Search Documents

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By Z. Jing, C. Jun

High-purity Bi2O3 was prepared via extraction-preparation stripping method use BiCl3 leaching solution. Parameters such as oxalic acid concentration, phase ration, aging duration, feeding duration, were examined for their effect on the size and morphology of precipitate. The precipitate was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), particle size analysis, differential scanning calorimetry and thermal gravity analysis (DSC-TGA) and infrared spectroscopy analysis (FT-IR). Bi2O3 was characterized by elements analysis, particle size analysis and scanning electron microscopy (SEM). Bi2O3 product of 680 nm was obtained using 15 g/L oxalic acid, 1/1 phase ration, 0 min aging duration, 0 min feeding duration and calcinating at 500 °C for 2 h.

Mar 1, 2018

By Timothy J. Orr, Jami M. Girard

A NIOSH study on occupational deaths between 1980 and 1989 indicated that in the United States, mining had the highest average annual fatality rate (3 1.9 per 100,000 workers) of any other major industry. Since "lack of training" was often cited as the primary cause of accidents, NIOSH has been investigating new methods for effective training. One such method is the use of low- cost, desktop computers to simulate a virtual mining environment. Computer-based training offers several advantages over conventional training because the computer programs provide a three- dimensional environment that allows the trainee to practice using evacuation routes, encounter mining hazards, and view mining operations without being exposed to any real danger. One major focus of the project is mine escapeway multiuser training using desktop virtual reality programs. Researchers have imported mine maps into the software for the purpose of practicing actual evacuation routes and procedures. Various scenarios for evacuation can be practiced in a three-dimensional computer simulation of the mine in a disaster situation, complete with smoke, fire, and other dangers. Depending on the trainee's job description (i.e., foreman, shift boss, beltman, etc.), certain tasks need to be performed in addition to navigating primary and/or secondary escape routes. Each scenario allows for individual or team-based training and provides a means to educate mine workers in hazard recognition and hazard avoidance. Using this program, mine workers can practice evacuating various mine layouts without the danger and expense associated with escapeway training in an actual underground mine. Each scenario can be changed to test the trainee's reaction in a variety of circumstances and run many times so the trainee can practice concepts. This training experience will help reinforce the knowledge acquired during more conventional classroom instruction, and the inherent flexibility of the program allows training materials to be tailored to meet the specific requirements of individual mines.

Jan 1, 2002

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By Angel Rafael Arce Chilque

Um estudo visando à caracterização metalográfica e metalúrgica foi realizado em um aço ARBL (alta resistência e baixa liga) tipo X80, soldado com o processo arame tubular (FCAW) robotizado, com três diferentes níveis de energia de soldagem. Para tal foram utilizadas técnicas de metalografia óptica e microdureza Vickers (Hv). Foram depositados cordões de solda em forma de camadas sobre chapas do aço X80, variando a energia de soldagem e sem pré-aquecimento, no estado como soldado. Os resultados mostram que a técnica de sobreposição utilizada, com baixa e média energia de soldagem, não foi suficientemente adequada para melhorar as propriedades metalúrgicas dos cordões depositados anteriormente, inclusive da ZTA do metal de base.Os cordões depositados com alta energia de soldagem promoveram crescimento do tamanho de grão da GGZTA do aço X80 com a consequente diminuição da resistência ao impacto.Este trabalho da subsídios para uma melhor compreensão das soldas multipasses.

Aug 16, 2017

By Martha Gross, Amanda Wachenfeld, Brian Keaney, Jean-Michel Charpentier, Frank Perrone

The Hampton Roads Bridge-Tunnel (HRBT) Expansion widens the existing four-lane bridgetunnel corridor to eight lanes through construction of two parallel tunnels, interstate widening, and bridge expansions. As part of the design-build contract, a supplemental geotechnical investigation was completed to support the design. The investigation for the subaqueous tunnel segment consisted of over 48,400 linear feet of drilling and 7,100 laboratory tests. This paper discusses the challenges of planning and executing a large-scale geotechnical investigation for underground works in a marine environment and the use of big data for effectively managing, interpreting, and transmitting data to the design-builder consistently throughout the investigation.

