Search Documents

By Sheng-ping He, Ya-bing Zhang, Qian Wang, Kun-peng Xu

A mass of Al2O3 tends to form during the continuous casting process of high manganese high aluminum steel, and the properties of mould flux and the quality of slab are seriously affected. The dissolution rate of Al2O3 into the CaO–SiO2–MgO–Al2O3–F−−Na2O−Li2O−BaO−B2O3 slag system has been investigated at 1573 K by employing rotating cylinder method. This paper focuses on the effect of Na2O, Li2O, B2O3, F−, Al2O3 contents and (CaO+BaO)/(Al2O3+SiO2) ratio on the dissolution rate. Experimental results show that the dissolution rate increases with increasing Na2O, Li2O, B2O3 contents and decreasing Al2O3 content, among which Li2O has the greatest effect on increasing dissolution rate; the dissolution rate increases with increasing F− content in slag A-1, but decreases with that in slag A-2; the dissolution rate increases with (CaO+BaO)/(Al2O3+SiO2) ratio within the range from 0.91 to 1.31. The dissolution rate of Al2O3 into molten flux is mainly affected by the viscosity of the molten flux and the thermodynamic driving force.

Mar 1, 2018

By Peiwei Hu, Min Lu, Tiejun Chen

Based on the analysis of properties of vanadium tailing (VT), the surface modification study was carried out as a polymer filler. The modification effects of the three kinds of coupling agents on VT and the mechanical properties of polypropylene (PP) composites with a modified vanadium tailing (MVT) were compared to determine the suitable surface modification agent and modification processes for VT. The results show that the best one is aluminate coupling agent DL-411. When the content is 1.2 wt% and the temperature was 100 °C, the activity index of modified vanadium tailing (MVT) is 95.53%. FTIR analysis shows that DL-411 has the strongest binding ability on VT. XRD analysis shows that VT has a heterogeneous nucleation on PP to induced b form formation, and DL-411 could enhance this nucleation. So the composites has higher strength and better toughness. When the content of MVT is 10 phr, the tensile strength, impact strength, flexural strength and flexural modulus of the composites are 47.51 MPa, 38.43 kJ/m2, 59.57 and 1654.36 MPa, respectively.

Mar 1, 2018

By Shiju Zhang, Yongnian Dai, Songli Liu, Wenhui Ma

The BaZrO3 and CaO-doped BaZrO3 ceramics were fabricated at 1750 °C for melting the Ti2Ni alloys, respectively. Employing XRD, OM and SEM, the influence of CaO on the composition of BaZrO3 and the interaction between the BaZrO3 ceramic and titanium alloy was investigated. The results showed that the CaO doped BaZrO3 was consisted of CaO and Ba 1−xCaxZrO3. The grain on the surface of BaZrO3 ceramic was loose after melting, and the thermodynamic analysis indicated that the dissolution-erosion was responsible for the interaction mechanism. An amount of BaZrO 3 refractory was attached to the Ti2Ni alloy bottom after the alloy was cooled. However, no refractory was found on the bottom of Ti2Ni alloy, which was cooled down on the CaO doped BaZrO3 ceramic. CaO additive can effectively reduce the interaction between the BaZrO3 refractory and the titanium melt, indicating that it was a very promising refractory for preparing the titanium alloy.

Mar 1, 2018

By Gen Kamimura, Hiroyuki Matsuura

Zinc is widely used for galvanization of steel plates due to its high corrosion resistance. Steel scraps containing waste zinc-coated steel plates are remelted for recycling of steel in electric arc furnace (EAF) process, in which zinc is concentrated in EAF dust ranging from 10 to 40 mass%. Therefore, recycling of zinc from EAF dust is important to secure zinc resource. Our group has proposed selective chlorination and evaporation method recovering zinc as a form of chloride from EAF dust. Since recovered zinc chloride may contain lead, iron and copper as impurities, purification of zinc chloride is essential for production of highly pure metallic zinc. In the present study, removal of lead chloride from molten zinc chloride-alkali chloride by cementation reaction adding zinc was investigated. Experimental results were analyzed and discussed thermodynamically and kinetically as well as the feasibility and limitation of this process were examined.

