Search Documents

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By J. F. Liu, L. Chen, C. P. Wang

"Calcite-cemented joints abound in the rock masses of Beishan area, which is the most potential area for the high-level radioactive waste (HLW) disposal of China. The mechanical properties of Beishan granite containing a calcite-cemented joint with a dip angle of 82° was investigated under uniaxial compression and the acoustic emission (AE) characteristics were also studied in this paper. Compared to intact granite, the calcite-cemented joint caused a decrease more than 50% in uniaxial compressive strength and a decrease more than 90% in shear strength. The Young’s modulus was also decreased, while the circumferential deformation of jointed granite was sharply increased. The AE monitoring system successfully recorded the process of micro-crack development and the results indicated that the risk of rock-burst could be reduced due to the appearance of calcite-cemented joint.INTRODUCTIONThe properties of jointed rocks differ considerably from that of intact rock. Due to the difficulties in specimen preparation, analogue experiments with artificially prefabricated fractures are often used to study the mechanical behavior of jointed rock (Chen et al. 2012; Kulatilake et al. 2001; Singh et al. 2001). However, natural joints are not quite similar to the artificial fractures and it is necessary to investigate the mechanical behavior of jointed rocks. Xie et al. 2011 studied the mechanical properties of marbles with natural joints by uniaxial compression tests and found that the uniaxial compressive strength of jointed rock is greatly decreased. With the unaxial compression tests, Jacobsson 2005, 2007 tested the intact and jointed granites, which were taken from the potential site for high-level radioactive waste (HLW) disposal of Sweden. However, no significant difference in strength or modulus was found. The above research results are inconsistent and it indicates the complexity of the mechanical properties of natural joints."

Jan 1, 2015

By E. V. Konopleva, H. J. McQueen

Steels in high variety have been providing strength and ductility for more than a century mainly through complex heat treatments following hot shaping. The economical and sustainable goal was a steel with the two operations combined through applying knowledge of dislocations and strengthening mechanisms aided by new mechanical and microstructural techniques. Primary hot reversing-mill rolling produced static recrystallization (SRX) between every pass to significantly finer grain size. Hot torsion showed that with lay-on temperature and rate of reduction suited to gradual precipitation of minor additions of Nb, the austenite grains would become highly pancaked; the existence of very fine subgrains along the grain boundaries (GB) could be deduced from tests on stainless austenite. The HSLA strip had to be water-jet cooled immediately to prevent SRX at austenite GB and ensuring complete transformation to ferrite avoiding grain growth after coiling. Confirmation on old mills and successful product led to the design of more flexible mills for wider range of compositions and products. A significant one was auto bumpers that reduced crash damage. More crack-resisting compositions were developed for strip welding into line pipe for arctic oil transport. Lower metal consumption and easier fabrication has resulted in more sustainable welded bridging.

Jan 1, 2015

By H. L. Snyder

This paper outlines the approach to the underground construction work involved in the Churchill Falls Power Project. It is the first in a series of papers which CIM Bulletin plans to publish as the different 11hases of this large-scale operation evolve.

Jan 1, 1968

By M. W. Bartley

DURING the field season of 1938, the Ontario Department of Mines assigned a combined geological and geophysical survey patty to the investigation of the location, genesis, structural relationships, and economic possibilities of the hematite deposits at Steeprock lake. The investigation was carried out by detailed mapping of the rock exposures and a magneto-metric survey of the drift-covered portions of the area. This was supplemented during the winter of 1938-39 by further geophysical work conducted on the ice. Dr. A. A. Brant, of the Department of Physics, University of Toronto, was in charge of the geophysical work for the Department of Mines in the summer and for the Sterola Exploration Company in the winter. The writer supervised the geological examination. Scope of the Paper The present paper is an attempt to acquaint the members of the Institute with the structure and mode of occurrence of the deposits, since many people are of the erroneous opinion that they are analogous to the Mesaba and Michigan deposits. It is hoped that, from this discussion, they may be able to draw some conclusions of their own regarding the nature of the deposits, and the importance and future possibilities of the region.

