Search Documents

By Libby R. Ricafort, Victorio V. Pato, R. S. Pizarro

Introduction Atlas Consolidated Mining and Development Corp. (ACMDC) started gold production at its Masbate gold mine early in 1980. This involved an open-pit mine and a 3.5-k/d (3850-stpd) carbon-in-pulp processing facility (Pizzaro and Antonio, 1981). When this operation started, the mine began stockpiling sub-grade milling material averaging 1 g/t (0.029 oz per st) gold. Furthermore, geologists estimated that there were additional low grade reserves within the ultimate pit limits. These amounted to 2.4 Mt (2.6 million st) with an average grade of 1.1 g/t (0.03 oz per st) gold. The success of low cost heap leaching prompted an investigation to determine if this tech¬nique would be applicable for the low grade Masbate ore. The findings were favorable and a series of laboratory tests were undertaken. These tests indicated the amenability of this subgrade milling ore to heap leaching. Depending on ore size, gold extractions of more than 60% were obtained. To further define operating parameters for a commercial heap leaching plant, a 400-t (440-st) batch pilot plant was built and operated. These test results were used to design the first commercial heap leaching plant in the Philippines. One design concern was the control of solutions during the rainy season. Due to the material's low grade, every effort was made to minimize capital and operating costs. To this end, surplus mining equipment from the copper operations of ACMDC and used machinery in the crushing circuit were considered. Location: The Masbate gold heap leaching operations are located on the northeastern part of Masbate Island, Philippines. This is about 480 km (300 miles) south-east of Manila. Climate: The climate is moderate with two distinct periods. The dry season runs from January through June, and the rainy season extends from July through December. During the wet season, the rainfall at the mine site averages 300 mm/m (11.8 in. per month) for a total of about 2000 mm/year (78 in. per year). However, heavy downpours in excess of 100 mm/h (4 in. per hour) can occur. Geology: Four distinct rock types have been identified in the pit area. They are tuffaceous agglomerates, andesitic agglomerates, metasedimentary rocks, and hornblende augite andesitic porphyry. The tuffaceous agglomerate occupies the northern and western flanks of the mine. Andesitic agglomerates are localized distinctly in the central portion of the volcanic plug within the mine site. The eastern boundary of the mine is occupied by metasedimentary rocks, whereas, the hornblende augite andesitic porphyry occurs as an intrusive within the andesitic agglomerate and tuffaceous agglomerate. Some areas of the pit contain high proportions of clay minerals, requiring an agglomeration step in the flowsheet. This ensures satisfactory percolation through the heaps. Ore characteristics: Gold and silver are microscopically dis-

Jan 9, 1987

By Wilbur Nelson

IN 1839,1 Gerard, Troost, the first, State Geologist of Tennessee, reported the occurrence of zinc ores in East Tennessee, in connection with the iron ores at Embreeville; in 1844,2 he refers to the zinc deposits of East Tennessee, especially the apparently rich deposits occurring, in Jefferson and Claiborne Counties, while his ninth annual report is a ,description of the zinc deposits of Jefferson County and a description of the most improved processes by which zinc is extracted from its ores. Although. Tennessee has long known of the occurrence of its zinc deposits and has recognized their value, only during the last few years have these ores been successfully worked. As far as can be learned, prior to the systematic development of the Mascot district in 1911, no large-scale or successful operation of any of the zinc deposits was carried on. But in that year, after several companies had made considerable progress in developing the Mascot area and had proved. a relatively extensive body of low-grade sulfide ore, the American Zinc Co. entered the field. It introduced modern methods of prospecting and mining the ore and from the first was successful. Too great credit cannot be given this company for its pioneer work in a previously unimportant field. Throughout the history of its operations, the American Zinc Co. has confined its efforts to underground mining of the sulfide ore, sphalerite. This company has found that successful results in zinc mining in East Tennessee can be achieved only by expending large sums in prospecting and blocking out bodies of pay ore in sufficient magnitude for large-scale operations. At Mascot are located the mines of the American Zinc Co. of Tennessee, the mines being situated along the Southern Railway in the Holston River Valley, Knox County, about 13 miles northeast of Knoxville. Considerable mining and prospecting had been done by several companies prior to the acquisition of this property by the, American Zinc Co. Previous to 1900 only open pits, which were worked for oxidized ores, were operated. and the production was small. In 1900 the

