Search Documents

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

By Fletcher G

This paper will outline the design process, and the constmction and rehabilitation techniques proposed for the external waste dumps associated with the mining of the Wolfang Basin coal measures.The basin is located to the north of Clermont and immediately west of the Bowen Basin in Central Queensland, Australia. Development of the Clermont Coal Mine is planned for the mid-1990s after adequate sales commitments are obtained to allow the project to proceed.

Jan 1, 1992

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

By White B

A novel approach is suggested for the solution of planning and development problems in the coal, mining industry. The formation of coal measures depends to a significant extent on sequential geological processes and events which are probably best defined in a "system of processes and responses." The great number of variables in such a system is a characteristic feature of geological environments. Research work over the past two decades, in particular, has successfully established analytical procedures for the identification and definition of relevant and irrelevant variables for mining developments in specific geological situations. Such situations are typifiable within the regional geological setting of coal deposits. Scale gaps can be bridged by reliance on common symmetrical attributes and pervasive geometric features. Depositional processes and their resulting attributes are responsible for the development of mechanically significant rockmass "defects" and anisotropies; such features have to be identified and assessed for the selection of colliery design criteria. It is suggested that the procedural frame- work of systems engineering analysis is a most appropriate tool for the assessment of those geological features that can influence the mechanical behaviour of the "floor-seam-roof" system in "high technology" mining operations of the future. It is anticipated that the overall emphasis of future mining systems will be toward the use of larger scale more highly productive methods and machines, with higher capital outlay but

Jan 1, 1987

A simulation model of the load and haul process where the loader cycle has been subdivided into its individual components is used to consider the benefits derived from improved drill and blast methods. Field data from a Hunter Valley mine is u

Jan 1, 1998

The growth of the mining industry around Australia over the last ten years has seen many open cut mines developed on shallow oxide reserves. Most of these have been gold operations, although there are some copper mines in the list, too. Many of these have exhausted their oxide reserves and have made the transition to underground mining to access their deeper sulphide ores. Other operations have reached or are approaching the point where the decision has to be made to go underground or cease mining. This paper discusses the issues involved in making the transition from surface to underground mining. The aim is not to discuss each of the issues exhaustively. This would take a conference in its own right. Nor is it intended to provide a primer on underground mining. Instead the aim is, firstly, to flag the issues which must be addressed when planning to make the transition from surface to underground mining and, secondly, to identify critical aspects of mine development.

Jan 1, 1997

By G Johnson, S Michalek, N Redman

As the modification of the 2009 Mill OperatorsÆ Conference theme from æmilling through the boomÆ to æthe boom û experience gained and lessons learnedÆ exemplifies, comminution practitioners are facing a series of challenges in the dramatically changing mining environment. One of the main problems plant managers have been facing during the boom times has been the severe metallurgy skills shortage and high staff turnover, both factors that can cause difficulties in mill liner management. Many of todayÆs mill managers are now also more than ever faced with the need for cost-cutting in order to continue operating viably. Amongst other potential target outcomes such as maximised throughput, MillMapperÖ, a tool for mill condition monitoring and mill performance optimisation, can be utilised to address these issues. This paper demonstrates how MillMapperÆs quantifying decision making tools can serve to be in control of managing mill liner and production issues, and how it can form the basis for mill cost savings without the risks normally associated with conventional methods or the lack of using any condition monitoring methods. MillMapperÖ is currently being referred to at a rate of approximately 150 surveys and associated reports per annum at processing plants in Australasia, South America and Africa. Examples throughout the paper provide insight into how the presented sample set of users have extracted benefits that could have otherwise not been safely or at all achieved.

Jan 1, 2009

By McKew M, OÆRegan

Rapid access longwall mining' or 'longwail punch mining' is a proposed extraction method whereby longwall gate roads are driven into a seam directly from an opencut highwall. The longwall panel thus formed is retreated back to within 40 m of the highwall providing an extremely simple, reliable and therefore highly productive longwall mining system. The concept is of particular benefit for the recovery of isolated pockets of coal (adjacent to a highwall) not easily accessible from a conventional underground mine. As panel gate roads are driven directly from the open strip, minimal delays are incurred between the end of open cut and start of underground production, allowing the method to bridge the gap between open cut mining and a total underground commitment. The study was specific to the Bowen Basin, and given the likely conditions, no significant operational or geotechnical hinderances to the concept could be identified. It was therefore concluded that longwall punch mining would not expose the operator to any additional risks above that normally associated with the introduction of longwall mining. Thus, longwall punch mining is an attractive option, both operationally and financially, for open cut mines reaching their maximum economic Death.

Jan 1, 1988

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

It may at first sight appear somewhat presumptuous for the writer to attempt to discuss a subject in which he cannot pretend to possess any special scientific training; but a sufficient apology can surely be found in the fact that a very large percentage of the accidents from explosives occurring in metalliferous mines is traceable to the ignorance of the characteristics of these compounds by the miners who have to handle them, and to their deliberate disobedience of the rules laid down for their guidance by the manufacturers, the government regulations, or the special rules of the mines.The only method which promises any possibility of improvement upon these conditions is to substitute reason and understanding for the rule-of-thumb principle which says "you should do this" or "you should not do that." In the one case his own knowledge and intelligence enables the miner to avoid any dangerous practice in the other his inclination prompts him to do anything which will save time, provided he is not found out or at best trusting to his memory to tell him what is dangerous, without the reasoning which makes that memory easy.Another evil of rule-of-thumb knowledge is that, from its very nature, it prevents adaptability, and so we find that old miners, who learnt blasting in the days of black powder, cannot understand why high explosives do not require heavy tamping, or because copper bars are permitted in tamping powder they should not be used with other explosives...

