Search Documents

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In order to make full use of the chromium-bearing vanadium titanium magnetite with chromium, a new process of “direct reduction-electric furnace smelting separation” has been developed for recovering the iron, vanadium, titanium and chromium in recent years. In this paper, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the reduction degree of Fe, V and Cr with different n C/nO (mole ratio of carbon and oxygen). It was found that the suitable operating conditions of direct reduction process were n C/nO > 1.07 and T > 1473 K. In addition, the direct reduction experiment of Hongge vanadium titanium magnetite was carried out and the obtained samples after direct reduction were analyzed by XRD and chemical composition. The result shows that the metallization rate of carbon-containing pellet is nearly 90%.

Mar 1, 2018

By Xueqin Li, Xuewei Lv, Yu Zhang, Wenchao He

In recent years, a new process of “direct reduction-electric furnace smelting separation” has been put forward and developed for recovering the iron, vanadium, titanium and chromium to make full use of the chromium-bearing vanadium titanium magnetite. In the present work, FactSage, one of the most frequently-used thermodynamic calculation software, was used to calculate the migration of Fe, V, Cr and Ti with different nC/nO (mole ratio of carbon and oxygen). The calculation results indicate that the recoveries of Fe, V and Cr increase with increasing nC/nO and temperature respectively. In addition, the recoveries of Fe, V and Cr are up to 90% when the nC/nO value is more than 1.15.

Mar 1, 2018

By W. E. Wallace, J. A. Warren, D. Josell, D. Wheeler

"We present the results of experiments and modeling of flip-chip geometry solder joint shapes under shear loading. Modeling, using Surface Evolver, included development of techniques that use an applied vector force (normal and shear loading) as input to determine a vector displacement of the pads connected by the solder joint (standoff height and misalignment). Previous solutions solved the converse problem: fixed displacements used to determine required applied force. Such solutions were inconvenient for applications, where the applied force (chip weight) is known. Also, for geometric and materials studies of solder joint shapes involving multiple parameters, determining the equilibrium displacement from applied force by bracketing solutions could become computationally expensive. Measurements of solder joint standoff height and misalignment as functions of the applied force (normal and shear), solder volume and pad diameter are presented. Experiments were carried out for solder ball diameters from 0.38 mm (0.029 mm3 volume) to 0.15 mm (0.0019 mm3 volume) on pads of diameter 0.64 mm and 0.35 mm. Fitting of simulation to experimental results gave optimized values for the contact angle and surface tension of the solder which were consistent with measured and literature values. IntroductionIn packaging technology flip-chip has become an important method for attaching semiconductor devices to substrates. Generally, the chip and substrate are bumped with solder and then the chip is flipped onto the substrate and the solder reflowed to form conductive interconnects. An epoxy underfill is normally flowed between the substrate and chip to reduce the thermal fatigue on the solder joints. A flip-chip assembly is illustrated in Figure 1.In flip-chip applications, the use of an integrated underfill/solder bump system [1, 2) removes an extra process step, namely infiltration of the underfill. However, the presence of an underfill will retard the self-alignment of the flip-chip. A first step in understanding and predicting this retardation is to develop a model to describe normal and lateral force-displacements curves when underfill material is not present. At this stage it is unclear whether static surface tension theory is sufficient to describe a complete model for flip-chip realignment even without underfill."

Jan 1, 2001

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017

By Shusen Cheng, Kun Yan

An elastic-plastic stress mathematical model of hot blast stove shell has been established in order to investigate the stress distribution and deformation of the shell. The results show that stress concentration happens along the intersection line of hot blast stove body and the hot blast manifold. The plastic deformation occurs on the hot blast outlet in blast period. The deformation degree of the hot blast shell near the blast outlet in blast period is much larger than that in combustion period. In blast period, the shell near the blast outlet elongates along the horizontal direction and shortens along the vertical direction, the shell near the outlet deforms into an oval. And in combustion period, its deformation isn’t obvious. The repeated deformation of the shell near the outlet between different periods may cause the refractory brick damage and be harmful to the long campaign life of hot blast stove.

Mar 1, 2017

By Stober, Frank Allan

The paper describes the development of components in an lntegrated Furnace Control system for shielded-arc smelting focusing on operation and crucible integrity enhancement. The paper reviews the mechanisms of power, feed and energy input and losses into the shielded-arc smelting process and describes the furnace control system module development and integration to tailor the process. The ultimate success of a furnace control system application is transfer of knowledge, training, and operational support during furnace start-up and ramp-up phases and a model for how this has been achieved is discussed. The control modules of a shielded-arc laterite smelting furnace are described in detail including measured results and screen captures from application in a laterite smelting furnace. This paper focuses on developments in Integrated Furnace Controls tailored to shielded-arc laterite smelting but development of common furnace control modules for improved crucible and tapping operation integrity applied to other furnace processes, including immersed-arc smelting, is also covered. Keywords: IFC, Power, Feed, Supervisory, Control

