Search Documents

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified. The functions that have been maintained and transferred to other agencies are: ? Portions of USBM's Mineral Information and Analysis program formerly conducted in Washington, DC and Denver, CO were assigned to the US Geological Survey (USGS). ? The Mineral Land Assessment program in Alaska (Anchorage and Juneau) was transferred to the US Bureau of Land Management (BLM). ? The Health and Safety Research program in Pittsburgh, PA and Spokane, WA was reassigned on an interim basis to the US Department of Energy (DOE). In fiscal year 1997, it was permanently assigned to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is part of the Centers for Disease Control and Prevention within the US Department of Health and Human Services. ? Environmental Research at Pittsburgh, PA was assigned to DOE. ? Materials Research at Albany, OR was assigned to DOE. ? The helium program was assigned to BLM, where it will be managed pending privatization. ? Coal and noncoal mine maps were transferred to the Office of Surface Mining Reclamation and Enforcement (OSMRE). The following locations were closed: ? Research centers in Denver, CO; Minneapolis, MN; Reno, NV; Rolla, MO; Salt Lake City, UT and Tuscaloosa, AL. ? Field operations centers in Denver, CO and Spokane, WA. ? Washington, DC headquarters office. To provide a concise picture of all of the affected functions, the following is a synopsis of the USBM program functions and facilities immediately before the closure. There were two principal programs: information and analysis, and research.

Jan 1, 1997

By Th. Petropulos

The Zn-Ag-Pb mineralization zone near Molai (Greece) was explored by more, than 60 drillholes. Promising results led to the decision of additional drillholes in order to confirm the expected spatial extension of the deposit. A multiobjective approach is described which optimizes the location of a set of 5 additional drillholes. The decision is based on estimation errors for grade, thickness and depth of the main ore bearing layer, with respect to cut-off values for grade and thickness. The linear combination of these variables defines a favorability index which is used for mapping optimal drillhole locations. The map shows several clusters of favorable cells. A declustrering algorithm is used to select a representative cell for drilling in each cluster.

Jan 1, 1989

By T. Eggenberg

Mechanization and automation of logistic equipment has become one of the main key factors in raising productivity and competitiveness especially for complex and larger mining or tunneling projects. The Lake Mead Intake Tunnel #3 shaft mucking installation is a good example to demonstrate the potential that is found in an overall optimized logistic. It starts with the planning and results in using customized installations which fulfill the specifically defined requirements for the project. Rowa developed a solution and supplied a shaft mucking system using a discontinuous double drum hoisting concept with shaft buckets, loading, and unloading devices. With this fully automated system a continuous muck flow of 437t/h can be achieved.

