has also been implemented on a distributed control system using a sequence oriented programming language.

Jan 1, 1990

By J Brisebois

The derelict Lake George Mine is located at Captains Flat in NSW, acommunity of approximately 450, which lies some 43 km southeast ofQueanbeyan. It straddles the Molonglo River, which flows toQueanbeyan and thence the nationÆs capital, Canberra. Catastrophictailings dam failures in 1939 and again in 1943 resulted in the transportand dispersion of thousands of tonnes of sulfidic wastes downstream,with terminal settling in Lake Burley Griffin, in Canberra. The mine wasclosed in 1962, and major rehabilitation in 1996 - 1997 addressed the riskof further collapses, and reduced water flow into the underground mine.Nevertheless, acid mine drainage from the mine, and seepages ofcontaminated water from the capped tailings dumps continue to pollutethe Molonglo River for some 30 km downstream.Environmentally, the highest contributor to the total contaminant loadof the river is the Main Adit Spring. This was shown to be a constantgroundwater-driven acidic flow, with contaminant generation resultingalmost entirely from the ingress of gaseous oxygen into the undergroundworkings. Long term remediation may be possible at source, by pumpingreducing gases into the sealed mine, but the probability of thistechnology succeeding to the required degree is yet to be demonstrated. For at least the medium term, treatment of contaminated water flow(s)will be required to achieve any of the water quality targets that may beapplicable to the river. Three methodologies were short listed, but anumber of strategic uncertainties remain, which the NSW Derelict MinesProgram will address. Future risk arising from long-term contaminantrelease by the treatment wastes must be considered. Appropriate data,and realistic long-term performance parameters regarding the relativestabilities of water treatment sludges are scarce, and make properevaluation of competing technologies problematic.

Jan 1, 2003

By Dyne GD

From experience in the design and operation of power station combustion facilities in most mainland Australian States, involving a wide range of black coals and lignites, and in the specification and procurement of coal supplies for power station use, techniques for the optimisation of coal resource development and power generation utilisation have been developed to ensure compatibility between characteristics of the selected coals and power station design. These techniques include computer data bases for resource data handling and computer simulation of coal-fired boilers for determining coal property cost effects. Data Base Systems allow results of coal analyses to be efficiently handled, to assist in the review of the relevance of resource data to the coal sections proposed to be mined and the coal fractions proposed to be marketed. Data Base Systems also facilitate the marshalling of coal quality data into basic utilisation format to enable a proper utilisation review and analysis of the certainty and scatter of coal properties. Computer simulation of the effects of different coal properties on the capital and operating cost of power stations is achieved by establishing conceptual design parameters of the major items of plant to relate the variations in coal specification to equipment size and type. Variations in power station budget costs can then be determined using the computer model for variations in coal specification.

Jan 1, 1983