Jan 1, 2004

By Pan Gu, Zhen Zhang, Wen-Feng Tan, Jiang Diao, Bing Xie, Wang Zhou

In order to recover the chromium resource in chromium-containing vanadium extraction residue, a promising method is to prepare ferrochromium with the residue. The synthetic residue has been reduced under 1300, 1350 and 1400 °C at the reduction time of 1, 2 and 3 h respectively. The reduced samples have been smelted and separated by an induction furnace. The contents of chromium and iron in metallic phase have been determined by an inductively-coupled plasma spectrometer. The results indicate that chromium iron carbide (Cr, Fe)3C7 is the intermediate phase and titanium oxides have been reduced during the reduction process. While the sample has been reduced under 1400 °C for 3 h, metallic phase becomes the dominate phase and reduction reactions almost complete. Moreover, the chromium content in the metal phase reaches 10.19%.

Mar 1, 2017

By Xuyang Liu, Xuewei Lv, Yu Zhang, Xiaolong Wu, Chunxin Li

Titanium nitride is a broad-spectrum specific functional material because of its many superior properties. Therefore, it is necessary to investigate synthesis methods of TiN and alloys containing TiN reinforcement. In the current study, with the increase of nitrogen gas pressure and the optimization of routine ball milling parameters, the conventional mechanical ball-milling method can be improved, the nanometers TiH2-TiN composite powder can be synthesized successfully in a shorter time. Nitrogen gas filled in ball mill jar in which the pressure was 0.6 MPa. TiH2 powder was milled under nitrogen atmosphere at a spinning rate of 250 rpm. The results show that the stable TiN is formed after grinding for 2.5 h according to the X-ray diffraction pattern. DSC (differential scanning calorimetry) curves also indicate that milled compound powder adsorbs certain nitrogen gas. The gas adsorbed in TiH2-TiN composite can exist stably below 200 °C.

Mar 1, 2017

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By J. Sofra

The quantity of copper produced by secondary material processing is increasing as metal producers look to cleaner and cheaper sources of copper. The need to smelt secondary copper more economically, to process a wide range of materials with large fluctuations in size and composition and to cope with the increasingly stringent environmental constraints have put considerable pressure on existing conventional secondary copper smelters. The Top Submerged Lance process, developed and commercialized by Ausmelt Ltd offers a low cost technology, which is particularly adapt at processing copper-bearing scrap and residues. The application of Ausmelt Technology to replace conventional secondary copper processing operations introduces potential for significant advantages in environmental performance, and improved process efficiencies through the use of cheaper hels and reductants, the high rate of metal recovery and the flexibility inherent in the technology to process various feed material types. The economical, process and environmental benefits of its application are highlighted for both the smelting and converting stages of copper production.

Jan 1, 1997

By B. Manana

In heap leaching, the oxidative dissolution of value minerals encapsulated deep within large particles cannot be fully understood on the basis of the bulk solution conditions relative to variable solution conditions near the mineral surface. In the present study, the diffusion of the oxidising species through inner particle pores is simulated in a model apparatus that separates an inert platinum electrode under controlled reduction potential from the bulk solution through narrow pores of varying length. The Cu-NH3 system was selected as a model system and Cu(II)/Cu (I) as the redox couple of interest. Platinum probes inserted in the pores allowed the measurement of varying redox potentials along the pore length. Results showed that in a 10 mm pore, there exists a narrow (0.5 mm) zone near the reduction surface that is depleted of the oxidant and in which its supply is strongly diffusion limited, even if it is in abundance in the bulk solution. The consistent presence of this narrow diffusion region across all experimental results indicated that the transportation of the reduced species away from the reaction surface had the most significant influence on the potential variations within the pore. This was further supported by the minimal effect of varying concentrations of both Cu(II) and dissolved oxygen on the solution potential within this region.

By Lauri Pajunen

DSA-anodes are widely used in metal electrowinning. In zinc electrowinning the electrolyte solution contains manganese ions, and the deposition of manganese dioxide happens on the anode. This manganese dioxide layer cannot be removed without losing the active coating of the DSA-anode. The same problem can be found with hybrid anodes. In hybrid anodes mixed metal oxide coated titanium mesh is attached to a lead base material. In this study, the effect of dissolved manganese on anode behaviour is studied with three different anodes. These anodes are lead anode with 0.6% silver, hybrid anode and DSA-mesh. Methods of study include polarization, galvanostatic and potential mapping experiments.

Jan 1, 2003

By Jian Pan, Deqing Zhu, Benjing Shi, Yuxiao Xue

COREX smelting reduction process which is freed of metallurgical coke provides a sustainable developing way for ironmaking industry. However, the shortage and high cost of pellets limit its development in China. Meanwhile, iron ore sinter has a great output in China. This work studied the reduction behaviors of sinter made from magnetite concentrates during the reducing process of COREX shaft furnace and compared the RI and RDI of sinter with BF process. The results showed that the reduction degree of sinter increased obviously during the temperature zone from 600 to 850 °C, while the reduction degradation presented rapidly aggravate in the temperature zone from 425 to 550 °C in COREX shaft furnace, and the increase of metallic iron content leads to the degradation of sinter got decreased slightly during the stage of temperature above 650 °C. Sinter got higher RI than BFprocess but also got higher RDI in low reduction temperature of 550 °C, which means sinter would have heavier disintegration in COREX shaft furnace.