Jan 1, 2010

By Andrew B. Allen, Charles W. Robinson, Robert L. Schneider

In April, the US Synthetic Fuels Corp. broke a three-year silence and made its first financial award by approving a $820,750 loan for the First Colony peat-to-methanol project in North Carolina (ME, May, page 403). Peat Methanol Associates (PMA), a partnership between Koppers Co., ETCO Methanol Inc., Transco, Peat Methanol Co., and l. B. Sunderland, broke ground at First Colony last year and plans to begin production in Dec. 1985. Although the award is only a small part of Synthetic Fuels Corp.'s $15-billion budget, it does signal the corporation's intention to move aggressively ahead. It also is a positive indication that First Colony will be completed and operated successfully. This article describes the methods and equipment that will be used to harvest peat at First Colony, as well as how the peat will be converted to methanol. Introduction Peat deposits found along North Carolina's coastal plain contain high-quality fuel-grade peat with an average heating value of more than 23.3 MJ/kg (10,000 Btu/lb) (dry), with a low sulfur and ash content. The deposits differ from other US peats in that they contain large, sound Atlantic White Cedar and Cypress logs, stumps, and roots that may extend throughout the full depth of the deposit. A second difference is that these deposits are much more highly decomposed and, in the raw state, have the appearance and feel of a heavy, reddish-brown grease. These factors make it impractical to use standard production equipment so a new line was developed. Also, because of these conditions, techniques were modified to facilitate production. First Colony Farms, located near Creswell, NC, developed and evaluated a milled peat program. Equipment for this production method was designed and built, production rates were established from field operations, drying rates were established, weather data were analyzed, and total operating and capital costs were estimated. The method depends on the sun and wind for drying peat to the desired moisture content, in this case around 40%. Therefore, field preparation is actually the construction of a large solar collector to dry the peat so it can be harvested and stockpiled. It is essential that this collector be properly profiled initially and maintained during production to prevent precipitation from ponding. Initial Field Preparation Initial field preparation includes cleaning existing canals and constructing ditches and water control structures for proper drainage of rainwater run-off, building adequate roads for site access, removing surface vegetation, and profiling and sloping the fields. At First Colony, the 60.7-km2 (15,000-acre) harvesting area was divided into 129.5-hm2 (320-acre) blocks about 1.6 km (1 mile) long and 805 m (0.5 mile) wide. This was accomplished by cleaning main outfall canals with adjacent roads built from canal spoil at 1.6-km (1-mile) intervals. Existing intermediate canals that feed into main outfall canals at 805-m (0.5-mile) intervals also are cleaned. Headland roads are constructed from canal spoil along each side of each intermediate canal. This 129.5-hm2 (320-acre) block is then divided into 32 harvest strips by small V-ditches constructed at 50-m (165-ft) intervals. At the end of the field with the lowest elevation, corrugated steel pipe culverts are installed under the headland road in each V-ditch to control rainwater runoff into intermediate canals. Runoff water from the fields is diverted to a holding pond to prevent any increase in peak water runoff rates and to allow for more uniform drainage rate than experienced to date. After the drainage system is installed, harvest strips are ready for grinding and sloping operations. Surface vegetation, made up of small, waxy-leafed shrubs such as Gallberry, Bayberry, Magnolia, and scattered pond pine, can be effectively ground and incorporated into the upper surface of the peat layer. Here, it will rapidly decompose and have little effect on overall peat quality, thus eliminating the standard practice of pushing the vegetation and upper wood layer into long windrows with bulldozers and hauling this debris from the fields. Incorporating vegetation into the upper surface is known as the initial 102-mm (4-in.) surface vegetation grind and is accomplished by using a modified Bros Rota Mixer. Following this operation, and by using the same unit, a sec¬ond grind with a depth of 200-255 mm (8-10 in.) is made. This reduces the debris to a finer consistency, mixes it with the upper peat layer, and grinds any wood found in the upper 200-255 mm (8-10 in.). After initial grinding operations are completed, the augering or sloping operations can be accomplished with little or no hin-

Jan 7, 1983

By Munson R. McKinney, Bryan A. Slim

To date some 1,000 exploration targets (by way of adits, mine dumps, shafts, outcrops and unstoped mine areas) have so far been identified using an interactive data base system to query a digital data base comprising topographic, cadastral geological and mine components developed as a compilation of old plans, records, surveys and recently flown aerial photography. The exploration targets are intended for early follow-up as part of a 1987 exploration programme to investigate the reserve potential of the former producing property located in southern Utah. Of further interest is the unscrambling of old mine plans to provide drill targets for investigation of unstoped reserves with one target being a possible 800,000 tons in part of the lower workings. The project site encompasses about 3,200 acres of mainly patented lode claims covering most of the claims and mines of the Gold Mountain mining district formed in 1889. Turn of the century mining saw several mines operating whose total production was at least 143,000 oz. gold and 460,000 oz. silver from steeply dipping veins up to 20 ft. or more in thickness.

Jan 1, 1987

By C. M. Jones

The training program developed at Sierrita over the last twelve months has led to several significant improvements in both safety performance and productivity. Our most easily quantified results have been in truck productivity, where we have also experienced a 6% decrease in truck cycle times. We feel this is due to increased skill levels and awareness on the part of our operators due to our new training effort. The cycle time improvement has resulted in an increase in Truck productivity of 6%. Costs associated with productivity training have been $160,300. This includes program development and execution costs, as well as lost productivity during the training itself. These costs are offset by $1,400,000 in savings directly attributable to the increased skill levels of our technicians due to our training effort. As such, this represents a solid, high return investment at Sierrita.

