Search Documents

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

In September 1985, the Chairman of the Transportation, Aviation and Materials Subcommittee of the House of Representatives requested that the Director of the Bureau of Mines address the issue of South Africa and critical materials dependency in testimony before the Subcommittee. Subsequent to the testimony, the Bureau has prepared a technical report focusing on the importance of South Africa and, in some cases, its neighboring countries as suppliers of six key materials. The report includes a qualitative analysis which examines the supply shortfall resulting from a potential disruption, options that are available for mitigating the impact, and their likely effectiveness, and quantitative analyses which estimate the economic impacts in the chromium and manganese markets resulting from peacetime disruption scenarios specified by the Subcommittee Chairman. The concluding section treats the role and capabilities of the Bureau of Mines in dealing with mineral supply disruptions.

Jan 1, 1986

By J. W. Merkley, K. B. Hustwick

"The authors describe the use of a computer system for the control oj warehouse inventory at Cominco's Canadian operations. The challenge presented by the company's diverse products and various locations necessitated a practical approach to operational and manpower requirements. The utilization of modern forecasting techniques, manual intervention and exception reporting provides system flexibility. The system also provides both operational and management control to set required service goals at the lowest inventory levels for inventory management.IntroductionCominco Ltd. is a Canadian company, with international operations, the principal business of which is zinc, lead and chemical fertilizer s. Its involvement is fully integrated and range s from mineral exploration through mining, smelting, refining and by-product production to international marketing. It also embraces related services, including trade, wharfarge and power. With head office in Vancouver, it is involved, directly or through subsidiary or associated companies, in Canada and in the United States, Greenland, Europe, Australia, India and Japan.Cominco has over 12,000 employees and 26,000 shareholders, with 91% of all shares held in Canada.Cominco's Inventory Control System is one of the most extensively used computer systems employed by the company. Also, inventory control is regarded as one of the most economically successful computer applications to be undertaken by the Data Processing Services (D.P.S) Group that was responsible for the development of the Inventory Control System.The main use of automatic inventory control has been at operating plants in Western Canada and the Northwest Territories, which are separated by large distances. Each location has equipment-intensive mining and processing operations and it is essential to maintain control of parts and supplies inventories. Some of these locations are remote from urban and industrial centres and it is important to avoid the adverse effects of high personnel costs and re-training due to turnover."

Jan 1, 1982

By Otto Ruhl

The Oronogo-Webb City-Duenweg district is in the northeastern part of the Tri-State zinc and, lead field. Its metal-mining history dates from the early 1850's. For some years prior to 1918 it ranked as the leading producing area of the entire Tri-State field, but by 1920 most of its mines had been abandoned and allowed to fill with water. Its mine operators had-been attracted, to the newly discovered and richer deposits around Picher, Okla. In 1943, the Orenogo Mutual Mining Co. was exploiting the Oronogo Circle deposit in the northern end of the district, and the Federal Mining & Smelting Co. was preparing to mine on its holdings in the southern part near Duenweg. The area between these two operating units ranked as the largest single block of ore reserves under water in the Tri-State field. In 1942, engineers of the Bureau of Mines, in collaboration with the William Stewart Engineering Co. of Joplin, collected all available mine maps, mine reports, and logs of old drill holes in the inundated area. From a careful study an appraisal of these data, the reserves in the block were calculated at 20,647,800 tons of ore containing 606,440 tons of 60-percent zinc concentrates and 46,970 tons of 80-percent lead concentrates. The ore was estimated to contain 1.76 percent recoverable zinc and 0.18 percent recoverable lead.

Jan 1, 1949

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002

By Jack Eloranta

Optimization of blasting requires the comprehension of processes including drilling through milling. The author has previously considered the role of powder factor in relationship to downstream processing costs. Recent modeling done by Lownds provides improved prediction of fragmentation based on the distribution and level of blast energy. Many recent studies have indicated improved downstream costs due to higher powder factor. However, changes in powder factor are accompanied by changes in pattern. The purpose is to segregate the effects of higher powder factor from powder distribution. This paper will attempt to use typical Mesabi Range iron ore parameters and costs to illuminate the subject of total process optimization.

