Search Documents

By Thomas C. Wilder

The activities of both components and the partial and integral molar thermodynamic properties of mixing for the liquid Al-Ge system at 1200°K and for the gertnanium-rich Al-Ge liquidus have been determined from data for eighteen alloys of compositions in the range 0.0593 < 0.880 using the reuersible gal-vanic. cell in the temperature interval 9320 to 1258°K. The liqui-dus compositions above 93 2 °K loere also ve determined by observing the discontinuities in the C us T plots for the high-melting alloys. This system shows moderate negative deviation from ideality throughout, the values for y° being 0.212 and 0.189 for aluminum and germanium, respectively, at 1200°K. Pavtial molar Properties of aluminum on the germanium-rich solidus and at infinite dilution in Ge(s) oboue 932°K were estimated from the foregozng measurements and the equlibrium data of previous investzgators. RECENT compilations of data1" have shown an increasing demand for knowledge of the thermodynamic properties of mixing of metallic alloy systems. In the case of binary-liquid systems where one of the components is a semiconductor this information is useful because, primarily, properties of the second (dopant) component on the liquidus, solidus, and at infinite dilution may be determined more accurately than from calculations based on the phase diagram. In this investigation a reversible galvanic cell was used to determine the chemical potential of aluminum in the two-phase region, liquid + [Ge], on the germanium-rich side of the A1-Ge system in the temperature range 932" to 1193°K. In addition, similar measurements for homogeneous liquid A1-Ge alloys for the entire composition range were obtained for the temperature interval 932" to 1258°K. The cell used was: The experimental technique and the treatment of the data were essentially the same as described earlier394 and are elaborated upon only briefly here. Each cell consisted of a liquid aluminum anode and three A1-Ge alloy cathodes of different composition which were held in Morganite alumina crucibles. The alloys were made up from aluminum and germanium weighed to the nearest 0.1 mg to a total weight of 5 to 10 g. Aluminum was a gift of Aluminum Co. of America and had a purity of 99.995+ pct. Germanium of transistor grade was a gift of Bell Telephone Laboratories. The four electrodes were contained in a larger alumina crucible which also held the prepurified fused chloride electrolyte. Contact to the electrodes was made by tantalum wire leads sheathed in alumina. The tantalum leads were centered in the electrodes by suitable positioning of an alumina radiation shield which fitted on the top of the - alulnina crucible. Two chrome l-alumel thermocouples, sheathed in quartz wells, completed the internal cell arrangement. The entire assembly was enclosed in an alumina tube, fitted with a water-cooled copper head so the system could be evacuated and then flushed with purified argon. *

Jan 1, 1967

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By Robert Lewis

THE Utah coal field to which the name Book Cliffs is applied runs in a northeast direction from Mt. Hilgarde, in Sevier county, along the escarpment of the Wasatch Plateau to the vicinity of Castle Gate, thence southeast along the Book cliffs, which lie to the north of and generally within sight of the Denver & Rio Grande Railroad,. to the Colorado line. The Book cliffs form the southern escarpment of the West and East Travaputs Plateaus, and vary in height from 2,000 to 6,000 ft. At the base of the Wasatch and Book Cliffs escarpments is a broad plain known as Castle valley. The coal beds outcropping in the escarpments along this valley are worked on the largest scale of any in the State, and this particular area is known locally as the Castle Valley coal field. Geology The Book cliffs are capped by the Tertiary-Eocene-formation, consisting of varicolored shales; buff sandstone, conglomerate, and subordinate thin beds of limestone. Different sections show diverse stratigraphy. This is mainly the Wasatch formation, and lies unconformably upon the rocks of the Upper Cretaceous. Fig. 1 is a generalized section of the rocks of the. Book Cliffs field. The Mesaverde formation contains the cliff-making rocks of the Book cliffs, and is composed of massive sandstone interbedded with sandy shales and beds of coal and carbonaceous shale. The sandstone has greater resistance to erosion and the formation is characterized by escarpment ledges and cliffs. The shale is commonly sandy and is drab in color, but where it is associated with the coal it is usually carbonaceous. The sandstone is generally buff, though occasionally it is white, and in places red. The bedding ranges from thin to massive. In the lower part. of the formation the sandstone is red in