Jan 1, 1939

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

By W. Dong

This paper presents the fundamental study of the temperature distribution in a reforming planar solid oxide fuel cell (SOFC) using mathematical modeling and experimental testing approaches at Versa Power Systems (VPS). In order to investigate the on-cell temperature distribution under high rates of Natural Gas direct internal reforming (DIR), both the computer simulation approach and the experimental testing approach have been developed. In this work, comprehensive in-house DIR and SOFC models were developed and employed for the computational fluid dynamics (CFD) based 3D computer simulation. The current SOFC module has been corrected to take into account both the on-cell electrical leaking effect and the stack stage structural resistance. Meanwhile, an instrumented single-cell test jig with multiple thermocouples was built, and a series of experimental tests were performed at various conditions. The numerical results based on the single-cell jigs are in very good agreement with the physical test results.

Jan 1, 2005

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By J. Bruce See

INTRODUCTION This symposium at Cu 2019 has been organised to honour and celebrate the career and achievements of Dr Phillip John Mackey, an internationally recognised expert in the production of non-ferrous metals, especially copper and nickel smelting and refining. Phillip was born in Epping, a suburb of Sydney, New South Wales, Australia on 19 April 1941 and is one of 4 children of Gilbert and Philomena (nee Bartlett) Mackey. After completing Primary School in Epping, he attended Marist Brothers High School in Eastwood, Sydney and graduated in 1957 as the Dux of the School. Phillip’s father, being on the staff of the Sydney Technical College, in Ultimo, Sydney had the opportunity in the early 1950s to meet the late Professor Sir Rupert Myers, Foundation Professor of the School of Metallurgy at the New South Wales University of Technology (later called the University of New South Wales or UNSW). Gilbert Mackey was impressed by the new young Professor of Metallurgy and encouraged his son to study metallurgy - at the time an expanding industry in post-war Australia. EDUCATION AT THE UNIVERSITY OF NEW SOUTH WALES Phillip commenced at UNSW in 1958, graduating with honours in 1963. His undergraduate education and training included a few years of part-time study while working at British Motor Corporation on sheet metal forming of car bodies. At University Phillip developed his talent for teamwork. He was a contributing writer to the University newspaper, Secretary of the UNSW Students’ Union and was active in the UNSW Metallurgical Society and co-editor in 1963 of “Metallurgical Review,” the annual journal of the UNSW Metallurgical Society. His diverse interests and curiosity about the world around him were likely nourished while at University. Upon completing his Bachelor’s degree, Phillip was awarded a Commonwealth of Australia Postgraduate Research Scholarship. He began his PhD in 1964 on the thesis topic “Studies in Heat Transfer between Dispersed Liquid Metals and Gaseous Atmospheres” working under the supervision of then Associate Professor Noel Warner, an outstanding Professor at the University. Professor Warner is now an Emeritus Professor at the University of Birmingham and is internationally respected for his pioneering theoretical and practical work on established and innovative smelting processes.

