Search Documents

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By Hoskings R

Conceptual studies of the run of mine stockpiling and reclaiming requirements com- menced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and com- pared with the alternatives. Foundations were designed to minimise clean up effort and to ensure stability of equipment under design wind loading without storm bays. Program- mable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By J Dwyer, G Turner, D Pridmore, M Urosevic

Due to their ability to produce high-resolution images of the subsurface to great depths, seismic surveys provide critical inputs to almost all oil and gas exploration projects. However, with some notable exceptions, seismic surveys have rarely been used in mineral exploration. In the past, this was due to both technical and financial reasons. Significant developments on both fronts mean that seismic surveys can now offer substantial benefits to mineral exploration and mining, and surveys conducted for exploration can provide important data sets for mine planning over the life of a mining project.We present case history data that show that seismic surveys can greatly assist with mapping the 3D distribution of lithologies and alteration and, in favourable circumstances, directly detect mineralisation in and around mineral systems. As a result of their high spatial sampling density, seismic surveys are also highly effective at mapping structures that can remain undetected or poorly characterised by drilling alone. These structures may host or provide important vectors to mineralisation. They can also be particularly important when planning shafts, raise bores, declines, stopes and open pit walls. A further benefit of seismic surveys is that they can remotely provide information on geotechnical rock parameters that are used for rippability, slope stability, blasting and ground support.CITATION:Turner, G, Urosevic, M, Pridmore, D and Dwyer, J, 2015. Exploration and mining unified through seismic imaging, in Proceedings Third International Future Mining Conference, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By A Dal-Corobbo

Traditional acid and metalliferous drainage (AMD) wastewater treatment focuses on the iron co-precipitation/adsorption process as this is a very effective method of reducing heavy metals, including copper, lead, zinc, arsenic, etc, to parts per billion (ppb) levels in AMD wastewater streams. One of the drawbacks to this method however is the large volume of sludge produced and subsequent disposal costs for the mine site concerned.A proprietary metals treatment system called high density sludge (denoted HDS) which significantly reduces the quantity of waste generated is described in this paper. This process generates a dewatered sludge that contains in the order of 50 to 55 per cent solids. This sludge is denser than conventionally dewatered sludge, which typically contains only 20 to 30 per cent solids. This advanced process has a wide range of applications and can be easily retrofitted into existing AMD treatment systems. It has been successfully installed at several mine sites to treat AMD wastewaters. This paper discusses the high density sludge process, its benefits and provides data and operating results from pilot test installations.CITATION:Dal-Corobbo, A, 2013. High-density sludge process for treating metal bearing acid and metalliferous drainage wastewaters, in Proceedings Water in Mining 2013 , pp 217-220 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Player, P Mikula, G Sweby

A numerical modelling back-analysis exercise was carried out at a WA gold mine at which early signs of seismicity (rock noise, scatts from active faces) were becoming apparent as depth of mining increased towards the 500 m mark. Some strain bursting had occurred and it was necessary to discover what the implications of this were for greater depth. The aim of the modelling was to: 1. Establish a correlation between observed ground conditions and model predicted damage, in overstressed areas of the mine. 2. Use this correlation to forecast rock mass damage and ground control requirements for proposed future stoping panels at greater depth. Good correlation has been achieved between observed rock mass damage, and a 3D Finite-Element RS3 model, run in elastic mode. Two candidate stress field orientations were modelled. The model parameter best fitting the observations was the Strength Factor (SF), the ratio of strength/stress. The good match (correlation coefficient of 0.7) between observed and modelled suggests that the elastic approach is justified for the depth range and rock mass properties analysed. The correlation also enabled a link between observed damage and installed ground support performance. Using the linear best-fit between observed and modelled, a forecasting exercise was carried out using the same RS3 model, modified to include future stoping. The resulting damage and ground support categories were obtained from the modelled SF for each proposed stoping level. Also, a series of generic geometries was assessed to investigate the impact of varying stope face lead/lag distance, sill pillar height and stope pillar size, on ground conditions. The key finding of the generic geometries were: • Ground support schemes have been defined for the expected conditions. • All ore drives are expected to have significant damage in the backs and rehabilitation. • Lead/lag distance not to exceed 10 m. • Sill pillar/level intervals of less than 20 m require an increase in ground support scheme. • Pillar sizes for maintaining footwall and hanging wall stability should be at least 10 m × 5 m.

