Search Documents

A method is proposed for the determination of antimony in ores. Antimony is volatilized as antimony iodide by heating with ammonium iodide at a controlled temperature.The fusion mixture is extracted with hydrochloric acid and the antimony content is measured by atomic absorption spectrophotometry using an air/ acetylene flame. The time taken for analysis when comparedwith existing fusion and separation procedures is considerably reduced. Cations and anions likely to be present in antimony ores were also studied for possible interference effects but were not found to interfere.

Jan 1, 1972

By Waldram JT

The Kelsey Centrifugal Jig incorpo- rates the principles of operation of a conventional mineral jig, at the same time utilising high centrifugal forces to extend concentration to very fine heavy minerals. The main operating variables which are adjusted to control processing of different types of material are centrifugal force, ragging material and size distribution. Pilot plant trials have been under- taken to examine concentration of a mineral sand in which the heavy mineral particles occur mainly in the minus 0.075 plus 0.032 mm size range. Stage recoveries of greater than 90% were achieved at concentration factors of up to 2, although lower recoveries were obtained with higher concentration factors. A final concentrate containing 65% heavy minerals was obtained.

Jan 1, 1986

A simple and rapid method for delennining gold and silver in carbon samples is described. The method involves dissolution of carbon ash in a strong oxidising medium of aqua regia and hydrofluoric acid. Gold and silver are determined in the resultant solution using atomic absorption speetrometry (AAS). The method is efficient and reproducible. Gold results are comparable to the standard fire assay results, with agreement of results within ± 5 per cent. The co-efficients of variation for gold and silver are 0.37 and 0.39 per cent respectively for six replicate analyses. The analysis of gold and silver in a batch of ten carbon samples can be completed in approximately four hours.

Jan 1, 1992

Opinions vary widely within the community on what are legitimate environmental social respon- sibilities. The extreme conservationists see the responsibility as the total preservation of the natural environment achieved by opposition to all forms of industrial development that would disturb it. The `growth-at-any-price men' consider it more important to stimulate economic growth, develop new industries, and maximize profit letting the environment take care of itself: within this wide spectrum of concern are the middle-of- the-road men, part of the vast majority, fully aware of the need to compromise to achieve a satisfactory economic growth rate whilst pre- serving to the greatest extent practicable the con- ditions upon which we depend for a balanced self-perpetuating existence. Environmental change is not new. It is the inevitable accompaniment of human activity. Plato wrote in the 5th Century B.C.* of the devastating changes wrought by man and his animals on the ancient world of the Mediter- ranean. Down through the ages rural development to *The Dialogues of Plato: `What are now her moun- tains were lofty, soil-clad hills; her so-called shingle plains of the present day were full of rich soil; and her mountains were heavily afforested-a fact of which there are still visible traces. There are moun- tains in Attica which can now keep nothing but bees, but which were clothed, not so very long ago, with fine trees producing timber suitable for roofing the largest buildings; and roofs hewn from the timber are still in existence. There were also many lofty cultivated trees, while the country produced bound- less pasture for cattle. The annual rainfall was not lost, as it is at present, through being allowed to flow over the denuded surface into the sea, but was received by the country, in all its abundance, into her bosom, where she stored it in her impervious potter's earth and so was able to discharge the drain- age of the heights into the hollows in the form of perennial springs and rivers throughout the land.' provide the necessities of life for expanding populations has required the destruction of vast areas of forest. Industrial activities over the last 200 years have discharged enormous quantities of solid wastes, liquid and gaseous effluents that were environmental pollutants of the worst kind. Urbanization has drawn people, their machines, and industries into vast concentrations aggregat- ing the environmentally bad effects of each to the extent that there is evidence that through thermal pollution these large urban industrial complexes nrp nffPrtina raainnnl rlimnta.c

Jan 1, 1978

The kinetics of chlorination of alumina and bauxite with CO/CI2 mixtures were studied in the range 300-1100°C. The temperature of prior calcination is critical in determining the reaction rates. An optimum chlorination temperature in the range 600°C-750°C was demonstrated such that there is no increase in reaction rates with increasing temperature. This lack of rate sensitivity to rising temperature is largely a function of the influence of gaseous diffusion gradients in the porous alumina together with a progressive decrease in surface area.