Jan 1, 1998

By A. D. S. Gillies

The provision of a suitable working environment in deep level mines requires the accurate prediction of the ventilation heat load. Mathematical models for predicting strata heat load have been under development since the 1930's and 1940's. Computer models for predicting this and other mine heat sources have been developed and refined over the last 20 years. Some empirical studies have occurred and there is an increased emphasis on the importance of underground studies. Any theoretically or empirically determined predictive method must of necessity make assumptions. Underground space with its irregular configurations and rough wall surfaces cannot be described by simple mathematical expressions. Some heat loads, such as machinery, may occur intermittently while others such as the influence of water evaporation are very difficult to quantify accurately. Current popular models for predicting mine heat load have been surveyed. In testing some of these it is often found that each estimates significantly different quantitative values for the expected load in a particular underground space under study. These differences are explained by the assumptions, simplifications and omissions implicit in each of these models. It would be easier to estimate conditions at any point if heat flow into mine air passageways could be described by simple equations with associated statistically-based confidence ranges. Use of probability distributions to indicate confidence ranges allows any heat level estimate to be expressed as a range of values with limits for maximum and minimum expected values. This approach allows many of the limitations of the popular predictive models to be overcome. A heat prediction method using this approach has been developed based on Monte Carlo simulation and tested on mine data from a number of operations. Heat flow levels which can be predicted by simple equations supported by probability distributions allow the engineer flexibility in adjusting a predictive model to the underground characteristics appropriate to the mine site under study. The influence of all heat sources present in the mine opening must be included. Prediction methods must be updated as mining systems and machinery change with time. Heat sources interact with one another and the system must therefore be understood in its entirety.

Jan 1, 1987

By Melvin W. Kraschnewski

In 1966 Central Ohio Coal Company and Bucyrus-Erie signed a contract authorizing Bucyrus-Erie Company to design and build a 220 cubic yard dragline. This dragline would be used for stripping overburden from their coal reserves located near Cumberland, Ohio. The size of the machine was arrived at after a thorough application study of their annual coal output requirement, depth of overburden and type of terrain. The design and construction of this machine which has been designated by BECO as model number 4250-W is the title of this paper. Size wise based on machine weight the 4250-W represents an increase factor of three over our largest current dragline. Probably the easiest way of presenting a machine of this size is to build it from the bottom up.

Jan 1, 1969

By M. A. Greenwood

The total value of coal, FOB mine, consumed in the United States was $21 billion in 1985. Roughly $6 billion was spent to transport coal from the mine to the consumer by rail. This indicates the impact railroad transportation has on the competitiveness of U.S. coal as an energy resource. Actually, this is just the tip of the iceberg. When you consider the largest U.S. reserve of coal, the Powder River Basin, which is possibly the lowest cost coal in the U.S., or maybe even the world, the transportation cost is the overriding factor in developing competitive pricing. Rail transportation costs from Powder River can be multiples of 2, 3, or even 4 times the cost of coal FOB mine. About sixty percent of all U.S. coal is shipped by rail. In the case of Powder River Basin coal and many other reserves there are no current alternatives to rail. Are there feasible alternatives to rail transport?

Jan 1, 1986

By J. Stowe

While there has been continual improvement in the models for predicating deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life. Tailings pipelines are increasingly operated at higher solids concentrations where there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar flow pipeline operation is possible as there are several operational laminar flow tailings pipelines. While our understanding of laminar flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines. New sensor technology has led to the development of an instrument that provides reliable indication of bed deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines. This paper provides an overview of the each of the above advances in the design and operation of tailings pipelines. OPERATING TAILINGS PIPELINES WITH A DEPOSIT Tailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit. Figure 1 shows a typical design duty envelope for a tailings delivery system as a function of solids throughput and solids concentration by mass. If the pipeline is designed to operate without a deposit at the lowest duty flow rate (4,480 m3/h), the operating velocity at the highest duty flow rate (6,590 m3/h) is about 1.5 times the deposition velocity. Considering that the pipeline wear and energy requirements are roughly proportional to the square of operating velocity, this results in an operationally inefficient system when the pipeline is operated close to the maximum design flow rate. Most systems tend to operate at maximum throughput after post-startup debottlenecking optimizations. Alternative Approach An alternate design approach is to ensure the pipeline operates without a deposit for the nominal flow rate and accept that a deposit will form when operating at lower flow rates. This results in the selection of a larger diameter pipeline, but there are significant benefits in terms of reduced energy requirements and lower pipeline wear.