Jan 7, 1914

By G. Howell Clevenger

FORMERLY great divergence of opinion existed in regard to the influence of copper in steel, as affecting its various physical properties. More recently the investigations of Stead,1 Breuil,2 Wigham,3 Burgess and Aston,4 Ball and Wingham,5 Miiller,6 Dillner,7 and others have shown fairly good agreement in the major points. Copper steel has been shown by these investigators to possess special properties which make it valuable for certain uses. The general range of composition of the useful alloys of copper and iron, and of copper, iron, and carbon, has been quite definitely established, for the former by Burgess and Aston,8 and for the latter by Breuil 9 and Stead.10 Stead 11 has removed one difficulty in reconciling certain of the earlier data by calling particular attention to the influence of carbon in copper steels. Another point which caused confusion in the earlier investigations, particularly in regard to " red-shortness," was the presence of sulphur. Failure to note the presence of sulphur often led to attributing " red-shortness " to the presence of small amounts of copper. Turner 12 has called attention to the fact that where copper exists in an iron ore it often occurs as the sulphide, so that the presence of copper in steel made from such ores might also, necessarily, mean the presence of sulphur. It is evident that the effect in this case might be quite different than where pure copper was added.

Jan 10, 1913

By G. L. Oldright, T. B. Brighton, C. M. Dice

The base bullion from the lead blast furnace contains varying amounts of the impurities left in the smelter feed by the concentrator, regardless of the method of smelter operation. These impurities may be held in part in mechanical suspension rather than being present as true alloys. However, usually there is little free space in the crucible in which to separate these drosses before the bullion is taken from the lead well. When such a dross is melted in a laboratory crucible and allowed to cool, the products obtained are lead bullion, speiss, and matte in well separated layers. Typical analyses of layers are: Analyses. Per Cent Element Bullion Speiss Matte Pb.............................................. 92.0 41.2 38.3 Cu.............................................. 2.4 36.3 40.6 As............................................... 4.0 16.5 4.3 Sb............................................... 0.7 0.2 0.4 S................................................ 0.6 1.9 13.1 Fe............................................... 0.0 0.0 0.0 Totals......................................... 99.7 96.1 96.7 The absence of iron in these products drossed from the blast-furnace bullion proves that the impurities for the greater part are not simply finely divided blast-furnace speiss or matte that has been dissolved or dispersed in the lead, but are held in solution by the liquid metal and rise to its surface as infusible compounds when the temperature of the bath is lowered. In general, the drosses made locally are metal sulphides and arsenides and not oxidized compounds. The large content of metallic lead also does not seem to be retained because of oxidized compounds