Jan 10, 1924

By F. B. Samani, B. Stabel

The 1,000 MW Hydro Power Station Masjed-e-Soleiman (formerly called Godar-e-Landar) in Iran is under construction since 1992. The rock engineering aspects of the major underground structure, i.e. the powerhouse cavern shall be reported on in detail. The geotechnical investigations are described and results given. The results of several geotechnical analyses are presented. The designed and executed rock support is given. A description of the monitoring systems and typical measurement results obtained during and after excavation are presented. The lessons learnt during construction of the Stage-I powerhouse cavern were applied on the extension of the powerhouse cavern, which is to house an additional 1000 MW. Details regarding the unexpected behaviour of the Mudstones are given. Die 1000 MW Wasserkraftanlage Masjed-e-Soleiman (vormals Godar-e-Landar genannt) befindet sich seit 1992 in Bau. Dieser Artikel berichtet im Detail über die felsbaulichen Aspekte der Untertagebauwerke, insb. der Maschinenkaverne. Die geotechnischen Untersuchungen werden beschrieben und deren Ergebnisse wie die Ergebnisse verschiedener Berechnungen werden präsentiert. Die geplante und die ausgeführte Felssicherung wird angegeben. Die eingebauten Überwachungseinrichtungen werden beschrieben und typische Ergebnisse während des Aushubs und danach werden dargestellt. Die Erfahrungen beim Aushub der Kaverne der Stufe I wurden beim Entwurf der Kaverne der Erweiterungsstufe II, die weitere 1000 MW beherbergen wird, berücksichtigt. Details zum unerwarteten Verhalten des Schluff-/Tonsteins werden angegeben. La centrale hydroélectrique de Masjed-e-Soleiman (dénommée anciennement Godar-e-Landar), d’une puissance de 1.000 MW, est en construction depuis 1992. Un rapport détaillé sera présenté sur les aspects relatifs à la construction en enrochements de l’aménagement souterrain principal, à savoir la caverne abritant la salle des machines. Une description des investigations géotechniques réalisées y est fournie ainsi que les résultats correspondants. En outre sont présentés les résultats de plusieurs analyses géotechniques. L’ancrage dans la roche tel que projeté et réalisé est présenté. Une description des systèmes de contrôle ainsi que les résultats de mesures typiques obtenus au cours des travaux d’excavation sont donnés. Les leçons tirées lors de la construction de la Phase 1 de la caverne de la salle des machines furent appliquées à l’extension de la caverne de la salle des machines, qui doit abriter une unité supplémentaire d’une puissance de 1.000 MW. Par ailleurs, des détails sont donnés sur le comportement inattendu des argilites.

Jan 1, 2003

By P. Duran

The metallurgical gas handling system at Chagres Smelter, like that of many smelters, can be the limiting constraint to processing more concentrate through the smelter. Mass and energy balances for the metallurgical gas handling system processing off-gases from the flash furnace and Peirce-Smith converters have been used by both operations and process engineering groups to help evaluate different operational scenarios in which the use of the installed capacity could be maximized and/or an operational strategy can be change with the purpose of removing a bottleneck or justifying an investment to relieve a constraint in the gas handling system. The present work describes the development of these process balances that were carried out in Exce®. The results were validated with operational data and, subsequently, some cases of industrial interest were simulated, detecting some conditions that were limiting the operation due to the present installed capacity in the Chagres Smelter.

Jan 1, 2007

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By C. R. Larsen, R. G. Bradburn, A. L. Mular, B. C. Flintoff

"Following the acquisition of grinding- circuit data at Brenda Mines Limited for simulation purposes, various methods to mass balance the circuit were evaluated. Unfortunately, different answers were obtained for different balancing methods. A data-adjustment procedure was therefore developed. The procedure assumes that all ""best-fit"" criterion. A search is conducted with the minimum set of water masses and narrow size ranges of solids around the circuit (called search variables), which permit the computation of any of the measured data points. Search variables are used to calculate measured values for an objective function of the form: [ ] where W, is a weighting factor•, M1 is a measured value and M. is a corresponding . value calculated from search vanables. The best values of M, are those which minimize R. The above method is compared with others that have been utilized for mass balancing circuits."