Jan 1, 2019

By Nathaniel Arbiter, Brij M. Moudgil

Separating oil shale from waste material or into high- and low-grade fractions can have a major economic influence on the surface retorting process. Different shale rock components vary significantly in physical and surface chemical properties, such as specific gravity, color, and water wettability. Various techniques that use the differences in one or more of these properties have been proposed to preconcentrate oil shale before retorting. This article discusses some proposed techniques, such as gravity separation, sorting, and froth flotation. Retorting oil shale is the most common method for recovering oil from the rock. This process is accomplished either underground (in situ) or above ground (ex-situ or surface retorting). Both techniques have serious limitations, such as low recoveries in the underground method and the ability to process rich shales only in the above ground retorting method. Also, environmental problems are associated with both techniques. Some of these limitations could be overcome if feed to the retorts is of consistent grade. This could be achieved by selecting appropriate sites for in situ retorting and selective mining for surface oil shale retorting. Both of these, however, would have a serious economic impact on shale oil recovery. Obviously, little control can be exercised over preparing feed material in the in situ retorting process, but beneficiation of oil shale could definitely be advantageous in surface retorting, and should have positive influence on the overall economics of recovering oil from the shales. For example, preconcentration of mined shale could result not only in reduced costs for materials handling, but also in waste disposal costs, since waste characteristics before and after the retorting process are significantly different. Upgrading the oil shale might also allow substitution of alternate technology for retorting as well as extend the process to recover oil from marginal deposits. Also, the separated material may become a potential source for recovering other values from shale deposits. Overall, the incentives for preconcentration are to reduce costs and improve thermal efficiency of the recovery process. Oil Shale Properties Important to Preconcentration Oil shale is a carbonaceous rock assaying 5-30% organic material (kerogen) and 70-95% ash-forming minerals. Kerogen is soft, nonbrit¬tle or semi-brittle material, and generally forms a matrix between irregularly distributed mineral grains. Inorganic mineral mat¬ter-quartz, feldspar, dolomite, kaolinite, dawsonite, and nahco-

Jan 9, 1982

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By D. M. Conner

An innovative patented process has been developed to convert high volume wastes--fly ash from coal-fired power plants, municipal solid waste (MSW) ash from incineration, solids from waste water treatment and paper mill sludge into a high value and environmentally benign product in the form of a lightweight aggregate. Lightweight Aggregate is widely used in the building construction industry in the United States, Europe and some Asian countries. This paper will present the development of the process, the process itself and details on the first commercial scale plant. The commercial plant is owned and operated by Wisconsin Electric Power (WEPCO).

Jan 1, 1997

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By M. S. Walton

A conference attended by a limited number of invited participants was held last September in Denver under the auspices of the Underground Construction Research Council of ASCE funded by the National Science Foundation (RANN) to explore the problem of accelerating the transfer of advanced geophysical technology, used principally in the petroleum exploration industry, into more effective and widespread use in subsurface investigations for underground construction. There are technological problems, but technical difficulties and unfavorable ratios of benefits to costs are not the major obstacles. The problem centers on the complex way in which potential net benefits are translated into effective incentives to innovate for each actor in the complex web of individual, corporate and institutional entities involved in the planning, designing, building, funding, operation and ownership of major underground construction projects. The entities responsible for site investigation, design concepts and specifications do not directly bear the risks of unanticipated costs and failures, nor directly gain from savings. The conventional unit-price construction contract is strongly implicated in blocking innovation. Problems of risks and incentives, more than technical feasibility, must be solved before large investments in technical adaptation and adoption can occur.

Jan 1, 1974

By M. I. M. Darwish

In this paper, an effort was made to get more in-sight about the parameters that can affect air sparging technique optimization. Numerical simulations were used in predicting the effects of different parameters utilizing Shell?s in house MoRes simulator. The case of using air sparging to remediate source zone is considered in this work. Different air injection scenarios using continuous and pulsed air injection techniques, with different frequencies and durations, were compared. The amount of MTBE mass removed from the saturated zone and arrived to the ground surface, through the vadose zone, was the main criterion while comparing different air injection scenarios. The simulations results showed that pulsed air injection is better than continuous air injection in removing the MTBE and that the longer the OFF time is the better the MTBE removal.