Jan 1, 1937

A SPRING meeting is to be held at Cleveland this month under the joint auspices of the Iron and Steel Committee and the Ohio Section with the cooperation of the neighboring sections in Pennsyl-vania, Illinois, and the other States of the Great Lakes region. The discussions will be focused on just one subject, that of manganese, but will cover that thor- oughly as is indicated by the following list of papers. TECHNICAL PROGRAM Some Political Aspects of the World Manganese Situa-tion. By C. K. Leith, Professor of Geology, Uni-versity of Wisconsin, Madison, Wis. Manganese Resources in Relation to Domestic Con-sumption. By J. V. W. Reynders, Consulting En-gineer, New York, N. Y. Manganese Deposits of the&apos; Gold Coast, Africa. By Sir Arthur E. Kitson, Director of the Geological Sur-vey of the Gold Coast, London; with Notes on the Petrology of Certain Associated Manganese Silicate-bearing Rocks. By Maj. N. R. Junner. Reserves of Lake Superior Manganiferous Iron Ores. By Carl Zapffe, Manager, iron ore properties, North-ern Pacific Railway Co., Brainerd, Minn. Iron Manganese Alloys Low in Carbon. By. Sir Robert Hadfield, Hadfields, Ltd., London. Manganese in Non-ferrous Alloys. By M. G. Corson, Consulting Engineer, New York, N. Y. Importance of Manganese in the Steel Industry. By H. M. Boylston, Professor of Metallurgy, Case School of Applied Science, Cleveland, Ohio. Minnesota Manganiferous Iron Ore in Relation to the Iron and Steel Industry. By T. L. Joseph, E. P. Barnett and C. E. Wood of the North Central Min-ing, Experiment Station, U. S. Bureau of Mines, Minneapolis, Minn. Representatives of the leading steel companies, the Army, the Navy, the Geological Survey, Bureau of Mines, and leading technical societies will be present and a lively discussion of the various papers is already assured. Nearly 14 pounds of manganese is needed for every ton of steel made. Estimates indicate that the total reserves of ore in this country suitable for making ferro would hardly supply domestic requirements for ten years, even if it could all be mined in that time. The grade of ore called for by present practice must come from abroad. The present tariff policy of this country is stated to cost industry $8,000,000 in order to force production of manganese ore to the extent of $600,000. What is the wise thing to do? Should a stock be accumulated? If so, how? Is it feasible to change practice and use low-grade ore or to beneficiate the ores of this grade and meet our requirements? What progress is being made in this direction? ,These and similar questions are raised in the various papers that have been submitted and will be open for dis-cussion.

Jan 3, 1927

By T. A. Rickard

The notion prevails that writing is a knack, that the skilful use of the pen is a gift of nature. This is an error. Dogberry may be responsible for it; he said: "To be a well-informed man is the gift of fortune, but to write and read comes by nature". Because Dogberry said it, we may be sure that Shakespeare thought otherwise. Ability of any sort may be partly innate, but my own observation and experience lead me to conclude that most of the easy writers have become so by constant practice. As I recall the names of men successful with the pen, I remember that most of them have written a great deal and have taken particular pains to improve their style. The suggestion that proficiency in the difficult art is a happy accident provokes a sardonic smile. The larger part of the great writing in our literature is the result of persistent effort. An easy fluency has been the undoing of many; their flamboyant and fantastic scribbling has proved as perishable as froth. This criticism applies to technical writing also; in order that a technical description or discussion may hold the interest of the reader, at least long enough to cause him to read it to the end, the writing must be done carefully and systematically; otherwise it will fail in its purpose of conveying information. Clearness is absolutely essential. "It is not enough to use language that may be understood; it is necessary to use language that must be understood."* The purpose of writing, at least of that which is meant to be read by others, is not only to express ideas but to communicate them. Lack of perspicuity may prove as %ad as