Jan 1, 1976

Iron and steelmaking slags have been utilised for a century. All dumps are now exhausted. Because of constraints in establishing new stock yards, all slags have to be utilised immediately. At present, this is being achieved. Only in a situation where there is an increase in pig iron and crude steel production, together with the impact of new residual materials competing from other industries can marketing problems be anticipated.

Jan 1, 1979

By Zieg GA

The Sheep Creek Project lies 30 km north of White Sulphur Springs in the Little Belt Mountains of central Montana. Homestake Mining Co. discovered base metal anomalous pyrite beds downdip from gossans in 1974. Cominco American began exploration in 1976, consolidated adjacent properties, and joint ventured with BHP-Utah International in 1985. High . grade Cu and Cu/Co mineralization intersected in a 1985 drill hole led to discovery of two separate deposits. The project area now covers over 175 km2 and is being actively explored for Cu, Co and Zn in a shale hosted bedded sulphide system.Proterozoic Belt Supergroup sediments host the Sullivan Pb/Zn deposit, stratabound Ag/Cu ores of the Revett Formation at Troy and Rock Creek, and base metal rich pyrite beds at Sheep Creek.

Jan 1, 1990

By Whiteley M, Robinson T, Vernon B

The Western Australian gold industry has approximately 100 operating plants, mainly CIP/CIL. The nature of the State's rapidly expanding gold industry gave rise to concerns over management of the cyanide hazard, in that most plants are remote from major population centres, have a workforce with a high turn over and use highly saline process water. Approximately 4,500 workers in the industry have the potential to be exposed to cyanide in the course of their normal work.This paper outlines the risk management strategy developed by Government and industry to monitor atmospheric HCN gas in the work environment and the role of continuing education and training along with regular site inspections by Department of Mines Inspectors.

Jan 1, 1990

Exploration by Cyprus Minerals Australia Company (formerly Amoco Minerals) has successfully outlined significant Au-(Cu) mineralisation at Starra, 150 kilometres south-east of Mt. Isa. Mineralisation is stratabound and localized in deformed and metamorphosed ironstones (B.I.F?) and iron-oxide bearing schists of the mid-Proterozoic Staveley Formation. Over 90% of the presently outlined potential ore occurs in 4 discrete zones within a strike length of 3.5 kilometres. The inferred geological resource in these zones is approximately 6 million tonnes grading 5 grams per tonne gold and 2% copper. Roughly half of this is open-pittable, but more rigidly applied mining criteria will probably reduce the exploitable tonnage. Detailed infill drilling is in progress and a pre-feasibility study has commenced. The joint venture partners, Cyprus Minerals (75%) and Elders Resources (25%) expect to make a development decision by the end of this year.

Jan 1, 1986

By B F. J Kelly

Multiple-point simulation is a family of methods used to generate conditional facies simulations that present the same spatial dependence as a user-defined training image. The main advantage of using a training image is the easy integration of geological concepts in numerical subsurface models. The strength of multiple-point methods is that it allows making the best use of geological expertise when data are too sparse for inferring a model of spatial continuity. However, despite being appealing to geologists, the multiple-point methods are often not used in practice due to the difficulty of building complex 3D training images that contain realistic features.A new framework for multiple-point simulation is presented that involves small and simple training images. The main idea is to use random transformations to expand the range of structures available in the simple training image. The training image is not regarded any more as a global conceptual geological model, but rather a basic structural element of the subsurface. Complex geological structures are obtained, whose spatial structure can be parameterised by adjusting the statistics of the random transformations, based on field data or geological context. In most cases, such parameterisation is possible by adjusting two numbers only. One advantage is that the training images are so simple that they can be easily built even in 3D. The method allows building 3D models that reproduce shapes corresponding to a desired prior geological concept and are in phase with different types of field observations, such as orientation, facies or geophysical measurements. The flexibility of the approach allows for naturally integrating different types of data. This is demonstrated on an example involving seismic data assimilation. Examples where complex 3D folded structures are built from a simple training image and a few orientation data are shown.