Nov 29, 2022

By T Gill, A Faragher, B Scott, V Kakebeeke

In 2000, after six year intensive exploration for high-grade haematite deposits, Rio Tinto included the channel iron deposits (CID) as a specific iron ore target in the Hamersley Province iron ore exploration program. The exploration model was simple and based on the then current understanding of CID genesis. Fundamental to the model was an interpretation that CID deposits after their final accumulation stage could be entirely concealed in their channels. Inversion to mesas and therefore exposure of the CID profile would only occur in areas where the modern drainages follow the ancient and have significantly incised their current bedrock. The model took encouragement from observations at Bungaroo Creek, where large CID accumulations occur in a deep valley incised in the Wittenoom Formation concealed below recent valley fills derived from the surrounding BIFs. Also, in the headwaters of the Yandicoogina system CID occurs below a more recent cover of calcrete and clay. After a number of failed or partially successful attempts, exploratory drilling in 2002 in the Caliwingina valley in the northern Hamersley Range identified significant CID mineralisation. Subsequent drilling programs from 2003 onwards revealed the presence of a large CID system, which stretches from the middle reaches of the Caliwingina Creek to deep under the sediments of the Fortescue Valley, a channel length of more than 30 km. Although the drilling is still somewhat sparse, the geological resource estimation suggests that Caliwingina is presently the third biggest CID system of the Pilbara (after Yandicoogina and Bungaroo Creek) and is of comparable size to the premining Robe River system (1.6 Bt), with comparable Fe-grades to the Yandicoogina global resource grade (57.7 per cent Fe). Large detrital and canga deposits overlie the Caliwingina CID, or interfinger with it, and although the economics of these are presently unfavorable, could ultimately present a low-grade iron resource of slightly smaller size to the CID mineralisation at Caliwingina Creek. Together with the recently discovered Serenity and Solomon deposits, as well as Cabbage Gum Bore and other smaller occurrences, the Caliwingina Creek deposit is part of a major new CID district in the central Hamersley Ranges, approximately halfway between Yandicoogina and Robe River. Although exploration in this new district is still underway, the preliminary indications are that this area will provide a total CID resource well over 3 Bt, and is on a par with the major known CID systems in the Hamersley Province.

Jan 1, 2009

The building is a lofty, well-ventilated one of hardwood frame, with galvanized-iron walls and roof, and consists of five spans running north and south, covering a total length of 236 ft. Each span is composed of nine bays of 1:3-ft. centres, making the total width of the building 117 ft. The refinery is situated conveniently at a distance of 100 yds from the smelters. Through the third span of the building runs a 5-ton electric overhead travelling crane, of a 3-motor type, with a span of 29 ft. The crane runway extends over a railway line, which connects the smelters to the refinery. This crane is llsed for handling bullion, coal, melting kettles, lead pumps, &c. A 3-ton crane of similar type, but with a 50-ft. span, runs through the fifth span of the building and also extends over the railwav line alreadv mentioned. This crane is used to load the soft lead into railway trucks, or to stack lead awaiting shipment in the area covered by the crane's operations.

Jan 1, 1918

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By H R. Watling, W van Bronswijk

Of the various copper sulfides in the EarthÆs crust, chalcopyrite is by far the most common. This mineral is also the most difficult to leach, with hydrometallurgical extraction processes characterised by prohibitively slow kinetics. While a number of processes, including leaching at atmospheric pressure and temperature, pressure leaching at higher temperature, and bioleaching of concentrates in stirred tanks and whole ores in heaps have been demonstrated to some extent, there is currently no full-scale unit process for the hydrometallurgical extraction of copper from chalcopyrite ores. Titan Resources NL operated a test bacterial heap leach at Radio Hill, Western Australia in 2001, to extract nickel and copper from a mixed sulfide ore that contained significant amounts of chalcopyrite, pentlandite and pyrrhotite. A proprietary mixed bacterial culture was used to inoculate the heap, and the nickel and copper were precipitated from the resultant solution as mixed hydroxides. Although 65 per cent of the copper from the Radio Hill heap was eventually recovered, the rate of extraction followed an unexpected trend, as the initial rates of copper recovery were much slower than column tests had suggested. It was postulated that this was due to dissolved copper precipitating as covellite or chalcocite in the most poorly aerated zones within the heap, ie furthest from the aeration pipes at the base. It was further hypothesised that the lack of oxidants (oxygen, ferric iron) and the likely inactivity of bacteria in these areas limited the re-dissolution of such secondary copper precipitates. In this study the above hypothesis was tested in column experiments using the same mixed sulfide ore and a synthetic leach solution. One set of columns was aerated and another set was operated without aeration. Results showed that precipitation of copper occurred regardless of whether the column was aerated or not. The results suggested that pH of the leach solution played a significant part in the precipitation of the copper. Further column tests revealed this to be the case. These results are described here in detail.

