Search Documents

By Collin Bartlett, H. Storch

"Modern metallurgical processes operating with oxygen enriched air, such as the Outotec Flash Smelter and Flash Converter, generate very concentrated SO2 off-gas, which in combination with Outotec sulphuric acid plant technology allows the production of high pressure steam to be used for power generation. Outotec combines well proven technology of sulphur burning plants for this purpose with metallurgical plants.The application of Outotec’s proven LURECTM process enables processing of SO2 gas of up to 25 vol.-%. This process maximizes the energy recovery from the SO2 oxidation at a suitable high temperature level which can be turned into high pressure steam. The application of the Outotec HEROSTM heat recovery system enables the generation of low pressure steam from the absorption energy released at the intermediate absorption step. Additionally, energy is also recovered in the acid coolers for boiler feedwater pre-heating.The concept of integration of high and low pressure steam in combination with the pressurized operation of the boiler feedwater deaerator, thus heating up the boiler feed water to temperatures around 160…170°C, enables indirect transfer of low pressure steam (for deaerator operation) into more valuable high pressure steam, which improves the degree of heat recovery. This is the characteristic of Outotec’s HEROS+TM process.The increased generation of high pressure steam will in turn enable the generation of more electricity when compared to a standard traditional sulphuric acid process."

Jan 1, 2014

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By C. Cekerevac

The paper addresses some geotechnical issues related to the construction of the Deriner dam and HEPP. Design considerations and rock stabilization measures are presented for the excavations which took place in a highly fractured and weathered rock mass prevailing on site. Particularly, the shallow excavations for the overflow spillways tunnels are discussed. These present huge openings that are 12 m wide and 18 m high in portal areas, with an overburden of approximately 20 m, for which numerical finite element analysis and structural discontinuity analysis have been performed to ensure safe excavation process and future operation.

May 1, 2009

By Anthony McDonald, Dominic Verhelst

"Hudson Bay Mining and Smelting Co. Ltd. (HBM&S) started up a zinc plant and smelter in late 1930, employing technology of that period. The zinc plant has since converted from a roast/leach operation to a two stage pressure leach operation to eliminate sulphur dioxide emissioms. The smelter, however, is still continuing with much of the original roaster/reverberatory furnace technology. This paper reviews the process flow of the copper smelter, with some comments on past and recent changes.Smelter FlowsheetPrior to July 1993, the HBM&S smelter operation consisted of seven areas, namely feed preparation, roasters, reverberatory furnace, converters, anode casting, fuming plant, and dust collection. A simplified smelter flowsheet is shown in Figure 1. The data for tonnage of materials moving through the circuit are presented in Tables I to 4, and are representative of the time period from July 1992 to June 1993. A change in the zinc plant technology in 1993 resulted in the elimination of a zinc-bearing sulphide leach residue from the smelter feed blend, thereby greatly reducing the zinc content of slag produced in the smelter. Consequently the fuming plant and ancillary equipment, such as the drying plant, were shut down. These areas will, however, be described. With the closure of the zinc fuming furnaces all the slag from the reverberatory furnace is now discarded to stockpile.The over-all smelter metal recoveries are 96% for Cu and rn.5010 for Au and Ag. Figures 2 and 4 indicate historical production numbers of copper, silver and gold, respectively. A review of the minor element distribution in the smelter can be found elsewhere."