Jun 23, 2024

By Otto Sandoval Zea

En la actualidad, existen equipos que analizan los daños colaterales producidos por la voladura como el uso de sismógrafos, los que son aplicados para el control de los limites permisibles de vibración en construcciones superficiales, de forma que permiten realizar análisis de vibración en condiciones subterráneas (Minas) y establecer parámetros que generen un mejor diseño de excavación en el avance y producción. En esta perspectiva, el presente texto para predecir el daño generado por los explosivos y la reducción de los mismos, emplea el análisis vibracional, donde se determina un comportamiento de atenuación de la velocidad vibracional de partículas en función a la distancia y la carga operante* representado por una curva exponencial denominado “Ley de Atenuación de Vibración de Partícula”, que difiere según la calidad del macizo rocoso y la potencia del explosivo empleado.

Sep 14, 2009

By Rafael Alves Frederico de Alencar

O comportamento mecânico dos diferentes tipos de materiais é influenciado por diversas variáveis, dentre as quais, as condições adotadas para o processamento mecânico dos mesmos, as características estruturais e os aspectos metalúrgicos, por exemplo. Considerando essas variáveis, este trabalho apresenta o estudo do comportamento mecânico do aço inoxidável ferrítico AISI 430, estabilizado ao nióbio, para diferentes modos de pré-deformação: estampagem (estiramento) e tração com o subsequente carregamento em cisalhamento. Os resultados indicaram que o comportamento mecânico do material variou em função da direção de aplicação do esforço mecânico e do modo usado para a pré-deformação desse aço, ocasionando endurecimento e amaciamento.

Aug 17, 2017

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of 'heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995

By Laura Suarez, Jörgen Kajberg, Pär Jonsén

In recent years, slag, a residue from pyrometallurgical processes, has become more attractive in circular economy frameworks to increase the efficient use of resources throughout the life cycle of steel products and help in the reduction of carbon emissions. Its applicability is strongly dependent on the particle size, and therefore, the optimization of breaking processes should be approached by increasing the knowledge of the dynamics of slag to promote fracture. Increasing the knowledge on themechanical response ofmanganese slag opens up the potential for the development of cost-effective numerical models, e.g., constitutive models based on inverse engineering calibration frameworks or digital twins. In this study, rate-dependent tests of manganese slag have been performed using a split Hopkinson pressure bar device for testing its dynamic mechanical response. In order to obtain information about the crack initiation and fracture process, 2D ultra-high speed imaging was implemented with a sampling frequency of 663,200 fps for diametrically loaded specimens. Full-field deformation measurements using digital image correlation (DIC) techniques showed a staggered fracture process where failure points on mechanical response curves vary due to the internal events happening in the material. Localized frictional occurrences and inertial effects acting inside the pre-cracked matrix have a strong effect on the global mechanical response, and therefore, a great variability of strengths was obtained.

Nov 3, 2023

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By R Stosch, D Lohberger, J Rodler, E Schnell and A Bassler, H Ramseier

In the last two decades three-dimensional (3D) computational fluid dynamics (CFD) simulations have become an important tool in engineering sciences. More recently, the safety requirements in underground railway stations have increased with regard to incidents. For this reason, existing underground stations (eg Munich, Strasbourg and Berlin) are being equipped with smoke extraction facilities to protect passengers from smoke and visibility impairment in the event of fire. In addition, designs of planned underground stations (eg Karlsruhe, Doha) also include these facilities.For the commissioning of ventilation engineering systems with complex structures, the functional testing of the whole technical installation are important, as are the acceptance tests of ventilation and equipment parts. This functional testing includes not only the technical inspection of the equipment but also the acceptance measurements of the capability of the equipment and the execution of hot- or cold-smoke tests to confirm the effectiveness of the ventilation system.Due to the fact that the overhead contact line and other sensitive installations were already installed in the tunnel roof at the time that smoke tests were proposed, hot-smoke tests with fire loads up to a maximum of 1 MW could only be executed. Therefore, the evidence of the attainability of the safety objective had to be provided computationally in this special case with a fire scenario of a heat release of 10 MW using CFD simulations.This paper presents the interplay between the results from acceptance testing and smoke tests and the use of 3D CFD simulation and virtual reality using the example of Allmend station, which was repositioned underground and is part of a new section of track from Lucerne railway station to Kriens in the Zentralbahn network. The steps of the verification and validation of the computer model are presented with the real tests and measurements.CITATION:Stosch, R, Ramseier, H, Lohberger, D, Rodler, J, Schnell, E and Bassler, A, 2014. Safety in underground railway stations – an example of the interplay between testing and 3D computational fluid dynamics simulation, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 103–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By W. W. Agey

