Search Documents

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By J. B. Pullen

THE United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruffner and associates in 1877. In 1888 the late Senator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 189o to date. GEOLOGY The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre-Cambrian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-ft. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. A plan and vertical section of the mineralized zone showing the principal geological features is shown in Figs. I and 2. GENERAL DESCRIPTION AND PHYSICAL CONDITION OF MINE After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes -mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became difficult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1941

By William R. Chedsey

IN the last two years the E.C.P.D. committees having to do with the inspection of engineering schools for possible accrediting have been concerned with the engineering content of some of the mineral industries courses. Originally the discussion arose with regard to engineering geology, or geological engineering, afterward broadening to metallurgical engineering, ceramic engineering, agricultural engineering, and other branches not pertinent to this discussion. Some members of visiting committees took the attitude that they probably would have to accredit these types of training as included in the engineering group if they met the average standard set by the mining schools, though they questioned -whether they were really engineering.

Jan 1, 1939

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

By Will H. Coghill, J. Bruce Clemer

Flotation has been so closely allied with the sulfide minerals and their early and associated oily reagents that the term "oil flotation" has erroneously been applied to the entire flotation process. Today, the term "chemical flotation" might be used to advantage. Flotation literature has dealt primarily with the removal of sulfides from non-sulfide gangues, and the separation of one sulfide from another. Now, the application of the process to the separation of nonsulfide minerals is coming to the fore; and from the standpoint of the number of commercial minerals involved, the flotation of nonsulfides offers the larger field. Here, soap or soap-forming substances, such as the fatty acids and their derivatives, are used; hence there may well be a subdivision of the chemical flotation process called "soap flotation." Early experimenters learned that it was easy to form a froth or foam that would carry a part or all of the ore charge over the lip of the flotation machine; but this could not be regarded as flotation because of the lack of selectivity. Doubtless soap was one of the first reagents tried, and doubtless it was rejected on account of its gangue-carrying properties. Now this same gangue-carrying ability makes soap an acceptable reagent, for we are dealing with that which, among sulfides, is considered "gan-gue." As in the flotation of sulfides, so in the flotation of nonsulfides, the selective flocculation of the mineral and the dispersion of the gangue are the first objectives. In fact, these two phenomena epitomize flotation. They depend upon the unlike surface properties of the respective minerals; and as long as the components of an ore have unlike surface properties, a separation is possible, at least in theory. Often in nonsulfide flotation it makes little difference which mineral floats and which is depressed; generally only a separation is sought.

Jan 1, 1935

By A. D. K. Laird, John A. Putnam

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By John A. Putnam, A. D. K. Laird