Mar 1, 2018

By Qingguo Xue, Jingsong Wang, Siyang Long, Jun Zhao, Haibin Zuo

In order to effectively use of low rank coal, the thermally dissolve coal (TDC) was extracted from four kinds of low-rank coals by N-2-methyl-2-purrolidinone (NMP) at high temperature and high pressure. The structures of thermally dissolve coal and residues were characterized by element analysis, FT-IR spectra. The effects of temperatures, coal rank, solid-liquid ratio and extraction time on the extraction yields of TDC were studied, respectively. Moreover, the extraction mechanism of TDC at mild conditions is proposed. The results show that the ash contents of TDCs from four raw coals are significantly lower than that of raw coals, and the volatile contents and H/C are significantly improved. For KL coal, with the increase of temperature, the extraction yield of KL-TDC is improved evidently from 33.75% to 56.25% and the ash content is decreased from 0.57% to 0.49% at 350 °C.

Mar 1, 2018

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

By Weida Guo, Sangsang Liao, Bart Blanpain, Muxing Guo, Qing Liu, Lingling Cao, Keshe Ren, Yannan Wang, Lefei Sun

The interaction between a supersonic oxygen jet and liquid metal is a dominant factor affecting transport phenomena during the converter process. A systematic description of the interaction is of significant importance for a quantitative understanding of the transport phenomena. In this paper, cold model experiments and the corresponding numerical simulations were carried out to investigate the gas-slag-metal interaction inside an 80 t BOF converter. The effects of the operation parameters, such as inlet pressure, slag thickness and slag viscosity on the multiphase interaction have been studied. It has been found that the cavity profile is closely related to the operational conditions. The cavity depth increases with an increase in oxygen inlet pressure, whereas the cavity width is much less affected. The cavity profile is also clearly influenced by the thickness of the slag layer. The influence of slag viscosity on cavity profile is not significant under the present simulation conditions.

Mar 1, 2018

By Shadia J. Ikhmayies

Zinc oxide (ZnO) flowered-fibrous micro/nanowebs were produced as thin films on glass substrates at 350 °C using the low cost spray pyrolysis (SP) method. The films were characterized using the XRD diffraction, scanning electron microscopy (SEM), and X-ray energy dispersive spectroscopy (EDS). Hexagonal structure was confirmed from X-ray diffractogram, which showed preferential orientation along the (002) line. SEM images showed two dimensional flowered-fibrous micro/nanowebs, and EDS elemental analysis revealed the presence of chlorine in the films in addition to zinc and oxygen. The obtained morphology is important for optoelectronic device industry and solar cells, where it provides large surface area that helps light harvesting.

Mar 1, 2018

By B. Manoj

Coal is a mineral and is extensively used as a solid fuel in developing nationsand hasa sizeable share inthe global fossil fuel reserve. Utilization of this resource generates excess spoil and large volume of low grade waste to the environment. In recent years there have been serious research on enhancing its value and exploring the utility of this carbonaceous material to novel carbon materials.

Mar 1, 2018

By Pier-Lorenzo Solari, Philippe Moisy, Michel Schlegel, Stephane Pellet-Rostaing, Eric Mendes, David Bengio, Richard Husar, Thomas Dumas

Ionic liquids (ILs) are molten salts composed of an organic cation that are liquid below 100 °C. They demonstrate unique physico-chemical properties such as good conductivity, negligible vapor pressure and non-flammability. As a consequence, they are often regarded as green solvents and could become an alternative to the use of both high-temperature molten salts and volatile organic solvents in rare-earth elements processing and recycling. The diversity of interactions existing in an ionic liquid allows the solubilization of both polar and apolar compounds. Moreover, coordinating functions on their composing ions can lead to stabilization of some species. For instance, in non-aqueous media, europium exists in the (II) oxidation state which is not stable in aqueous solutions. Understanding the mechanism of Eu(III) electrochemical reduction to Eu(II) and the stabilization of Eu(II) species in IL media could be of major interest for the development of innovative recycling processes. Using transient electrochemistry and UV-Vis spectroscopy we could get valuable information on the redox behavior of the Eu(III)/(II) couple in the ionic liquid 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([EMIm][NTf2]). Reduction of Eu(III) to Eu(II) and stability of Eu(II) was also studied thanks to a XAS-spectroelectrochemistry set up used to follow in situ the evolution of the XANES spectrum around the L3 edge of Eu during electrolysis.