Jan 1, 1994

By E. E. N. Smith

"Uranium exploration by Eldorado prospectors north of Lake Athabasca began in late 1944 and resulted in initial discoveries in 1946 in the Beaverlodge region with mill production starting in early 1953. The operation was closed in mid-1982 having produced 21,457,947 kilograms U30 8 from the Eldorado FayVerna mine, Eldorado satellite operations and from other district producers on a custom basis.The Fay- Verna mine consists of pitchblende-brannerite orebodies spatially associated with both sides of a regional eastwest structure, the St. Louis Fault. The orebodies in the footwall (Fay) are elongate deposits of two types raking steeply to the southwest along the 50 degree south dip of the fault.One type consists of networks of fractures and veins filled with pitchblende, calcite and quartz in chlorite, epidote-altered mylonitized mica schists and amphibolites of the Middle Aphebian Tazin Group. The other type is comprised of fragments of mylonitized metasomatic quartz-feldspar granite of Late Middle Aphebian age cemented with a matrix of pitchblende, brannerite, calcite and some quartz. The vein networks lie en echelon in the footwall of the breccia ore bodies which, in part, are capped by the mud gouge of the St. Louis Fault; in other places, the breccia orebodies are overlain by basal conglomerates, grits and arkoses of the late Aphebian Martin Formation which itself immediately underlies the plane of the fault.Orebodies in the hanging wall (Verna) are a series of irregular, tabular deposits lying within a tightly overturned syncline of Tazin mica schists, amphibolites and siliceous mylonites. They consist of pitchblende, calcite-filled fractures grouped into zones and deposits displaying stratabound habits within individual rock types.Also described are several Eldorado satellite properties which were significant producers of uranium and which display complementary geology to that in the Fay- Verna mine.In general, uranium deposits in the Eldorado Beaverlodge region are closely related to minor structures associated with major faults. Uranium appears to be best concentrated where the rocks are well mylonitized and brecciated. Pitchblende fills networks of veins and fractures in metasediments and metavolcanics as well as matrix material cementing brecciated, mylonitized granite. All deposits in the Beaverlodge region lie in close proximity to the unconformity between the Martin Formation and the underlying Tazin Group."

Jan 1, 1986

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By E. Yalçin, A. Ünal

In transitional mineralization, the sill of the underlying variogram is relatively easily estimated, but the estimation of the nugget effect may be more difficult. This study aims to determine for massive copper deposits just how sensitive the estimations of ore reserve, economic copper content, total net value, and ultimate pit limits are to the errors of estimation in the nugget effect of the spherical variogram model. A massive copper deposit which has a log-normal distribution and a spherical variogram was simulated on a rectangular grid using the turning bands method. By using the three dimensional random kriging method, the mean block grades were estimated at four different sampling densities. The ultimate pit-limits were determined by using the two-dimensional dynamic programming algorithm. To calculate the estimation errors, the values obtained by using the actual nugget effect and structured component values were deducted from the estimations obtained using the incorrect nugget effect and structured component values. For isotropic massive copper deposits, it was found that the ratio of the nugget effect to the structured component of the spherical variogram has no significant effect on either the block grades estimated by the kriging method or on the ultimate pit limits.

Jan 1, 1992

By E. Ghali, W. Zhang, C. Su, N. Sorour, G. Houlachi

"Zinc electrowinning process is sensitive to the presence of metallic impurities such as lead ions that could substantially and negatively affect the power consumption and surface morphology. Effect of various concentrations of manganese ions and traces of lead ions up to 2.5 mg L-1 added to the electrolyte during electrowinning have been investigated by electrochemical polarization techniques such as galvanostatic, cyclic voltammetry and potentiodynamic. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were applied to examine the surface morphology and crystallographic orientation, respectively. Microwave plasma-atomic emission spectrometry has been used to determine the lead content in the deposit and in the electrolyte after electrodeposition. It was found that lead ions added to the zinc electrolyte led to the increase of cathodic overpotential and current efficiencies of zinc deposit. However, addition of Mn2+ into the zinc electrolyte resulted in the decrease of cathodic potential and current efficiency of zinc deposit. It can be stated as example that galvanostatic polarisation at 40?C and 52.5 mA cm-2 in presence of lead up to 0.1-0.2 mg L-1 in the electrolyte and 8-12 g L-1 Mn could be better considered as practical working parameters for electrowinning process.INTRODUCTIONApproximately 85% of the global production of zinc metal is produced by electrolytic process (Sinclair, 2005). The main goal of the zinc plant is to obtain pure zinc deposits with high current efficiencies. Smooth and pure deposits with high current efficiency (CE) are always obtained from pure electrolytes (Alfantazi & Dreisinger, 2001). The presence of metallic impurities in the zinc sulphate electrolyte is a major problem for the zinc electrowinning industry, since decreases in current efficiency, changes in deposit morphology and cathodic polarization are observed for electrolytes containing small concentrations of impurities (Ault & Frazer, 1988; Muresan, Maurin, Oniciu & Gaga, 1996). Low level concentrations as parts per million of these impurities are reported to influence negatively the zinc electrodeposition (Beshore, Flori, Schade & O'Keefe, 1987)."