Jan 1, 2001

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Erika Gusmão, Daniella Cardoso Buzzi, José Roberto de Oliveira

"This study evaluated the Salvinia sp action on metals biosorption in a synthetic sample of acid mine drainage (AMD) in order to determine the time and amount of metals uptake. Biosorptives tests were realized varying the contact time of 5, 20, 60 and 240 minutes. And keeping constant the follow parameters: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). In order to quantify the metals concentration captured by biomass, the AMD samples will be analyzed by ICP. Biosorbent, Salvinia sp., will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. The infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests.IntroductionThe current emphasis on environmental sustainability leads the industry in general, to treat their waste. The human activities are increasing, highlighting the industrial and mining activities, and have promoted the contamination of soil, waterways and groundwater by metals (1). The waste must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.This means the importance of studies of economic and effective methods to eliminate these metals from wastewater generated. The bioindicators are good investments in this area. The aquatic weeds are plants that inhabit swamps up from truly aquatic environments. They have several morphological and physiological adaptations that enable them to colonize the various aquatic environments. They are used as bioindicators of water quality and have also been used in decontamination of aquatic environments, production of biomass for livestock feed, fertilizers, soil and fish tanks (2)."

Jan 1, 2012

By J. Ritchey

This report describes the engineering feasibility and economic advantages of using a mobile bridge-type cross-pit belt conveyor system in conjunction with a large dragline to excavate and transport spoils in a typical Western surface coal mine. The studies show that such a system could be built to survive operational and climatic mining conditions, and that its implementation would offer a reduction in both acquisition and operating costs versus conventional mining units of comparable rapacity. Reclamation costs can also be significantly reduced, and the total reclamation process accelerated, making the cross-pit conveyor system attractive to mine Owners and environmentalists alike.

Jan 1, 1976

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of tie Bruneau River and Jarbidge River study areas, Owyhee County, ID, for the U.S. Bureau of Land Management. The study areas, separated by a narrow corridor, include 90,000 acres of the 107,020-acre Bruneau River Wilderness Study Area (ID-111-17) and 47,000 acres of the 75,340-acre Jarbidge River Wilderness Study Area (ID-17-11). They lie 26 miles and 55 miles, respectively, due south of Mountain Home, ID. Approximately 38 placer claims for gold and 182 lode and placer claims for jasper, agate, and limestone were located within and adjacent to the study areas from 1893 to 1981. Currently, there are eight mining claims for jasper at Indian Hot Springs along the corridor between the study areas.

Jan 1, 1987

By G. Konstantopoulou

Environmental degradation due to abandoned quarries is an international problem, more intense when these sites are found in urban or suburban zones, in environmentally sensitive areas or are visible from sites of special interest. Rehabilitation solutions applied worldwide, range from simple relief restoration and planting to more sophisticated site exploitation in order to serve specific social needs. The elaboration of rational rehabilitation plans for every site presupposes deep knowledge and comparative evaluation of all the parameters of the problem. In this paper, a methodological approach of rehabilitation solutions for abandoned quarry sites is elaborated, based on domestic and international experience and practice. Solutions are grouped in eight main categories. In every category the framework of prerequisites and confinements (environmental, technical, social, economic, legal) for their application in Greek quarry site is investigated. A comparative assessment of alternative restoration solutions is introduced, using tools supplied by environmental economics, cost-benefit analysis, G.I.S. and multi-criteria analysis and follows in two stages: 1) Establishment of a set of criteria aiming at a priority list for a number of quarry sites located in a geographical or administrative district. 2) Assessment of alternative solutions for every single quarry from the previous priority list for the selection of the most adequate using technical, economical, social and environmental criteria.

Jan 1, 2008

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By Edwin Ludlow

THE responses to the request of the Finance Committee have been coming in with gratifying results, .but there have also been about a dozen letters received objecting in various ways to the voluntary subscription. These can be summarized as: First.-That the dues should have been increased, and thus impose the same burden on everyone. This would not have met the present situation, as under the constitution no increase could be effective until 1922. Second.-The Institute should 'live within its means, and reduce its expenses to correspond with its income. As far -as possible this was done by deferring the publication of Volume LXIV until 1921, although the papers published in that volume, were presented at the meeting in February, 1920. It is to avoid being obliged to do this again that the subscription is asked, as we feel that it is, a duty we owe to our membership_ to give them the papers presented at as early a date as possible.. Our financial situation is due to the very large increase in the cost of publication; owing to the high price of paper and printing. The cost of paper is now decreasing, and we hope that there will be' wage adjustments that will permit a lower cost for printing. Under present conditions each volume of our TRANSACTIONS costs three times as much as it did in 1917 and we would be able to publish only one' volume per year. Third.-That there are too many papers published that are 'of no interest to the writer of them .complaint.-This is undoubtedly true, but it must be remembered that the membership of the Institute includes all branches of mining and metallurgy and that all these branches are entitled to be' represented in our TRANSACTIONS by papers.