Mar 1, 2017

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Haibin Wang, Kaile Tang, Chenn Q. Zhou, Guangwu Tang, Zhixiang Cui, Ping Zhou, Armin K. Silaen, Hongjie Yan, Zhi Wang

Bath smelting technology, such as the submerged lance smelting furnace, is used in the modern copper making industry. The first submerged lance smelting furnace developed by Dongying Fangyuan Nonferrous Metals Co., Ltd has shown potential for high productivity and energy savings. In this study, computational fluid dynamics (CFD) was applied to investigate the current design of the furnace. A three-dimensional multiphase CFD model was developed to study the interaction between injected gas and the liquid bath. The multiphase Eulerian model was used for simulating gas/liquid two-phase flow. The flow pattern in the submerged lance smelting furnace indicated rapid flow development and strong turbulent interactions between the gas and liquid phases. The model was validated based on a water model experiment of the mixing process. Mixing times from the simulation results show good agreement with experimental data. Additionally, based on this model, the gas residence time and liquid copper matte splashing phenomena under varying gas flow rates were investigated.

Mar 1, 2017

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By D. Holdridge, D. Liao, S. Waterfall, N. Strobl, S. Sun

High melting point inclusions, such as spinel, alumina and AlO rich calcium-aluminates, have a strong tendency to agglomerate on the tundish stopper rod and Submerged Entry Nozzle (SEN) during the steel casting process, and eventually to cause SEN clogging. Calcium treatmen by wire injection during steel refining during Ladle Metallurgy (LM) is commonly used to modify these troublesome inclusions to lower melting point inclusions. However, too much Ca injection (Ca over-treatment) can cause operational issue (e.g. slide gate plate erosion),as well as increase Ca cost. Therefore, it is desirable to add an appropriate amount of Ca to avoid either under-or over-treatment. Based on inclusion analysis with an ASPEX® computer controlled scanning electron microscope (ASPEX) instrument, AlO and AlO rich calcium-aluminates were identified as a major cause of SEN clogging at ArcelorMittal Dofasco Electric Arc Furnace (EAF) steelmaking stream. A Ca treatment index was developed to improve the inclusion modification. The improved inclusion control has reduced SEN clogging and enhanced steel quality.

Mar 1, 2017

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Sinter is an important iron-bearing material charged into blast furnace. Calcium ferrite (CF) is one of the most significant liquid phases in fluxed sinter. The isothermal reduction kinetics of CF and CF8M (n(CaO):n(Fe2O3) = 1, wt%(MgO) = 8) with 30% CO and 70% N2 gas mixtures at 1123, 1173, and 1223 K were investigated through thermogravimetric analysis in this study. Rate analysis illuminates that the reduction processes of CF and CF8M are mainly expressed as a typical two-stage reaction. Sharp analysis indicates that CF and CF8M reduction is expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction. The apparent activation energy values of CF and CF8M reduction are 46.9 and 31.8 kJ mol−1 individually based on model-free method.

Mar 1, 2018

By Hsi-keng Hu

"This paper deals with the flotability of stibnite and summarizes the major experiences and technological innovations of some typical practices of antimony sulfide ores in China. Experiences of cyanide-free and -less flotation of complex antimony sulfide ores and the application of the heavy media process to the preconcentration are described.Performance improvements obtained by innovations in operating techniques are also outlined and discussed. Technical innovations involve: (1) ramification roughing and differential-rate cleaning of stibnite-arsanopyrite ore; (2) the application of the new flotation reagent system; (3) process of separation flotation of Sb-Hg bulk concentrate; (4) extraction of gold from Au-Sb bulk concentrate; (5) flotation recovery of coarse stibnite particles.IntroductionChina is rich in natural resources of antimony and is one of the major antimony producers in the world. During the past several decades, a lot of research works have been done and many experiences in milling practices were gained, some of which are summarized briefly as follows.I. Heavy Media separation of Antimony sulfide Ore at Xikuangshan Hill, Hunan province (1)HMS as a technique of preconcentration of antimony ore has been performed more than ten years in China with good results.1. Ore characteristics The antimony ore of Xikuangshan belongs to the epithermal- metasomatic-filled doposit of antimony sulfide. Major minerals are stibnite (92.1%), antimony oxides (7.9%) and a small amount of pyrite and pyrrhotite; the gangue minerals are quartz, silicic limestone, calcite, hydrous kaolin, sericite, barite and others. The specific gravity of the ore is 2.8 and the specific gravity of stibnite and gangue are 4.6 and 2.654, respectively."

Jan 1, 1988

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004