Jan 1, 2019

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By J. Trojacek

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20th century. Many uranium deposits were discovered in the territory of the Czech Republic. Over a period of 50 years approximately, 110 000 tons of uranium in concentrate were produced. Different mining methods were developed and used. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere ? Straz pod Ralskem where both mining methods ? the underground mining and the acidic in-situ leaching ? were used. The extensive production of uranium led to widespread environmental impacts and contamination of groundwaters. Over the period of ?chemical? leaching of uranium (ca. 32 years), a total of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approximately 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers an area larger than 27 km2. The influenced volume of groundwater is more than 380 million m3. The total amount of dissolved SO4 2- is about 3.6 million tons. Approximately 0.5 % of the contamination is located in the Turonian aquifer. After 1990, a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. The objectives of the remedial activities are the followings : to restore the aquifer to a condition guaranteeing continuing usability of Turonian water of Northern Bohemia Cretaceous, to decommission boreholes and surface installations and to incorporate the surface of leaching fields into the ecosystems taking into account regional systems of ecological stability and urban plans. Nowadays four main remedial technological installations for reaching of these aims are used - the ?Station for Acid Solutions Liquidation No. One?, the ?Mother liquor reprocessing? station, the ?Neutralization and Decontamination Station NDS 6? and the ?Neutralization and Decontamination Station NDS 10?. Total capacity of this complex is sufficient to reach the target values of remedial parameters in 2037. The remediation action consists of: pumping of residual solution to the surface, separating uranium from the solution and reprocessing contaminants into commercially usable or ecologically storable products. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 1.5 billion EUR.

Aug 1, 2013

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

"A new method for oxidative destruction of cyanide in industrial waste waters and slurries, such as gold mill barren liquors, tailing slurries and flotation tailings has been developed at the Inca research laboratories. Rapid decomposition of cyanide and related species is attained by treating the waste waters with a mixture of S02 and air at controlled pH and in the presence of a small amount of copper which acts as a catalyst. The approach selectively oxidizes cyanide and metal cyanide complexes, and also removes iron cyano complexes which are not removed by alkaline chlorination.The new method is shown to be less reagent intensive and therefore more economical than alkaline chlorination for treating gold mill and flotation waste waters. INTRODUCTIONOver 90% of the gold mined in Canada is extracted from the ore by ""cyanidation"". Wastes from the process consist of tailings which contain free cyanide, cyanide combined with heavy metals, thiosalts and thiocyanates. Because of the concern over the effect of toxic cyanides on the environment, all cyanide containing effluents will have to be treated in the future to meet certain government set concentration limits."

Jan 1, 1982

By G M. Thorpe

This paper discusses mine research at Inco, giving specific examples of research projects which illustrate the approach to mining problems. The first example covers the development of a new mining method, "undercut and fill," which was originated for mining badly broken-up pillars, but which is now rapidly replacing the square set method of pillar recovery. In the new method, ore is extracted in a series of successive horizontal cuts, progressing downward, a cut being completely mined and filled before the cut below is started. In the second example, improvements to the "cut and fill" method of mining are discussed. These improvements are the result of improved techniques and improved equipment, etc., with, in many cases, the former being made possible by the latter. The advances made have permitted the use of the "cut and fill" method at much greater depths than before. The third example is presented to illustrate research undertaken to obtain the earliest maximum advantage of the introduction of a new piece of equipment or material. For this purpose, the development of the "Under-ground use of AN /FO Blasting Agent " has been selected. Work on this project started in May, 1960, at a time when there was very little in-formation regarding the potentialities of AN /FO for underground blasting, either primary or secondary. By the end of 1961, AN /FO made up 64 per cent of the explosives used under-ground at Inco mines.

Jan 1, 1963

By C. A. Sosa-Blanco

Minera Sabinas in central Mexico treats a complex sulfide ore containing galena, chalcopyrite, sphalerite and argentite as valuable minerals, and in some cases important amounts of non-magnetic pyrrhotite. For high pyrrhotite ores, results obtained by selective flotation showed good grades and recoveries in the lead-copper circuit, but a commercial zinc concentrate could not be produced due to the high floatability of pyrrhotite. When this is the case, an alternative method was proposed to produce a bulk concentrate by flotation which is then leached to recover copper and zinc from liquor in a SX-EW circuit. Leaching was conducted in an autoclave in order to study the effect of temperature and pressure, but bioleaching tests were also conducted. Leaching lead-silver residues were treated by cyanidation in order to recover silver values. The results obtained by selective flotation and by bulk flotation with leaching of the bulk concentrate showed that the latter alternative increased zinc recovery by 30 % with similar recoveries of the other metals.

Jan 1, 2007