This report summarizes results of bench-scale metallurgical studies by the Federal Bureau of Mines on three composite samples representative of the low-grade manganese ores purchased by the General Services Administration (GSA) and stockpiled at Deming, N. Mex., and Wenden, Ariz. Bench-scale flotation tests at the Salt Lake City Metallurgy Research Center showed that all three composites could be beneficiated by flotation to recover 88 to 90 percent of the manganese in concentrates that assayed from 38.5 to 39.0 percent Mn, 10 to 12 percent insoluble, 5 percent CaO, 3 to 5 percent Fe, and 1.3 to 1.7 percent combined Pb plus Zn plus Cu, Sintering studies indicated that specification-grade material could be made from these concentrates by sintering above 1,000° C, and adding either sodium or calcium chloride to the charge to insure removal of enough lead and zinc to meet the specifications.

Jan 1, 1962

By M. L. Whisman

The Bureau of Mines developed and tested in the laboratory several innovative techniques for reclaiming used lubricating oil. These processes included percolation through both chemically treated clay and ion-exchange resins, distillation through batch and continuous wiped-wall vacuum apparatus, treatment with solvent extraction systems, and chemical removal of impurities with chelating agents. In each treatment, the criteria of evaluation was oil recovery and reduction of acidic and metallic components. Both vacuum distillation and solvent treatment ranked high in their abilities to remove acidic and metallic components of the used oil with good oil recoveries. A combination of the two techniques gave the best overall results in terms of quality evaluations made by established bench tests. The methods were not ranked according to economic practicablity.

Jan 1, 1974

By Noan Tonini SImonassi

Compósitos cerâmicos de TiB2-AlN foram preparados por técnica de “spark plasma sintering”. A densidade máxima relativa e resistência foram de 96,9% e 16,2 GPa, respectivamente. As amostras foram submetidas a testes de usinagem de curto tempo. Os compósitos com 70% de AlN foram utilizados como ferramenta de corte e apresentaram resultados satisfatórios para os parâmetros de corte. Análises de Microscopia Eletrônica de Varredura (MEV) permitiram a análise da microestrutura e o desgaste da superfícies após os testes de corte.

Oct 30, 2017

By Chuan-fu Zhang

The fibrous precursor can be obtained by coordination precipitation process, using oxalate, cobalt chloride and ammonia. XRD pattern of precursor precipitated at pH=9.0 is different from that of ß-CoC2O4?2H2O precipitated at pH=1.0 which indicates that the precursor powders are one type of cobalt complex. According to the results of element analysis and IR spectra, it can be inferred that the composition of the precursor is [Co(NH3)x]C2O4?H2O(x=1.2?..6) formed by the coordination reaction at pH=9.00 in the Co(II)-C2O42--NH3-NH4+-H2O system. It?s found that the fibrous cobalt powders greatly inherited the morphologies of the precursors. Many factors could affect the formation of the fibrous cobalt precursor powders, such as the initial Co2+concentration, pH value and so on. The SEM images show how they influence the morphologies of the precursor powders. By adding proper surfactant, the dispersion of the precursor powders would be improved. At last, the final product-fibrous cobalt powders which are about 0.3~0.5min size and 40~60 in aspect ratio were produced by thermal decomposition of fibrous cobalt complex at 400~500°C in the weak reducing atmosphere.

Jan 1, 2006

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 ± 5 km and 350°C??-??550°C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950