Jan 1, 2004

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By S Kakara, A Kamaraj, S S. Varanasi, B V. R Mandalika, M B. Shaik

The properties of top slags play a very important role in secondary steelmaking. Fluxes should be chosen based on the ladle furnace (LF) slag requirements like viscosity, melting temperature, sulfide capacity, etc. CaF2 and CaO-Al2O3-based synthetic slags are the most used fluxes in secondary steelmaking to improve slag fluidity and interfacial chemical reactions. CaF2 is obsolete due to fluorine pollution and CaO-Al2O3 based slags have 40–50 wt per cent Al2O3 and 30–40 per cent CaO which is not beneficial for desulfurisation. Yet another drawback is that LF slag disintegrates into fine powder during cooling due to phase transformation C2S (2CaO.SiO2). Hence, there is a need for the development of low melting fluxes with high CaO content and the capability to prevent slag disintegration. The current work studied the effect of 0–9 wt per cent B2O3 on physico-chemical properties and characterisation of LF slags. X-ray diffraction (XRD) analyses were carried out to identify mineralogical phases present in slag and Fourier-transform infrared spectroscopy (FT-IR) analysis was done to understand the changes in bonds of B2O3 added LF slag. The characteristic temperature of slag was determined by a hemispherical method using high-temperature microscopy. Empirical models were used to calculate viscosity, break temperature, and sulfide capacity. FactSage™, ver 8.2 (by GTT-Technologies) simulations were carried out to find the equilibrium phase fractions and percentage of liquid slag at different temperatures. New phases such as Ca11B2Si4O22 and Ca2B3O5 were formed in LF slag with B2O3 addition. Based on the results, 0.5–1.0 wt per cent B2O3 was found to be sufficient to prevent C2S-driven disintegration of LF slag. Also, the melting temperature and viscosity of LF slag were reduced by adding 3–8 wt per cent B2O3 due to the formation of BO3 planar triangular structure and low melting eutectics in slag. Liquid slag started forming at a temperature as low as 800°C when B2O3 is >6 wt per cent. It was found that the sulfide capacity, viscosity, and break temperature of the slag decreased with increasing wt per cent B2O3. Based on the analysis carried out, B2O3 can be a promising fluxing material in secondary steelmaking, for improving the desulfurisation kinetics and valourisation potential of LF slag.

Aug 21, 2024

By A Simmons, J Chan, A Li, Q Gu, D M. Brett

The paper presents an example of field density achievements using thin layer deposition and solar drying and compares this with compaction data from laboratory testing and field trials of mechanical densification processes.

Jul 1, 2021

By E Lima, D Gregory, C Faria, A Lapworth

Open pit mine enterprises are complex systems that depend on multiple parameters such as mineral grade distribution, geotechnical characteristics, economic conditions and engineering requirements, all of which vary in time and space with a different degree of uncertainty. The unpredictable nature of these inputs imposes a risk to mine owners and shareholders which in the worst case can lead to highly undesirable financial outcomes.Desktop studies commonly examine a set of scenarios based on adjusting variables such as commodity prices, mining costs, processing costs, and metal recoveries to understand their relative impact on the economics of a project. It is less common to systematically explore and simulate hundreds of alternative physical designs to understand and compare the financial risk associated with one or more mining projects.This paper presents a risk assessment tool set and methodology that uses web based cloud computing to enable multiple simulations of mine designs to be rapidly and efficiently executed. The methodology includes generating random sets of prices and costs values within their respective probability distributions. Pit designs are then created to maximise the profit for each set of input variables. Various approaches to analysing the results are discussed. Use of the same high performance computing environment for understanding the financial risk associated with the variability of the underlying geological resource model is also discussed, with provided examples using case studies from two of the major mineral producers.CITATION:Lima, E, Gregory, D, Lapworth, A and Faria, C, 2014. Simulating extraction shapes to understand financial risk using high performance computing, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By P Craig, A Crosky, H Ramandi, S Saydam, H Chen