This paper describes the application of x-ray theory to design procedures in connection with fluid saturation determinations during fluid flow experiments with porous media. A reliable and rapid method for calibrating the x-ray apparatuy is described. Extension of the method to fluid saturation determinations in three-fluid systems is described. INTRODUCTION In rerearch on oil production problems a method is required which will give quickly the quantity of each component of a fluid flow system present at any cross-section of a porous medium. The sample of porous medium under investigation is usually referred to as a core. The ratio of the volume of one component to the total fluid volume is defined as the saturation of the porous medium by that component. This ratio is generally given as per cent saturation. Some means of measuring saturation which have received consideration include: electrical conductivity of the fluids;1,2 emissions from radioactive tracers dissolved in the fluids; the radioactivity of silver caused by reflection of neutrons from hydrogen atoms in the fluids;' the attenuation of a microwave beam. the diminution and phase shift of ultrasonic wave trains.4,5 and the reduction in intensity of x-ray beams in passing through the fluids. X-rays have already been used with some success. Since every material has a different power to absorb x-rays, the reduction in intensity of an x-ray beam as it passes through a core depends on the fluids present. The strength of the emergent beam can be found by converting its energy into a measurable form such as heat or ionic current. or by its effect on a photographic plate or fluorescent screen. The beam strengths could be interpreted as quantities of known fluids in the core if, previously, these beam strengths had been identified with a known combination of the same fluids. With some fluid cornbinations it might be desirable to dissolve powerful x-ray absorbing materials in one or more of the fluids, to increase the differences in the beam strengths for various fluid saturations. Boyer, Morgan and Muskat6 have described a method of measuring two component fluid saturation. One component was air or water; the other. minerat seal oil in which was dissolved 25 per cent by weight of iodobenzene to increase its absorbing power. The x-ray source was a tungsten target tube operated at 43 kv potential. The beam emerging from the core was measured as ionic current flowing across an air-filled ionization chamber by means of an amplifying circuit and galvanometer. Another portion of the beam from the x-ray tube was passed through a metal plate and measured in another ionization chamber. This portion, called the monitor beam, was used as an indication of the performance of the x-ray tube. The galvanometer readings were calibrated against air-oil core saturations, gravimetrically determined. The method was apparently established by experimental means. In the present investigation the available theory of x-radia-tion was surveyed with a view to extending the usefulness of the method and to developing design procedures for its application to measurement of fluid saturation in porous media. Application of the theory permits prediction of relative meter readings to be expected for any combination of porous matrix, various saturating fluids and auxiliary filtering media. It is thus possible to calibrate the equipment in terms of fluid saturation by an indirect but rapid technique. The results of calculations based on x-ray theory indicate. and results of the saturation calibration technique confirm. that a valid measurement of the saturation of the core can be made for any two components and in some cases for three components. THEORY The strength of an x-ray beam, after it has passed through a distance. 1, of matter of density, p, and mass absorption coefficient, µ at a given wavelength, A, may be expressed by the absorption formula I = I0 e ...........(1) where I, represents the intensity of the incident x-ray beam and I is the intensity of the emergent beam. The expression e is called the transmission factor of the material. The variation of I,, with wavelength depends upon the materials through which the x-ray beam has previously passed and upon the spectral distribution of energy at the source of the x-radiation. A group of curves. called spectra. which show the variation of intensity with wavelength and x-ray tube voltage are given in Fig. 1. These curves represent the general radiation from a tungsten target tube. When the tube voltage is greater than 69.3 kv, the characteristic radiation of the tungsten is emitted and is superposed on the general radiation. At a given voltage the minimum wavelength A,,,,, at which energy can be emitted by an x-ray tube is given by the formula 12,340 xml. = ——..........(2) volts where A,.,,.. is in Angstrom units. The wavelength at which the spectra have maximum intensity a1so decreases with increasing x-ray tube voltaue. The area under each curve represents to an arbitrarv scale the total energy emerging from the x-ray tube for that voltage. The variation of µ with wavelength has been determined for many substances and may be found in such references as those by Compton and Allison7 and by Hodgman.8 The phenomenon of absorption is composed chiefly of the capture of photons by the atoms of the absorbing material with associated displacement of electrons, and of the scattering, or the deflection, of the photons by the atoms. Curves of these mass absorption coefficients show jump discontinuities. or absorption edges. at wavelengths which are short enough for the photons,

Jan 1, 1951

By A. T. Shurick

TILE present economic crisis in bituminous coal is substantially the most insidious, and critical, in the modern history of the industry. The large consumption deficit that has gradually developed (almost unawares), has culminated in a situation that has forced home the urgent necessity for prompt and radical remedial measures, such as the various mergers now in course of negotiation. Conditions today are sufficiently comparable with those in the iron and steel industry, preceding the formation of the United States Steel Corpn., to suggest the possibility of a sweeping super-consolidation, that all but staggers the imagination. The important function of the banker in this, and lesser projects, is too well known to require comment, and it is important that we understand clearly just what these functions are. Certain features in banking practice came up for consideration in connection with a rather exhaustive economic study into the prospective future of the coal industry, upon which I was recently engaged for an Eastern bituminous interest. This survey was made for the purpose of effecting a decision on certain pressing questions of policy, involving considerable capital expenditures, that would be compatible with the flattening out in the curve of production in recent years. An examination of the TRANSACTIONS, and the coal literature generally, failed to disclose any pertinent, and authoritative data, on this subject. This was more or less characteristic of the whole survey, which had involved a large amount of original research, and measures were taken to procure the required information. The following notes have been compiled largely from the data thus collected, supplemented with material, suggestions and criticisms, by several of the larger banking houses active in coal, together with personal memoranda of my own.

Jan 1, 1928

By L. S. Reid, R. L. Huntington, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By R. L. Huntington, L. S. Reid, Chen Chun Ku