Jan 1, 1931

By Charles L. Mantell, Kurt Straler

The hydrogen reduction of Cr2O3 to chromium metal was found to be feasible at very low water-vapor concentrations, corresponding to dew points of -38° to -24°C, over a temperature range of 1130" to 1490°C. Hydrogen reduction under these conditions was predicted by the calculated equilibrium curves which also indicated that CrzOs is reduced directly to chromium without forming the intermediate oxide, CrO. This reduction path was confirmed by X-ray diffraction analysis. The percent reduction of Cr2O3 at each reaction temperature was constant with time, suggesting an inhibiting effect of water vapor. A small increase in the residual water-vapor concentration of a single temperature, 1490°C, strongly retarded the rate of reduction This effect was expressed by an empim&apos;cal equation which indicated a direct relationship between "distance from equilibrium" and the rate of reduction. me effect of temperature over the range of 1130" to 1490°C was expressed in an Arvhenius plot of log rate vs reciprocal absolute temperature. From this curve the apparent enthalpy of activation was found to be 29,600 cal. Based on the hypothesis that the rate of reductiun is contvolled at the oxide-metal interface, an over-all rate equation consistent with the experimental data and the thery of absolute reaction rates was formulated. A simplification of this expression to an Arrhenius equation was justified by the overriding effect of temperature on the rate of reaction for the minimum water-vapor concentration range. MOST of the metals in Subgroup V1 of the periodic table can be prepared commercially by direct reduction of their oxides by hydrogen or carbon monoxide, at temperatures considerably below the melting points of both the metals and their oxides. Chromium is an exception, being generally reduced from its ore, Cr2O3 . FeO, by silicon in an electric arc furnace which operates above the melting point of the Fe-Cr alloy or above the melting point of chro- mium if a chromium oxide be the starting material. In reduction of chromium oxide by hydrogen, either reduction does not occur at all or the rate of reduction is extremely slow. Theoretical considerations based on the high, exothermic, free energy of formation of Cr2O3 compared to the oxides of the other Subgroup VI metals, molybdenum, tungsten, and uranium, would also suggest a slow rate of reaction and a high activation energy. Interest in the direct gaseous reduction of fine-powdered ores in fluidized beds was considered justification for examination of this reaction. In order to develop a basis for a continuing study of the commercial feasibility of the direct gaseous reduction of chromite, a study of the kinetics of the reduction of Cr2O3 with hydrogen was undertaken. To the authors&apos; knowledge no accurate kinetic data for this reaction have been obtained. Neither has an activation energy been determined nor has an attempt been made to establish a mechanism of reaction. LITERATURE Maier10 compared the data of I. Y. Granaat,6 H. von Wartenburg and S. Aoyama, and G. Grube and M. Flad7 with that derived from calorimetric and ther-modynamic properties for the equilibria for the reduction of Cr2O3 with hydrogen. These results, plotted as the log of the equilibrium constant vs absolute temperature for the reduction of Cr2O3 and the intermediate oxide, CrO, to chromium, show agreement between the differently derived data. In both cases the equilibrium constants were extremely low. Maier showed that, over a temperature range of 1000° to 2000°K, Cr2O3 is more readily reducible than CrO. Granat assumed that CrO was preferentially formed from Cr2o3 above 1100°C. Grube and Flad&apos;s analysis of their reaction products in the 895" to 1000°C range indicated the coexistence of only Cr2O3 and chromium. The hydrogen reduction of the other Subgroup VI metals, molybdenum, tungsten, and uranium, shows that reduction of the higher oxide proceeds through all of the intermediate oxides before being reduced to the metal. Since evidence pointed to an anomaly in the reduction behavior of Cr2O3, the authors investigated the reduction path of Cr2Os.to chromium. This was done theoretically with more recently available free-energy data and experimentally by X-ray diffraction analysis. This work reinforces Maier&apos;s conclusion.

Jan 1, 1964

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. &apos; The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By J. H. Nead

The experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. Conclusions No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability. Composition of Materials An attempt was made to secure steels increasing in carbon by increments of 0.1 per cent. from 0.1 per cent. up to 0.8 per cent., and from that composition to 1.6 per cent. by increments of 0.2 per cent. Actually, however, steels of the composition given in Table I were procured, and as the carbon contents were arranged sufficiently well so that satisfactory curves could be drawn showing the relation between carbon content and other properties, these steels were used in the experiments.