Jan 1, 2016

By V. Itkin

"Three methods were tested for the beneficiation of aluminum scrap, generated by heavy medium separation of non-ferrous automobile scrap residue. These were: crushing in a shredder followed by screening; grinding in a ball miff followed by screening; and eddy current separation. The best results were obtained with the grinding-screening method. IntroductionThe usual method of aluminum alloy reclamation from non-ferrous automobile scrap residue consists of a two-step heavy medium separation to remove materials lighter than and heavier than aluminum. The resulting aluminum scrap still contains over 15% impurities such as stones and glass, heavy rubber, insulated copper wire , plastics and heavy metals entrapped by macerated aluminum piece s, composite fragments, etc.(2). Upon melting, these impurities create difficulties and yield a low ingot recovery-65% to 70%, hence small foundries avoid this material.There are a number of ways to improve the quality of aluminum scrap such as:(1 ) crushing of the scrap, which powders the brittle content , a major impurity component, followed by screening out of the dust(2) eddy current separation , which removes metals from the material flow, and(3) implement better methods for density separation.The eddy current separation and two variants of the comminution-screening technique were studied by Intermetco Ltd., Hamilton , Ontario."

Jan 1, 1986

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By K. Reinharter, J. Schmidl, D. Gregurek, A. Spanring

Copper smelting furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear. This paper evaluates the common refractory wear mechanisms as observed in the copper Peirce-Smith converter and in the copper anode furnace. The chemical factors include corrosion caused by fayalite type slag and sulfur supply, as well as, by Cu-oxide attack. Changes in the temperature during the furnace operation (thermal-shock) create stresses in the brick lining which can only be absorbed in limited extent. Mechanical factors include erosion, caused primarily by the movement of the metal bath, slag and charging material, as well as, stresses in the brickwork due to punching. Finally improper lining procedures can also effect the service life. All these wear parameters lead to severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” together with thermochemical calculations by FactSageTM software is an important prerequisite for the refractory producer. Based on these research results, combined with specific process knowledge, appropriate brick lining solutions for copper processing furnaces can be recommended. INTRODUCTION The refining of copper includes converting of matte or black copper into blister copper for final fire refining process in the anode section. Typically Peirce-Smith (PS) converters are in use. Other technologies include Hoboken Converter, TBRC but also Flash Converting Furnace and bath smelting furnaces (ISA, Ausmelt) (Davenport et al., 2002). For fire refining two types of furnaces are used – the rotary furnace type is dominantly used in the primary production route while secondary smelters tend to use hearth refining furnaces which are more suitable for scrap melting. Installed working linings are based on magnesia-chromite bricks but especially in the anode refining section the application of alumina-chromia bricks have become more popular in the recent years. It comes without saying that, to some extent, large variations in the slag composition can be observed from the data provided to RHI Magnesita during post-mortem studies of used refractory samples and this needs to be addressed properly during the selection process of refractory linings.77

Jan 1, 2019

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By Yue hua Hu, Wei Sun, Pan Chen, Li Wang, Runqing Liu, Central South University