Jan 1, 2008

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By S. Frimpong

The coal mining industry is an important sector of Canada?s economy. The cost of mining and haulage of coal in Western Canada is a major focal point when compared to inexpensive coal from Australia. Spot coal price volatility affect contractual price arrangements and this creates pressure on companies? profit margins and their competitive edge. In order to alleviate this pressure, companies may have to take short-term drastic measures that may hurt their strategic positions in the long-term. Companies must also create a mix of their products to ensure effective maintenance of profit margins given various quantity and quality constraints. In this paper the authors provide extensive analysis based on detailed probabilistic production systems for coal extraction and haulage in Western Canada. An optimization model is formulated for typical coal mining operations, processing and haulage from mine sites to the Vancouver Ports using linear programming algorithm. A stochastic model is also formulated to analyze the associated risks and uncertainties. These models are validated using data from five operating mines in Western Canada with varying quantity and quality products and uncertainties. The results show that the five mines studied have to produce between 180,000 and 2.10 million tonnes of metallurgical coal and between 70,000 and 2.16 million tonnes of thermal coal to enhance their profitability given the underlying constraints. The average expected probability of success associated with production capacities from these mines is about 66%. This results in a failure probability of 36%, which is extremely high under contractual arrangements. The results also show that management?s profit expectation of $83 million can be achieved at a zero percent failure probability. With a higher risk of failure of 10%, this expectation increases by 21% to $100.3 million.

Jan 1, 2011

Acid mine drainage (AMD) forms when sulfide minerals are exposed to oxidizing conditions in coal and metal mining, highway construction, and other large-scale excavations. Iron sulfides common in coal regions are predominately pyrite and marcasite (FeS2), but other metals may be complexed with sulfides forming chalcopyrite (CuFeS2), covellite (CuS), galena (PbS), and sphalerite (ZnS). Pyrite commonly occurs with these other metal sulfides thereby causing AMD where Cu, Pb, and Zn are mined. Upon exposure to water and oxygen, sulfide minerals oxidize to form acidic, sulfate-rich drainage. Metal concentrations in AMD depend on the type and quantity of sulfide minerals present. The drainage quality emanating from underground mines or backfills of surface mines is dependent on the acid-producing (sulfide) and alkaline (carbonate) minerals contained in the disturbed rock. In general, sulfide-rich and carbonate-poor materials produce acidic drainage. In contrast, alkaline-rich materials, even with significant sulfide concentrations, often produce alkaline conditions in water. Approximately 20,000 km of streams and rivers in the United States are degraded by AMD. About 90% of the AMD reaching streams originates in abandoned surface and deep mines. Since no company or individual claims responsibility for reclaiming abandoned mine lands (AML), no treatment of the AMD occurs and continual contamination of surface and groundwater resources results. The oxidation of iron disulfides and the generation of acidity occur through several reactions (Stumm and Morgan, 1970). The chemical equations can be found in Caruccio and Geidel (2000). If any of the processes represented by the equations were slowed or altogether stopped, the generation of AMD would also slow or cease. The equations show that 1000 Mg of rock containing 1% sulfur, all as pyrite, would yield upon complete reaction 31.25 Mg of acidity. Therefore, 31.25 Mg of 100% CaCO3 would be required to neutralize the acidity. The alkaline content of overburden determines whether there is enough neutralization potential (NP) to counteract the acid produced from pyrite oxidation. Of the many types of alkaline compounds present in rocks, only carbonates and clays occur in sufficient quantity to effectively neutalize AMD. A balance between the acid-producing potential and neutralizing capacity of an overburden sample will indicate the ultimate acidity or alkalinity that might be expected in the material upon complete weathering. Accurate prediction and control of AMD before surface mining require an understanding of three important factors: 1) overburden geochemistry, 2) method and precision of overburden handling and placement in the backfill during reclamation, and 3) the postmining hydrology of the site.

Jan 1, 2002