Mar 1, 2018

By Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Fujita, Kohei Mitsuhashi

An investigation on improving copper and iron recovery by removal of organic carbon and carbonaceous gangue mineral through flotation was carried out. The ore contains chalcopyrite and bornite as valuable minerals, and dolomite and calcite as carbonaceous gangue minerals. The chemical composition of the ore indicates that grade of 2.08 and 5.37 mass% for copper and iron respectively, while carbon was 3.70 mass%. The total organic carbon in the feed was recorded as 2.02 mass%. The presence of these gangue minerals is detrimental to copper and iron recovery during flotation. Therefore a two stage flotation study was carried out to remove hydrophobic carbon and carbonaceous material from ore and to improve copper and iron recovery. The objective of the study was to find effective and selective flotation conditions which can eliminate gangue minerals from valuable minerals and improve quality (grade) and recovery of copper and iron. The obtained results could be used to develop a flotation circuit for recovering copper and iron from carbonaceous sulphide ores.

Mar 1, 2018

By Fuming Wang, Xi Chen, Shuai Liu, Changrong Li, Dan Wu, Yaxu Zheng

The effects of B content and austenitizing temperature on hardenability and toughness of Cr–Mo alloy steel have been studied. The results show that the hardenability is deteriorated with increasing B content and austenitizing temperature. With increasing temperature, more and more B containing particles were dissolved in austenite and increase the amount of B atoms segregating at grain boundaries. Moreover, the coarsening grains reduce area of grain boundaries and also increase the amount of B atoms at unit grain boundary, excessive B atoms segregating at grain boundaries promotes precipitation of M2B, which accelerates ferrite nucleation and reduces hardenability. The main elements in M2B phase are Fe, Cr, Mo and B. The B atoms segregating at grain boundaries during austenitizing promote precipitation of M2B during tempering which deteriorate toughness significantly.

Mar 1, 2018

By Jorge A. S. Tenorio, Pedro F. A. Prado, Denise C. R. Espinosa

There is an increasing challenge of waste management regarding the growth of photovoltaic (PV) technology. Often overlooked by its environmental benefits of greenhouse gas emission reduction, PV technology contain metals that are highly hazardous for the environment. Amorphous silicon (a-Si) PV modules employ indium-tin-oxide as transparent conductive oxide and given the high price of indium its recovery could be advantageous from an economic perspective as well. Leaching of indium was predicted by comparing the Pourbaix diagram with the values of oxidoreduction potential and pH measured on a phosphoric acid solution. The a-Si panel was subjected to thermal treatment to remove the proprietary, protective coating and allow leaching to occur. Then, indium could be leached by phosphoric acid in a jacketed reactor, reaching a concentration of 55 ppm (67% leaching rate) with a 0.2 g/mL of a-Si panel to aqueous solution ratio. The leaching of indium with phosphoric acid is novel and could open doors for many other recycling routes for solar panels.

Mar 1, 2018

By Mansoor Barati, Yindong Yang, Yonggang Wei, Bo Li, Alexander McLean

Reduction roasting followed by magnetic separation is an important method for treating laterite nickel ores. In this work, garnierite type laterite ore from Yunnan province in China was reduced by methane under different conditions followed by magnetic separation to obtain the ferronickel concentrate. The phase and microstructure transformations of garnierite in the reduction process were investigated using XRD and SEM-EDS. The experimental results showed that reduction temperature from 873 to 1173 K had only a small effect on content and recovery of nickel and iron. The content and recovery of nickel and iron in the concentrates increased slightly with prolonging reduction time. In addition, the nickel and iron content decreased with increasing methane concentration, but the recovery of nickel and iron increases. A decrease in the iron content and recovery were observed when the dosage of sodium sulfate varied from 5 to 20% at a temperature of 1073 K and reducing time of 90 min, while the nickel content and recovery gradually increased.

Mar 1, 2018

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The modification of structural clays by chemical processes is a common method. It usually uses strong inorganic acid attacks, aiming at improving the clay’s properties and applications. Among the applications are its use in clay-polymer nanocomposites, cosmetics, medicines, and bleaching clays. Tests using acid attack to modified Brazilian bentonites were successfully performed and, resulted in significant improvement in the clay properties. This paper discusses the use of a Brazilian bentonite modified by acid attack as bleaching clay. The treated bentonite samples were characterized by XRF, specific surface area (BET) and SEM/EDS. The treated clay exhibited improved bleaching capacity for Brazilian nut oil and other Amazonian oils.