The simultaneous adsorption of water and hydrocarbon vapor from natural gas by three grades of alumina has been studied at atmospheric pressure and temperature. Results of this investigation reveal that the presence of water vapor in the gas inhibits the adsorption of hydrocarbon vapor, although the presence of the latter does not have a pronounced effect upon the adsorption of water vapor. Adsorption of water-hydrocarbon mixtures from gas is divided into three phases. In the first, both water and hydrocarbon vapor are adsorbed; in the second, adsorption of water vapor proceeds while desorption of hydrocarbon takes place; in the third phase, the adsorbyt approaches complete saturation with respect to both water and hydrocarbon vapors. Both theory and experimental data can be applied to design and operation of commercial dehydration plants, and an illustration is presented. Introduction Dehydration of natural gas becomes increasingly important as the operating pressures employed in gas processing and transmission are increased above 500 ib. per sq. in. Gas produced from high-pressure wells is saturated with water vapor when it leaves the reservoir and it continues into the processing plant or transmission system in a saturated condition because of the substantial decrease in temperature due to expansion at the wellhead. Usually this gas is accompanied by liquid water and hydrocarbons that have condensed with the change in temperature and pressure. Without dehydration, gas temperatures must be held at relatively high levels to prevent solidification of gas hydrates. According to Hammerschmidt's data8 on the relationship of pressure to the freezing point of natural-gas hydrates, the minimum safe operating temperatures range from 55' to go°F. for pressures ranging from 500 to 3000 lb. per sq. in., respectively. Often it is difficult to maintain gas temperatures above the hydrate-freezing temperature because of climatic conditions, unless flow-line heaters are installed. Also, in processing gas for its gasoline content at high pressures, it is desirable to employ operating temperatures lower than the hydrate-freezing point. In distributing high-pressure gas, the large pressure drop from line pressure to town-gate pressure often prbduces sufficient cooling to freeze the regulators and disrupt consumer service. Therefore, it is highly essential to dehydrate high-pressure natural gas if smooth and economical operation is to be maintained at all times. Few published data are available on the simultaneous adsorption of water and hydrocarbon vapors. The literature contains many mathematical expressions for rate of adsorption in various systems but a rational correlation of the existing rate

Jan 1, 1944

By O. Bilharz

The rules laid down by Peter von Rittinger in his classic Lehrbuch der Aufbereitungskunde (Berlin, 1867, p. 513) concerning the designing of dressing-works still possess authority for such works and their operation. Nevertheless, some modifications and additions suggested by practice may be of value at the present time. Rittinger says: "I. Choose the apparatus and machines which can be, under the existing con-' ditions, easily constructed and kept in running order!' This rule contemplates the construction of apparatus (mostly of wood) on the spot, with the command of good sbops and especially of good workmen in wood. But in many cases, particularly for the sake of a prompt supply, the construction of apparatus is now left to special manufactories, which pay more attention in the choice of materials to durability and strength than to easy manipulation and erection. Nevertheless, here,as in many other instances, simplicity of construction and solidity of execution are to be recommended. Especially important is the convenient and cheap replaceability of

Jan 1, 1894

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By R. L. Templin

In treating a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum. Factors That Must Be Considered Simultaneously with Cold Working So many other factors affect the physical properties of a metal that it is necessary to consider these factors simultaneously with cold working; their effects vary in magnitude with the amount of cold work present. The most important of these factors are: (I) chemical composition, (2) structure, (3) temperature of working, (4) character of working, (5) rate of working, and (6) methods used for measuring results. For

Jan 1, 1930

By Hans Rumpf

INTRODUCTION Agglomeration is based on adhesion between particles. Production of agglomerates of specific strength, strain properties, size, porosity and structure necessitates the activation of the adhesive forces. To achieve this, it is important for us to know details of the various systems of adhesion. Reports on the work of our Institute for the investigation of systems of adhesion were published on various occasions. A reference to those publications is made in the following abstract, and the findings previously published are presented only to the extent necessary for a better understanding of more recent test results, or of changed ideas. 1. MECHANISMS OF ADHESION We must distinguish between various "mechanisms of adhesion". By "mechanism of adhesion" we understand the interaction between a particle and a substrate resulting from a clearly definable physical or physico-chemical process resulting in a definite mathematical interrelation- ship between the decisive variables.

Jan 1, 1977

By Walter Renton Ingalls

Vague references to tin-deposits in Mexico are scattered throughout technical literature, and that country has been looked to as a likely source of a part of the world's supply of till at no very distant date; but thus far nothing but occasional small lots have come forward, so that the notion has arisen that these mines are either mythical or unworkable. So far as I am aware, there has not yet been published any description of the tin-deposits of Mexico except a few brief references; and this paper, based on a study of them made in 1892, is therefore offered.