Jan 1, 1916

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young&apos;s modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie&apos;s3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By H. A. Meyerhoff, R. J. Colony

Deposits of iron are widely scattered in the folded Cretaceous rocks and the associated igneous intrusives of Puerto Rico. Most of them are too small for commercial development, but a few have aroused some scientific and economic interest, among them the large body of residual limonite at the west end of the island near Mayagüezl-6 (Fig. 1) and the mixed hematite and magnetite deposit on the southern slopes of the Sierra de Cayey, about four miles north of Arroyo.7"9 Neither of these orebodies has been developed, nor have investigations of the widely distributed deposits of magnetite, which include all the remaining occurrences of iron deserving of economic consideration, proceeded beyond the exploratory stage. With the possible exception of the mixed deposit near Arroyo, the magnetite is directly associated with andesitic and dioritic intrusives, which invade the Cretaceous rock section, and the bulk of it, occurring in calcareous sediments, is clearly of contact-replacement origin. The small deposit on Rio Portugües, north of Ponce, is found in a limestone band near its contact with an andesite dike.10,11 Two deposits of unde-

Jan 1, 1935

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,&apos; and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Charles S. Barrett

This paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstruc-tures. About 1200 exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,&apos; and a number of these have been selected to illustrate the results obtained. prints are also included showing the common types of falsities—to borrow a term from the biological field, the "artifacts." ln brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. In addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains, since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. Specimen Preparation and Photographs Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for these polishing and etching (each successive polish becoming less severe and each etch lighter), since the fina1 etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and 16, the replicas used were of silica, deposited upon polystyrene and floated from the polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1944

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k&apos; where k&apos; is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By D. D. Homer, R. H. Cromwell

The Minas de Matahambre No. 2 shaft, vertical, four-compartment lined with steel sets and hardwood lagging, has been sunk 2057 ft. On account of rock structure, over-all cross-section dimensions are 23 by 6 ft. Certain sections have been concreted. Two compartments are for handling ore and men, one for supplies and men, and one for manway, cables and counterweight. Two 250-ton capacity skip pockets with air-operated gates and steel cartridge pockets have been installed underground. A steel "A" headframe, a 250-ton steel receiving bin, and skip-to-man-cage changing equipment have been provided. Skip capacity is 102½ cu. ft. The hoist is a Nordberg double-drum 10 ft. by 6 ft. 6 in. geared, electrically driven, with parallel grooving for 1-?in. cables. Maximum hoisting speed is 1600 ft. per minute. The motor-generator set, control panel, slip regulator and hoist accumulator are housed in the basement of the hoist house. The electrical equipment is General Electric. The direct-current hoist motor is 800 hp. Control is of the Ward-Leonard-Ilgner type. The motor-generator flywheel set, normal speed 720 r.p.m., consists of an 800-hp. induction motor, a 22-ton flywheel (dia. 117 in.) and a 650-kw. generator.