Mar 1, 2018

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Sinter is an important iron-bearing material charged into blast furnace. Calcium ferrite (CF) is one of the most significant liquid phases in fluxed sinter. The isothermal reduction kinetics of CF and CF8M (n(CaO):n(Fe2O3) = 1, wt%(MgO) = 8) with 30% CO and 70% N2 gas mixtures at 1123, 1173, and 1223 K were investigated through thermogravimetric analysis in this study. Rate analysis illuminates that the reduction processes of CF and CF8M are mainly expressed as a typical two-stage reaction. Sharp analysis indicates that CF and CF8M reduction is expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction. The apparent activation energy values of CF and CF8M reduction are 46.9 and 31.8 kJ mol−1 individually based on model-free method.

Mar 1, 2018

By Yunqing Tian, Wenbin Huang, Weidong Zhang, Xiaopeng Wang, Gele Qing, Xiangjuan Duan

Pellet production requires iron ore concentrates have fine particle size, high specific surface area and good balling performance, so iron ore concentrates appropriate for pelletizing is limited compared to sintering. In order to extend the iron ore resources for pelletizing, the iron ore fines for sinter are studied in this paper.The effect of grinded iron ores o npelletizing, roasting and pellet quality were studied in this paper. The bond grinding index of iron ore fine is between 12.5 and 16.98 kwh/t. The grinded iron ore fine has good balling performance, the drop number and compressive strength of green pellet were improved with increase of grinded iron ore fine ratio. The compressive strength of roasted pellets were decreased with increase of grinded iron ore fine ratio, however it can be reached 2500 N.P −1 while proportioned with more than 80% of magnetite iron ore concentrate.

Mar 1, 2018

By Bowen Li, Canhua Li, Mingsheng He

Steelmaking slag is a by-product in considerable volume and a valuable material for various applications. In general, steelmaking slag is an alkaline compound of CaO, Fe2O3, and SiO2. However, its characteristics varies depending on the feedstocks, steelmaking process and cooling method of the slag. To utilize this by-product effectively, this study investigated the characteristics of steelmaking slags taken from Wuhan Iron & Steel Co. Ltd. The results showed that the slags mainly consist of the oxides of calcium, iron, and silicon, with low contents of magnesia, alumina, and manganese oxide with a feature of high alkalinity and lime saturation factor. The major mineral phases include belite, calcium ferrite, calcium hydroxide, wustite, quartz, and small amount of elite. Thermogravimetric analysis indicated the weight loss from ambient temperature to 800 °C is 8% in total. Melting test showed the glass transition temperature is between 1300 and 1350 °C, flow temperature is about 1400 °C. The slag samples investigated in this study can be considered as a typical glass-ceramic composite.

Mar 1, 2018

By Kristine Bruce Wanderley, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio

Magnesium is present in nickels leach liquor and it is often disposed in waste barriers. However, new technologies with the aim of recuperating magnesium and other metals in the liquor have proven that it is possible to reduce the amount of metal lost during nickel ore processing. In this context, high temperature crystallization removes magnesium, with a concentration of 8 g/L, as MgSO4 H2O from the leach liquor. Kinetic studies of this process are needed to evaluate the thermodynamics of the growth of crystals. Thus, this work aims to study the crystallization kinetics of MgSO4 H2O. Temperatures of 230, 210 and 200 °C were investigated in a batch crystallization system in solutions with pH2. Aliquots were taken at each hour up to 5 h of time residence and analysed by ion chromatography for magnesium concentration. The reaction mechanism as well as rate constant and activation energy for each reaction temperature were obtained

Mar 1, 2018

By Thomas Boundy, PATRICK TAYLOR

Indium recovery from liquid crystal display (LCD) waste has been the subject of over 50 peer reviewed publications over the last decade; however, the first commercial recycling facilities are just beginning to be built. The low value of indium in the LCD screen material has posed a major challenge to would-be recyclers. Uncommon material combinations and geometries have further challenged development. A review of published literature regarding extraction of indium from LCDs will be presented and themes of advantageous processes will be highlighted. Barriers to rapid expansion of any recycling technology in the form of manufacturin gpractices, environmental regulations, and geographic constraints will be discussed.

Mar 1, 2018