Jan 1, 1896

By Walter Harvey Weed

AMONG the many causes of that perplexing feature of mine-exploitation, the unequal distribution of the ore, the influence of the country-rock upon the vein-contents has long been accepted as an important factor in certain districts, but the general application of the theory has not been proved. It is now possible to obtain trustworthy data with which to test the theory, and either to confirm or to overthrow this time-honored tradition. By the searching methods of modern petrography and chemistry, rock-determinations are now scientifically made, while the examination of thin sections of ores supplements field- and laboratory-study, and affords conclusive evidence of the paragenesis of the ore-minerals. In the great mass of data regarding mineral deposits accumulated during the past century, there are some facts which stand the test as to reliability; but the greater part are not available for use in this discussion. Within the last 20 years, however, many able workers have contributed careful and accurate accounts of various ore-deposits; and it is by the facts given in such papers, and by personal experience, that. I have become convinced that there is in some districts a true relation between the country-rock and the mineral contents of the veins. My own interest in the subject arose from the observation of a number of striking instances of the variation of vein-contents with the nature of the inclosing rock. Having already recorded certain observations of this kind, I venture to present in this paper further notes, together with a few facts from the literature of the subject, which seem to prove the correctness of my view. It is apparent that if the relation holds true, though in limited districts only, it will be of great practical in-

Jan 1, 1913

By C. K. Leith

MANGANESE is one of the minerals which is principally consumed in countries other than those of origin. Nearly 85 per cent of the pro-duction is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent of the world production comes from Brazil, Russia, India, the Gold Coast of Africa, and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this movement is for considerable distances and is ocean borne. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metal-lurgical methods, only 35 per cent of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explora-tions now under way, indicate no shortage from a world standpoint for many decades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel in-dustry uses over 90 per cent of all the manganese mined, and is acquiring control of a considerable part of the production in all of the principal fields-the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies are of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing un-easiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few enough to warrant the belief that more or less monopolistic ele-ments of control are not impossible.

Jan 5, 1927

By A. R. T. Denues

LIQUID-OXYGEN explosives commonly consist of a carbonaceous absorbent enclosed in a canvas wrapper and soaked with a liquid containing more than 90 mol per cent of oxygen. Investigation of these explosives in this country was initiated in 1917 by George S. Rice, then Chief Mining Engineer of the Bureau of Mines. The early development is summarized in two papers.1,2 Their characteristics, advantages and disadvantages were considered in a recent bulletin of the Bureau of Mines.,3 Other publications of this Bureau4, 5 treat the technology of these explosives and contain adequate references to pertinent literature. These investigations defined the properties of liquid-oxygen explosives and improved them greatly; however, an outstanding disadvantage is their high inflammability, a property of critical practical importance. These explosives as hitherto prepared are easily inflamed; the combustion resulting from an accidental ignition is particularly dangerous because of the ease with which it passes into detonation. For this reason the Bureau of Mines undertook a cooperative investigation, which has resulted in the development of fire-retardant treatment for the minimization or elimination of this hazard without materially impairing the explosive properties, including the ease of detonation. This presentation will offer a general description of the investigation and the outstanding results. Further phases will appear in subsequent short papers, and the entire investigation including the results of detailed experiments will be available in a forthcoming bulletin of the Bureau of Mines (Bull. 429). The effects produced by fire-retardant treatments of the carbonaceous absorbent and of the canvas wrappers were investigated separately, and the efficacy of combinations of these treatments with particular reference to the possibility of inflammation and to the development of detonation from inflammation was studied. The experimental explosive was pre¬pared from a granular carbonaceous absorbent and. the results described maybe more or less unique for such a material. An extensive preliminary

Jan 1, 1940

By S. Usui, I. Matsuoka, H. Sasaki, J. Shimoiizaka

Depression of galena by sulfite or chromate ion in xanthate flotation was investigated by means of adsorption measurements, electron diffraction and flotation tests. Flotation of galena was depressed by sulfite ion only when galena had been oxidized; no depression took place with unoxidized clean galena. A similar behavior was found when chromate ion was used as a depressant, with the exception that the chromate ion depressed unoxidized clean galena around neutral pH. Depression was attained with galena on which xanthate still remained in appreciable amounts, indicating that the depression is not due to a decrease in xanthate adsorption. The galena surface produced sparingly soluble films under conditions in which depression of galena took place. These films were identified by electron diffraction as lead sulfite and lead chromate on oxidized galena and as chromic oxide on unoxidized clean galena. These observations in conjunction with contact angle measurements, indicate that the depressing action of sulfite or chromate ion arises primarily from film deposition resulting from the reaction between depressants and the galena surface. The thickness of the film was analyzed by means of electrochemical polarization.

Jan 1, 1976

By Richard McCaffery

CONTENTS PAGE 1. Research on Blast-furnace Slags (A Progress Report). By Richard S. McCaffery 5 2. Determination of Viscosity of Iron Blast-furnace Slags. By Richard S. McCaffery, Clarence H. Lorig, Ira N. Goff, Joseph F. Oesterle and Oscar O. Fritsche 27 3. Effect of Magnesia on Slag Viscosity. By Richard S. McCaffery, Joseph F. Oesterle and Oscar O. Fritsche 55

Jan 1, 1931