Frequency of reports on premature failure of rock bolts and cable bolts have increased in past two decades. Such a failure threatens both the safety of underground mine workers and the economic viability of the operations. Herein, we report on analysis of rock bolts and cable bolts failed recently in three underground mines in Australia. Magnetic particle inspection (MPI) and scanning electron microscope (SEM) techniques were used to study the failed bolts. MPI showed a number of subcritical cracks on the surface of the bolts. The majority of the cracks in both cable bolts and rock bolts were initiated from the base of ribs (indentation) where the stress concentration was high. SEM examinations showed tearing topography surface (TTS) in all failed rock bolts and cable bolts. These indicated that the failure occurred through hydrogen assisted stress corrosion cracking (HISCC). The results of this study enhanced the understanding about the failure of rock bolts and cable bolts in underground mines. CITATION:Chen, H, Ramandi, H, Craig, P, Crosky, A and Saydam, S, 2018. Analysis of premature failure of rock bolts and cable bolts failed in underground coal mines, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 407–413 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

By M Svartsjaern, D Saiang and K Mäkitaavola

The Kiirunavaara mine is a large-scale (28 Mt/a) iron ore mine located in northern Sweden. The mine is owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB) using sublevel caving (SLC). The SLC area underlies an open pit decommissioned in the 1950s, the current main SLC haulage level is situated at an depth of 1100 m. The main orebody dips 60 degrees to the east with a distinct boundary defining the hanging wall to the east and footwall to the west. Since the 1980s damage has been observed both in the footwall rock mass as well as on the footwall crest of the open pit. Recent investigations indicate that the underground footwall damage is primarily controlled by large-scale slope failure mechanisms. Structurally controlled near-vertical planar shear failures in the upper footwall appear to be driven or facilitated by a step-path like curved shear failure situated in a zone starting ca 250 m, and intersecting the SLC about 100 m above the active mining level. To confirm this failure evolution a pilot underground measuring system has been designed and installed to monitor the expected rock mass displacements indicated by numerical models based on the above mechanisms. The systems consists of 50 m time domain reflectometry (TDR) coaxial cables installed in the footwall both across and away from an estimated damage extent boundary to monitor shear movements along natural joint surfaces. The TDR installation is combined with long extensometers to facilitate differentiation between diffuse shear and rock mass normal expansion. Additionally, a low-tech system of tape extensometer lines are installed in drifts and stopes running perpendicular to the ore strike to monitor horizontal displacements in the infrastructure as the footwall ‘slope’ loses confinement during mining advance when the mined out areas are replaced by caved rock from the hanging wall.CITATION:Svartsjaern, M, Saiang, D and Mäkitaavola, K, 2016. Underground footwall monitoring at the sublevel caving mine – Kiirunavaara, Sweden, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 773–780 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Rayner, C Tsouris, A Komelkov

X-ray fluorescence (XRF) is a widely accepted technique for the elemental analysis of iron ores and their concentrates. Wavelength-dispersive, or WDXRF, and energy-dispersive, or EDXRF, spectrometers offer distinct advantages for particular applications, elements and concentration ranges and are, therefore, more complimentary than people might realise. A key example is the ability of EDXRF to identify, and often quantify, unexpected elements in production samples that would typically be missed by routine WDXRF. In this paper we discuss recent technological advances in XRF and present a novel application example that demonstrates the additional technical and practical benefits of using both EDXRF and WDXRF to characterise iron ores and concentrates.CITATION:Tsouris, C, Komelkov, A and Rayner, M, 2015. A novel approach to the characterisation of iron ores and concentrates using recent advancements in wavelength- and energy-dispersive x-ray fluorescence spectrometers, in Proceedings Iron Ore 2015, pp 591–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015