Sep 26, 2011

By Barnes E. L S

With the introduction of diesel powered loading and hauling equipment, a number of Australian mines producing less than one million tonnes per year from shallow orebodies have been dev- eloped by decline. This method of entry has the advantage of providing both flexible access and early prod uction. However, as the depth of mining increases so does the operating cost of haulage, due to the need for more trucks. This cost, together with increased capital requirements for both equipment and infrastructure, leads to the point where the alternat- ive of shaft hoisting must be con- sidered. With an established decline it is possible to provide an ore hoisting shaft using a drilled raise with subsequent stripping to a suitable size. Using DCF techniques and known equipment operating and capital costs, an economic comparison of the two systems is made to determine the limit- ing depth to which truck haulage can be used.

Jan 1, 1973

The current boom in the mining sector has required mining operations to ramp up production to meet the international demand for minerals. This increase in production is putting enormous pressure on on-site professionals, and in particular the role of the on-site geotechnical engineer is ballooning. Mining engineers are focused on machinery and schedules; geologists concentrate on grade control and resources; everything else becomes the responsibility of the geotechnical engineer. Day to day geotechnical engineering is very different from geotechnical design work, and a practical understanding of both is required to successfully carry out either role. In addition, a successful geotechnical engineer has to have a good understanding of almost all technical aspects of mining. Even more important are good communications skills and the ability to problem solve on the fly. None of these skills are taught at tertiary institutions and therefore need to be learnt in the workplace. However, the shortage of geotechnical professionals means that young engineers do not always receive the mentorship and training they need to develop confidence and technical effectiveness. This paper outlines the changing role of on-site geotechnical engineers and presents some thoughts on how industry and young engineers can adjust to the changes.

Jan 1, 2006

The paper deals with the problems of grouting methods for fissured-porous rock. The paper describes design procedure, injection process patterns and hydrodynamic testing techni- que to plan grouting programs for fissured-porous aquifers. A number of case histories is given to illustrate the imp- lementation of developed methodology at various mining pro- jects.

Jan 1, 1988

New Zealand China Clays operata a plant at Matauri Bay, Northland for the benefaction of hallosite clay. Production is several thousand tonnes per year of which about ten per cent per year is supplied to an expanding export market.

Jan 1, 1978

The treatment meIhods selected for the concentrator at Cobar Mines Pty. Ltd. called for a high degree of automatic control of both the grinding and flotation sections.The resulting concentrator layout includes a central control room overlooking both grinding and flotation sections. The control room houses process recorders, controllers, and indicators. together with motor stopstart stations and alarms.Plant instrumentation includes load cells and variable speed hydraulic drive feeders for feed-rate control of autogenous mills, together with nuclear density gauges, differential flow transmitters, and pneumatic control valves for water and pulp density control.Flotation cell pulp levels are controlled by floats and pneumatic actuators; flotation reagent controls include magnetic flowmeters and time-operated solenoid valves.

Jan 1, 1969

Modern, research-based approaches to mineral exploration are essential to the future maintenance of the mineral industry. These need to fully utilise the rapidly expanding growth of understanding of the evolution of the earth's crust, and be properly integrated with advances in understanding of chemical and physical processes involved in ore formation. BMR has a major role to play in supporting the growth and utilisation of this research base, as well as maintaining the national geological and geophysical bases which are essential both to tactical and strategic interests of Australia and of its mineral industry. The objective development of data-process modelling is one target of such strategic research based on a more integrated approach to research by BMR, mineral companies, CSIRO and the universities with emphasis given to promoting positive feedback during research activities. Examples of the success of strategic research in Australia and overseas are noted in the Text.