Jan 1, 1976

By R. Tipman, T. C. Burnett

"A general computer program has been written to calculate material balances using multiple regression techniques. The program can handle metal assays or size distribution data obtained in multiple surveys of the flotation circuit. The ""best fit"" weight split is calculated between the input and product streams by minimizing the sum of squares of the residual errors using all of the available data. The program includes an assay adjustment feature in which each assay is recalculated to fit the ""best fit"" mass balance. Thus assay or sampling errors can be easily identified. Also the assays can be statistically weighted so the most precise measurements are given the most influence on the material balance. The computer output reports the mass balance, the actual and corrected assays, the percent metal recoveries and the significance and confidence levels for the weight splits.The program enables a rapid and accurate evaluation of mass balances from large masses of data obtained in multiple surveys around a flotation circuit. The effects of changing process variables can be quickly evaluated with statistical confidence."

Jan 1, 1978

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer'. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By G Kennewell

At 11 am Monday 8 September 1997, the successful detonation of the 5/9 Mass Blast at Pasminco - Elura was signified by the subsiding of æMt KevinÆ (a 15 m high earth fill mound). The blast was in response to earlier mine subsidence, which holed through to the surface affecting future stability of underground workings. The blast was a first for Elura which fires small tonnages regularly to avoid rapid oxidation of the ore. This paper discusses the strategy and the considerable planning that went into EluraÆs first blast of this magnitude in order to succeed first time round.

Jan 1, 1999

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

Traditional loading systems have relied for many years on wheel and track loaders, power shovels, conveyor belts, and more recently, hydraulic front shovels. Each has certain advantages and disadvantages, depending largely on job conditions. Hydraulic backhoes were introduced several years ago as still another truck loading option. At first, buckets were small and backhoe use was limited to small earthmoving projects. Now, as backhoes are equipped with shorter sticks and bigger buckets to move larger quantities of earth. The "mass excavation" concept offers an excellent truck loading option in many situations. System Development and Advantages Mass excavation was first used successfully by contractors in site development and highway construction, loading both on-highway and off-highway trucks. Operators were able to take advantage of the excavator's ability to work in poor underfoot conditions and dig in tough materials. The technique was first applied to mining in the kaolin mines of central Georgia. Kaolin, one of the world's most abundant minerals, is used to make paper, paint, ceramics, rubber, plastics, and many other products. Since kaolin clay is slippery when wet, load-out with wheel loaders is very inefficient. Also, kaolin is found in very spotty deposits due to the weathering process involved in its formation. Consequently, draglines are also impractical for kaolin mining since they don't have the mobility to move between clay deposits. In response to these mining conditions and kaolin characteristics, mines began using excavators in mass excavation as early as 1976. They have developed a system that takes advantage of the excavator's •high penetration and breakout force in tight materials; •fast-cycling hydraulics; •ability to work in poor underfoot conditions; and •mobility in comparison to draglines. This loading method has been successful in Georgia's kaolin mines and now can be applied to other mining operations as well. The excavator's ability to carefully dig spotty ore deposits is an asset at uranium mining operations. Any mine can take ad-

Jan 3, 1982

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By C. Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in the flotation circuit were calibrated using a dynamic grinding/flotation simulator. Predicted values are multiplied by g/t ratios to calibrate reagent flow. The transfer functions are currently integrated into the distributed control system at Les Mines Selbaie.INTRODUCTIONThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970's there have been numerous publications dealing with practical applications of flotation process control. A review of that literature shows that basic feedback and feedforward controls are the two preferred strategies for flotation processes. Some advanced control schemes started to emerge (e.g. Zaragoza and Herbst, 1988). Feedforward and feedback aim at reducing the effect of the following flotation process disturbances (e.g. McKee, 1991):0 Changes in throughput;0 Changes in feed grade;0 Changes in particle floatability (size, liberation, surface oxidation ... );0 Deliberate changes of set-point;Feedforward strategy acts on manipulated variables, mainly reagent addition, to attenuate the effect of disturbances such as changes of feed rate and grade. The feedforward strategy is driven by measurements of disturbances. Feedback control acts to compensate unmeasured disturbances, such as ore floatability, and to bring process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by set-point error, caused by either a deliberate change of set-point or unaccounted disturbances.This paper proposes a way to improve feedforward control schemes by addition of a simple model of solids transportation. The feedforward strategy considered in this paper is of ratio type, i.e. the manipulated variable is changed according to a predefined ratio between this variable and the measured disturbances. A typical example is the ratioed reagent addition to mass flow of ore."