Jan 1, 1934

By E. A. Breitenbach

A computer program has been developed to afford rapid and complete quantitative log analysis for exploration and production decisions. The computation consists of automatic selection of tops and bottoms of porous intervals from the digitized data, and then point-by-point calculations within each selected interval. Nearly all log types can be analyzed. This paper presents the calculation techniques found to be appticable to machine evaluation and gives examples of their use. INTRODUCTION As the quantitative interpretation of well logs entails repetitive use of charts and equations, it is natural that digital computer programs would be written. A Universal Log Interpretation Computer Program (ULICP) has been developed to afiord rapid and complete analysis for exploration and production decisions. Application of this program enables the log analyst to: (I) apply rapid quantitative log analysis for exploration and production decisions on either a field, a well or on a single zone basis; (2) apply concepts of interpretation requiring detailed numerical analysis; (3) analyze all porous intervals on each log, rather than a few selected zones, and complete the analysis in less time than previously required. Computations are reported for every digitized point in each zone; (4) use empirical techniques applicable to a given area as an integral part of the computation; (5) experiment with the empirical coefficients and exponents in the interpretation equations to find the best possible solution; and (6) automatically plot both the original and computed data to scales analogous to the field prints. The primary utility of a log interpretation program stems from its ability to do an overwhelming amount of work with very little man-power. If a calculation procedure or thought process can be formalized to the extent that step-by-step logic can be written, a computer program can be developed that follows this logic. The major question is one of economics. A feasibility study of the costs for such a program indicates that digital processing is economical primarily as a means of increasing the productivity of the log analyst. In effect, the probability of missing productive intervals in any well, because of a lack of time to do detailed calculations, is greatly reduced. The nucleus of ULICP is programmed to compute large sections of a suite of logs by selecting zones automatically and then performing all pertinent computations on a data point by data point basis within each zone.&apos;.&apos; An entire suite of logs can be processed in this manner with very little manual intervention. Sufficient programming logic is available so that each log analyst can request computations pertinent to his area. These requests are made by simple additions or deletions of information on the input header cards. Hence, the log analyst is always in complete control of the computation process. The evaluation of a suite of logs requires pre-editing, digitization, computation, presentation of results and interpretation. Work by the log analyst is reqilired only in pre-editing and interpretation. Thus, he is allowed more time for comprehensive interpretation, rather than calculation. For continuity, the discussion of ULICP is organized sequentially: pre-editing, digitization, computation and presentation of results. DISCUSSION PRE-EDITING The extent of pre-editing prior to computation is dependent on the format of the original data. For analog prints, it requires inspection, correlation and editing of the logs, plus the entering of required data an special forms. For digitized data such as magnetic tape field recordings, only the special forms are necessary. The process for analog prints will be given here. The inspection and correlation process involves the selection of sections for digitization and the correlation of the traces to a common depth. To decrease the cost of digitization, traces that exhibit large variations in shale formations can be redrawn to a non-zero baseline. The next step is to enter all pertinent data on the input header cards. The header cards presently used for ULICP are presented as Figs. 1 through 6. Cards 1, 2, 3 and 4 (Fig. 1) are defined as the Main Header Cards. They describe the particular well for output identification and give basic information. Cards 5 through 15 (Figs. 2 through 6) are defined as the Block Header Cards. As such, they define the log types and the interpretation parameters for the block of data immediately following. Cards 1 through 10 are required for every computer run. Cards 11 through 14 pertain only to nuclear logs. Card 11 is required if any nuclear log is supplied, and cards 12 through 14 are required only when gamma-ray, density or neutron log data, respectively, are supplied. Card 15 (Fig. 6) must be supplied when cross-plot calculations are required. Either two- or three-component

Jan 1, 1967

By Robert Linton

Tats paper deals with work that has been carried on for over three years by the management and staff of the North Butte Mining Co. in an effort to standardize mining methods, to eliminate lost motion in the operating organization, and to improve the efficiency of the individual workman. Naturally, much of this work is an adaptation of ideas suggested by other mining operations or by practice in manufacturing and other productive industries. The studies, however, have developed some features that it is believed are new. Both new and adapted features are given in detail. The normal capacity of the North Butte mines is about 2000 tons per. day. Hoisting is done principally through the Granite Mountain shaft, which is 3740 ft. (1140 m.) deep and equipped with an electric hoist capable of hoisting 200 tons per hour from a depth of 4000 ft. (1219 m.). The lowest stoping level is the 3400-ft. The Granite Mountain shaft is connected with the Speculator shaft, about 850 ft. (259 m.) south, and with the Gem, about 1150 ft. (350 m.) east, which are 3000 (914.4 m.) and 2000 ft. (609.6 m.). deep, respectively. These two shafts are equipped with reversible fans for ventilation. The Speculator has a; steam hoist with a capacity of 150 tons per hour from the 3000-ft. level. The Granite Mountain shaft is concrete lined from the 1600-ft. to below the 3000-ft. level and gunited with cement from the 1600-ft. level to the surface. Sections of the Speculator shaft with a total combined length of 500 ft. (152.4 m.) are also concreted. There are approximately 36 miles (58 km.) of drifts and crosscuts in the mine, in which there are 15.2 miles (24.5 km.) of track. At normal capacity, about 75 stoping faces, 20 raises, and 30 sill development faces are working. Stoping is usually by the standard square-set method. Where the size of the oreshoot and character of. the walls permit, the rill (or cut-and-fill) system is employed.

Jan 8, 1920