Jan 1, 1986

In another paper the author described the electrolytic preparation of highly-purified lead. One of the most difficult parts, yet perhaps the most essential part, of that research was to ensure, firstly, that the purification process should be effective; secondly, that it should remain effective; thirdly, that the lead should not be contaminated during the tests that were done on it. All this necessitated periodic analyses of the lead.The purpose of this paper is to describe the work done by the author to check the accuracy of some known rapid methods for the estimation of impurities in highly-purified lead, with the intention of applying them to the control of the electrolytic process above-mentioned.METHODS ALREADY IN USEThe literature sets out accurate methods for the estimation of impurities in lead, but these methods are both lengthy and expensive. For example, the method described by Hemingway is used in the Port Pirie laboratory of the Broken Hill Associated Smelters Pty. Ltd., but it requires a sample as large as 1000 grm., and the time required to analyse a sample extends over days, and is too long to allow of quick control over a running process. This method was used by the Associated Smelters to obtain the analyses quoted in another paper by the author.

Jan 1, 1932

By D Alexander

For nearly 100 years, the flotation plant metallurgist has often wondered what is happening æbeneath the frothÆ. To assist in unravelling this mystery, new technology has been developed as part of the Australian Mineral Industries Research Association (AMIRA) P9 project, to measure gas dispersion characteristics (such as gas hold-up, superficial gas velocity and bubble size) in industrial flotation cells. These measurements have been conducted in a large number of cells of different types and sizes by researchers from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. A large database has been developed and the contents of this database are described in this paper. Typical cell characterisation measurements show a wide spread in values, even in the same cell types and sizes performing similar duties. In conventional flotation cells, the typical gas hold-up values range from 3 - 20 per cent, bubble sizes range between 1 and 2 mm, and superficial gas velocity ranges from 1 to 2.5 cm/s. The ranges of cell characterisation measurements given in this paper will enable plant personnel to compare their operation to other similar types of operations from around Australia and the rest of the world, giving opportunities for further improvement to flotation plant operations.

Jan 1, 2005

By Jingmin Xin, Wenhua Xing, Zongxin Huo, Hongzhang Chen

Drawing up the successive plan for mining and development is a very important and regular plan work. The expert system of the successive plan for mining and development drawn up by computer is developed on the basis of network, computer simula

Jan 1, 1998

By B Ilich, M Brad, R Brandli, E MarT

The Wirtgen surface miner was investigated for application to the Cloud Break iron ore deposit since it can selectively mine thin seams and there is no requirement for drilling and blasting or primary crushing as the surface miner cuts and breaks the rock to secondary cone crusher feed size. A physical metallurgical study of the surface miner run-of-mine (ROM) from Cloud Break was conducted to better understand the product size distribution, amount of -31.5 +6.3 mm lump produced, lump stability and physical metallurgical quality compared to conventional drill and blast techniques. Since the Cloud Break mine was not in production, the lump product from crushing and screening of surface miner ROM was compared with product simulations using traditional premining physical metallurgical processing techniques including drop testing of PQ diamond core. Drop test conditioning is widely used in the iron ore industry to simulate blasting, crushing and screening at the mine and subsequent product degradation during handling from mine to port to predict both the amount of lump product on ship and the size distribution of the fines and lump. The size distributions of surface miner ROM for hard, medium and friable ore types show very tight size distributions with very little above 100 - 150 mm, about 60 per cent of the distribution between 75 and 6.3 mm, with less below 1 mm compared to conventional drill and blast ROM. Crushing, screening and drop test conditioning of the surface miner ROM produced more lump in equivalent ore types compared to drill and blast techniques or their breakage simulation using PQ diamond core. The higher lump yield from the surface miner was also confirmed by pilot scale crushing of some 7400 t of surface miner ROM from the Cloud Break trial pit. The lump produced from surface miner ROM was quite stable and showed similar low degradation characteristics to lump simulated from drill and blasting techniques. Product size distribution simulations using conditioned crushed lump from 1 m diameter Bauer hole samples were found to compare well with processed PQ core samples and surface miner product from trial mining at Cloud Break. The Bauer sample method is therefore considered to be a very useful close simulation to actual lump production, although the lump yield is lower.

Jan 1, 2007