Jan 1, 1993

The Estonia Mine, operated by Eesti Energia Kaevandused AS (EEK), the mining division of the Estonian Government's energy company, Eesti Energia AS, is a large room and pillar mine located in Eastern Estonia. It supplied approximately 4.9 Mt/a of oil shale in financial year ending 2010, which is used for electricity and shale oil generation. Due to the Estonian climate and the power station's need for a dry product, Estonia Mine has developed a planning system where short-term demands of the power stations dictate the schedule. Such an arrangement requires maximising flexibility and consequently the mine only operated for 199 days in 2010.The footprint plays a key role in achieving mass mining rates as the 12 km + 12 km lease area allows the mine to split into mining districts that act independently of each other and maximise the number of work areas available. Coupled with this, the geology of the mine is relatively homogenous over the mining lease, simplifying the mine design and production methods.During the last five years, EEK has commissioned a comprehensive conveyor network. Consequently, material handling only requires loaders to dump oil shale direct from the production face onto a chain conveyor that feeds the conveyor network that ultimately supplies the enrichment plant. Dewatering is also of critical importance, with 90 Mm3 of water discharged annually. EEK uses large trenches up to 3.5 m deep and 1.2 m wide to channel groundwater. Track mounted mechanical saws are used to cut slots in the floor, to control overbreak in blasting these trenches.EEK has introduced Salzgitter Machinenbau GB 280S auger drills that drill three 280 mm diameter holes simultaneously. This has improved void hole drilling times and reduced the drilling required for each face, reducing the overall production cycle time. Blasting activities have also been decoupled from other mining activities negating the need for firing times through the use of small independent firings, required to control vibrations.

Dec 6, 2010

By R. M. Caitlin

QUITE a number of years ago in looking for basic facts, it seemed obvious, in view of an unquestion-able supply of raw material and an extensive requirement probable in the near future, that the funda-mental requirement of any shale-oil industry was mass production 'by a continuous process. This decision greatly simplified matters, as it eliminated all considera-tion of externally-heated retorts, and all batch processes, which only utilize a part of the capacity of the interior space because, unless the ashes are removed as rapidly as formed, the space occupied by them is dead, instead of being occupied either by shale in active distillation or in drying out and heating up preparatory thereto. A second imperative and basic necessity soon appeared as a natural sequence, namely, the fixed carbon of the spent shale must be utilized to supply the heat for the eduction of the oil. PRODUCTION OF THE CRUDE As the production of the crude oil is the first and most important step in the utilization of oil-shale, being the only source from which the multitude of possible by-products can come, each by a special treatment of the crude oil, I will devote the time allotted to me to the subject of crude oil production-its cost expressed in terms of tons treated per man per shift. The costs of mining the shale and refining the crude shale oil vary with local conditions and are not specially influenced by the source of the crude. But the cost of distilling the shale in terms of tons per man shift seems to be the basis of any proper comparison of costs. After considerable experimenting, ranging from laboratory tests up to and including quantities of fifteen to twenty tons, it was evident that a plant might be made up of an indefinite number of units operating in concert. The economic size of the units, however, would .have to be determined by experiment. The general theory of our process contemplates a regulated combus-tion of the fixed carbon in the spent shale, in its incan-descent condition after all the oil has been driven out of it; and a transfer of the resultant heat to the mass of raw shale above.

Jan 1, 1927

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974

By Kumar M. Lyer

The channel reactor for ferrous and nonferrous processing has been modeled as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength submerged gas injection. A composite model has been developed which describes the mass transfer between the two liquid phases, including the transfer of minor elements. The residence time for the matte droplets in the matte/slag emulsion is compared with the settling rates for the matte droplets in the slag to determine their relative importance in the mass transfer between matte and slag. The governing equations for mass transfer have been developed using correlations for the mass-transfer coefficients in the continuous and dispersed phases. An application of this scheme to a typical copper smelting system is presented.

Jan 1, 1993

By J. K. Brimacombe, F. D. Richardson

Studies have been made of interfacial turbulence occurring in reactions in which indium, zinc and cadmium, dissolved in amalgams, are oxidised into aqueous phases by ferric or mercurous ions. It has been found that this turbulence occurs when the concentrations of oxidising ions in the aqueous phase become sufficiently great. These concentrations are the same as those at which the mass-transfer coefficients in the aqueous phase increase sharply when both phases are stirred by gas bubbles rising through them. The effects of gas flow rate on the mass-transfer coefficients for zinc in mercury have been established, and the oxidation of pure mercury has been investigated. The relevance of the work to processes involving liquid metals is discussed

Dec 1, 1971