"The flotation separation of muscovite from quartz was investigated using mixed sodium oleate/dodecylamine (NaOL/DDA) collectors. The flotation experiments were conducted on single minerals and their collecting performances were studied by means of adsorption amounts and molecular dynamics simulation. Flotation results show that muscovite presents good floatability while quartz exhibits poor floatability in alkaline condition. Adsorption amounts show that both NaOL and DDA can absorb onto surfaces of muscovite and quartz in presence of mixed surfactants. Molecular dynamics simulation indicates that DDA plays an important role in the adsorption of mixed surfactants on these two mineral surfaces. The molecules of mixed NaOL/DDA are arranged in a rigid and well-ordered packing on muscovite (001) surface. Only a few DDA adsorb on quartz directly, and rest DDA and NaOL molecule exist near by the quartz surface, forming a hydrophilic cylinder-like structure. This study may provide guidance for the flotation mechanism and application of mixed anionic/cationic collectors.INTRODUCTIONIn the past decades, there has been an ever-increasing demand for muscovite (KAl2(Si3Al)O10(OH)2) because of its potential applications in cosmetics, construction and metallurgy industries (Barlow & Manning, 1999). Besides, muscovite is an important carrier for some rare metals, including vanadium, titanium and lithium (SsuerrN, 1979). Quartz (SiO2) occurs as the main gangue mineral in muscovite ores, which results in a low purity of muscovite and limits its wide applications. Therefore, there is an urgent need for the beneficiation of low grade muscovite ores. Many studies remove quartz by screening and gravity separation in virtue of their differences in shape, hardness and density. However, these methods undergo poor efficiency in case of small particle size (below 50µm) of muscovite and quartz (Liubakka, Sullivan, Lamphere, Corradi, & Dykhuis, 2011; Santos, Franca, & Ogasawara, 2011)."

Jan 1, 2016

By J. W. Matousek

"More copper concentrates are treated in flash smelting furnaces than by any other process, and such furnaces are located in most of the world's major copper producing areas. Except for perhaps two furnaces treating chalcocite-type materials, little difference is seen between the grades of the concentrates being smelted. Within individual smelters, even less variation in feed grades is found. This is both accidental and intended. Many furnaces treat concentrates from captive ores, and these tend to be of relatively constant composition over long periods. Toll smelting operations blend concentrates to ensure delivery of feeds of fixed compositions to their furnaces to avoid upset conditions. Matte grades vary between flash smelting furnaces, but most commonly, these are the result of differences in operating practices rather than because of differences in concentrate grades. This paper reviews an industrial flash smelting test in which the copper content of the furnace feed was intentionally altered over a wide range. IntroductionExcept in a few copper mining regions of the world, the principal copper mineral is chalcopyrite (CuFeSz). This results in the almost universal production of concentrates containing 25070 to 30% copper (and similar amounts of iron and sulphur). Many operators of copper flash furnaces spend their entire metallurgical careers smelting concentrates of essentially fixed grades. This is true both of smelters treating concentrates from captive mines and those processing concentrates on a toll basis. From the production staff's point-of-view, the less variation in grades seen by the furnace, the better. Fixed analyses of concentrates and constant feed rates produce consistent quantities of matte at a consistent grade for processing by the converters. The result is, even in smelters treating a variety of concentrates, efforts are expended in sampling and blending to ensure feeds of relatively uniform compositions being sent to the furnaces."

Jan 1, 1993

By M. C. Villeneuve, P. A. Siratovich

We present an integrated analysis of laboratory-based thermally induced fracturing and results of numerical models to give insight to the role of thermal shock fracture on geothermal reservoir rocks. Thermal stimulation is a reservoir permeability enhancement technique applied to commercial geothermal reservoir rocks to enhance fluid injection capabilities for spent power plant working fluids. The process is well known to enhance permeability but the thermodynamic and physical constraints of the process are less certain. In an attempt to constrain the interaction and the ideal conditions that lead to permeability enhancement, experimental procedures were carried out to mimic the conditions that a reservoir rock would experience during a thermal stimulation using temperature differentials ranging from 50-300°C. Samples underwent such thermal gradients under controlled laboratory conditions and were characterized for the changes to permeability, porosity, ultrasonic velocities, dynamic elastic moduli and petrological changes. The thermal stimulation was simulated in a FLAC2D thermal numerical model to investigate the nature of the thermally induced changes in the sample. The development of this model also allows us to investigate the relationship between geological characteristics and the ability to thermally stimulate any type of rock. The results indicate that numerical thermal shocking experiments are corroborated by laboratory-based results. The implication of this study is that the refined numerical models present an insight to the conditions and constraints under which thermal stimulation can prove to enhance permeability that could not be gained through purely laboratory-based studies.

Jan 1, 2015

By Stanley Davidson

Introduction The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oyster-shaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than fifty years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis. The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass which, however, is here concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling. The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proven to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the "Edison' shaft never reached bed-rock.

Jan 1, 1946

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946