Jan 1, 1903

By L Crew, S Jackson

A trial of an Adept Online Ore Sizer (OOS) was undertaken at the WMC Leinster Nickel Operation (LNO) in the first half of 2000. During this time the On Line Ore Sizer has been shown to be a robust and accurate instrument for measuring mill feed ore size. Data collected during the trial indicates significant variation in the F80 of the SAG mill feed. The effects of feed size on milling parameters such as mill weight, mill power draw and mill efficiency appears to be dependent on the ore blend treated. With some ore blends a weak positive correlation was found between ore size and mill weight and milling efficiency but with others no correlation is evident. It is believed that the OOS will become a vital piece of equipment in the future as LNO continues to optimises its milling circuit.

Jan 1, 2000

This is a brief introduction of a sewer pipeline constructed with a pipe jacking method in combination with a 1 200 mm finished inner diameter tunnel boring machine developed for the first time in Japan. The pipeline is located under a national highway running through a densely built urban area and is 185.7 m long and 2.9 m to 3.7 m deep from the ground surface. The geological features along the pipeline show mostly slate and partly silt. The pipeline was constructed with a newly developed multi-application type tunnel boring machine equiped with a fluid transport system. The construction consisted of tunneling by a tunnel boring machine followed by pipe jacking operations. The excavated materials were dis- charged off the tunnel by a fluid transport System.

Jan 1, 1987

By Hendrix J. L, Nelson J. H

A study was conducted to examine how pretreatment of carbon-bearing gold ores with chlorine enhances gold recovery by cyanidation. It is hypothesized that metal species (including iron and copper) dissolved during chlorination adsorb on the carbon surface hindering the adsorption of dissolved gold. To test the hypothesis, samples of several sulfide minerals were subjected to reaction with sparged chlorine gas to determine which, if any, dissolve faster than gold under these conditions. Then, a synthetic carbonaceous refractory gold ore containing pyrite, chalcocite, activated carbon, and gold was subjected to gas sparging. The results of these experiments showed that chalcocite and arsenopyrite dissolve so that metal (copper and iron) is put into solution slightly faster than gold under the same chlorination conditions. Also, it was observed from the experiments that gold adsorbs on activated carbon during chlorination, but is replaced by copper and iron as the chlorination process dissolves more of the chalcocite and pyrite. The study concluded by investigating ferric chloride addition prior to chlorination to hinder gold adsorption on activated carbon.

Jan 1, 1991

By Jingmin Xin, Wenhua Xing, Zongxin Huo, Hongzhang Chen

Drawing up the successive plan for mining and development is a very important and regular plan work. The expert system of the successive plan for mining and development drawn up by computer is developed on the basis of network, computer simula

Jan 1, 1998

By Conochie DS

SIROSMELT is a successful new pyrometallurgi- cal furnace system using a top-entry lance which can be submerged in both slag and matte. The lance is of simple construction, and is cooled by process air. Pilot plant work commenced in the CSIRO Division of Chemical Engineering in 1972 using a 50 kg batch reactor. This paper traces the development of the technology through various slag cleaning and smelting processes up to a scale of 5 tonnes per hour continuous feed. Strong co- operation between CSIRO and the Australian smelting industry has contributed greatly to the success of SIROSMELT.

Jan 1, 1984

Study on Preparation and Gel Performance of High Purity Montmorillonite In order to research the colloidal and thixotropic performance of the inorganic gel prepared by high purity montmorillonite, this study uses the moderate grade bentonite ores from Weifang (China) as raw material. Two-stage hydrocyclone classification was applied to obtain the high purity montmorillonite with its content of 94.8 per cent. In contrast to other methods of montmorillonite purification, two-stage purification by hydroclone has the advantages of larger throughput and easily achieving auto-control in industry, and purified products with different montmorillonite content can be obtained by this method. And then the inorganic gel was prepared by the prepared high purity montmorillonite and its colloidal and thixotropic performances by measuring the flowability and thixotropy were further studies. Research results show that the inorganic gel has plastic body liquidity, the viscosity decreases with the increase of the shear rate, the static and dynamic shearing stress values are 33.98 Pa and 91.89 Pa, respectively, and the thixotropic value is 95.2 dyne+s/cm2, which indicates that it has preferable colloidal and thixotropic performance. Montmorillonite inorganic gel prepared by bentonite with high montmorillonite content and low-layer charge has better gel performance.

Sep 13, 2010

The role of metals in the economy is discussed with regard to the flow of metals through to final demand and is illustrated by data for seven metals. Factors influencing the changing pattern of metal consumption are described, including relative prices. A des- cription and discussion of current metal demand forecasting methodologies precedes a discussion firstly of broad economic trends and secondly of the evolving pattern of metal consumption relative to GDP (metal consumption intensity), as technology and other factors change and as economies mature. The tendency for metal consumption intensity to plateau and decline when economies reach a certain region of per capita GDP, following a rapid rise early in the industrial- ization process, is shown in comparative data for seven metals and six countries.

Jan 1, 1979

By A Hewitt

Portland cement is the chief binding ingredient in mine backfill. In the presence of water, the chemical compounds within portland cement hydrate causing hardening and strength gain. During hydration, heat is generated. In certain cases, hydration heat may be produced significantly faster than it can be dissipated, which can create high temperatures in the underground environment. This paper presents the results of a series of investigations aimed at quantifying the heat generated by cemented backfill during hydration. Scaled stope models, instrumented with thermistors, were used in the investigation. Heat transfer to the hanging wall, orebody, footwall and cross-cut and production drifts was assessed during the backfill curing process and relationships between cement content, cure time, and heat generation were developed. The results of this work will assist mine operators in predicting the heat generated by cemented backfill and provide the necessary information to implement effective engineering control of heat in the underground environment.

Jan 1, 2005

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975