Jan 1, 1921

By David Wright, Jerome Chamfray, Anthony Harding, Brian Boye

Conway’s Law states that unless we intentionally design automation tools around what we need, we will simply replicate our existing processes. While we may achieve some savings this way, there is an opportunity for greater benefits if we re-imagine the way we, as an industry, perform design. This paper examines current technology and shows how even small departures from merely encoding what we currently do could reap significant benefits. From these examples a framework is developed for a new and innovative approach tvo automation that will allow us to design more quickly, to a higher quality, and communicate outcomes more effectively.

Dec 1, 2022

By Yao Yevenyo Ziggah, Victor Amoako Temeng, Solomon Evans Kweku Koomson

Tyre hours/life deficit is a major operational challenge facing the mining industry which adversely affects materials production and costs. An accurate forecast of the tyre life is key in addressing this menace. This study for the first time employed the hybrid intelligent technique by utilising three metaheuristic optimisation algorithms, including particle swarm optimisation (PSO), genetic algorithm (GA), and whale optimisation algorithm (WOA), as trainers for the parametric weights and biases to optimise multilayer perceptron neural network (MLPNN) for enhancing prediction of on-site dump truck tyre life in the mine. Four hybrid models known as PSO-MLPNN, WOA-MLPNN, GA-MLPNN, and BP-MLPNN were developed using a total of 157 tyre dataset records obtained from a surface mine in Ghana. In assessing the prediction performances for the models developed, five statistical performance metrics of variance accounted for (VAF), Nash–Sutcliffe efficiency index (NASH), coefficient of determination (r2), mean absolute percentage error (MAPE), and correlation coefficient (r) were utilised. Moreover, ranking, uncertainty analysis and Bayesian information criterion (BIC) techniques were utilised to establish the most effective hybrid model, whereas sensitivity analysis was conducted on the input parameters. Results achieved showed that PSO-MLPNN was the best for prediction because it had the least MAPE value of 1.196% and relatively high values of VAF (99.642%), NASH (0.996), r2 (0.996), and r (0.998). Besides, PSO-MLPNN had the best selection criteria values of 6, 7.1725, and 444.834 for the ranking, uncertainty analysis and BIC respectively. Hence, PSO-MLPNN is recommended for the prediction of on-site dump truck tyre life for the studied mine.

Mar 11, 2024

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Ohio using a large stripping dragline, and truck and front-end loader (FEL) is described. The specific objective of the study is to demonstrate the application of the simulator to mine planning and coal production. On the basis of the simulations, it was concluded that the production from the haulback operation should be increased to accommodate improvements in both the stripping dragline's availability and mean cycle time. Several alternatives were studied for the best use of equipment if the present operating parameters could not be improved upon. No economic analysis of these proposals were made.

Jan 1, 1977

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By O. E. Kiessling

THE Committee-on Production Control, at its meeting held during the last annual session in February, 1930, evidenced great interest in problems of stabilization affecting all mineral industries. . No immediate program of activity for the Committee as a- unit was decided on, however,, and efforts during the past pear have consisted lirgely of further stressing the economic aspects of mineral production and of the action by committee members, :.serving in their individual capacities, in sponsoring constructive changes, in specific, industries. Of greatest interest to the general subject of production control in 1930 was the very definite advance toward better coordination of demand and supply in the petroleum industry. Furthermore, since opinion both within and without the oil industry now favors a constructive program, and with a gradual change in legal precedents, it seems not unreasonable to expect greater progress in the near future.

Jan 1, 1931

By E. Petrakis, K. Komnitsas

The main objective of batch grinding modeling is the estimation of the product particle size distribution over time or specific energy input to the mill. So far, the developed analytical methods require often complicated calculations which are timeconsuming. Thus, more simple approaches that allow the reliable prediction of the complete product size distribution need to be developed. In the present paper, an approach, based on the population balance model (PBM), that reliably predicts the product size distribution is proposed. In order to enable this, the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (R-R) distribution, thus allowing the determination of the breakage rate for each grinding period. A time-dependent breakage rate framework was developed where the traditional linear theory of the PBM is considered a partial case. This approach allows the deviations from the linear theory to be categorized and the degree of the acceleration-deceleration of the breakage rate to be predicted. Modeling results were validated by laboratory grinding studies using two homogeneous materials, quartz and marble, and one heterogeneous, a limonitic laterite. The experimental data revealed that grinding exhibits non-first-order behavior and the degree of deviation from the linear theory depends on the tested material. The reliability of the proposed model was validated with the use of the distribution modulus n, the a value of the breakage rate parameter, and the optimum n values that minimize the sum of the differences between the experimental and estimated particle size distributions.

Feb 8, 2021