Search Documents

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

Project Schedule ?Construction 2005 ?2008 (3 years) ?Operations mid 2008 ?2020 (12 years) ?Closure 2020 ?2023 (3 years) ?Post-closure monitoring Victor Economic Facts ?$982 million investment; ?$110 million already invested in the Project; ?1100 person years of employment in construction; ?375 full time positions during operations;

May 1, 2006

By D. Kachongo, Y. Cheng, A. Kashala, D. Samal, G. Mitshabu

Many copper processing flowsheets in the Democratic Republic of Congo include the leaching of oxide ores containing copper and cobalt, copper solvent extraction, copper electrowinning, and precipitation of cobalt salt. Recently, cobalt price gained momentum, driven mostly by the fast-growing electric vehicles battery market. The ore blending scenarios tend to prioritise high cobalt grade ore, whatever the content of copper and other impurities. Therefore, many copper solvent extraction circuits are running below design capacity. The variability of feed induces a variability of the leach solution with respect to copper, manganese, and silica contents. It is thus important to adjust hydrodynamic and metallurgical parameters of the solvent extraction plant to optimise metallurgical performance, production cost, and the quality of the copper electrolyte. This paper presents some results on how solvent extraction plant parameters have been managed in two solvent extraction plants running with lower than designed copper input. INTRODUCTION Referring to a report of the chamber of commerce of the Democratic Republic of Congo (DRC) the online publication Agence Ecofin (2019) indicated that the DRC ranks in the fifth position of the world top copper producing countries with over 1.2 million tons produced in 2018. The same year, 66% of the world’s cobalt was produced in the DRC at over 106,000 tons. If the political situation remained stable and the new tax regime introduced in 2018 did not deter private investors, copper production could reach 1.4 million tons/a in 2020 as pointed out in Mining.com (2019). Forecast figures for DRC cobalt production vary widely depending on analysts. The DRC online magazine Actualité.cd (2018) referring to a ministerial source forecasts over 141,000 t cobalt/a for 2020. The reality will depend on many factors, including the selling price, the supply compared to the demand, and finally the reaction of investors to the new DRC tax regime. The growing electric vehicle batteries market has been the major key driver of the price of cobalt. The five years historical cobalt price graph in figure 1 from infomine.com (2019) shows that the price of cobalt peaked at over 40 USD/lb in the first quarter of 2018. Cited by the online Magazine Creamer Media, Smith (2019) has indicated that the long-term demand of cobalt will likely remain strong.

Jan 1, 2019

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By Sune Eriksson, Stig Peterssonsune, Christer Fridfeldt

"Boliden Metal Corporation has developed a technique to treat complex copper concentrates containing large amounts of lead, zinc, arsenic, antimony and bismuth which cannot be treated in conventional smelters due to the impurities.Tests were carried out to treat such complex copper concentrates in the TBRC. They were performed in a pilot-plant TBRC with charges of 5 tons. These tests resulted in a new method to treat complex copper raw materials and produce a blister copper low in impurities. The background and data from the test work are presented as well as a flowsheet for a full-scale process.IntroductionThe Ronnskar Works is situated on the coast of the Gulf of Bothnia, 40 miles east of the Boliden Mine. Smelting began at Ronnskar in 1930 to process the complex ore extracted from the Boliden Mine. The Ronnskar Works has subsequently developed into a relatively integrated smelting plant.Copper and lead sulphide concentrates from Boliden's own mines as well as purchased copper raw materials are processed. The main products are refined copper and lead, but full utilization of the raw material also yields other metals and some metallurgical and chemical by-products. The products include gold, silver, zinc clinker, white arsenic, arsenic salts and arsenic metal , selenium and selenium compounds, nickel sulphates, sulphuric acid and liquid sulphur dioxide."

Jan 1, 1981

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By J. Sliwinski, J. Oliveira

"The application of geometallurgy and corresponding sample selection can take on several formats within industry. Current practice can range from a strictly geostatistical approach to one in which geological and metallurgical parameters are used in combination to create a representative sample selection strategy. The stage of a project and the level of information available at the time of sampling influences the methodology used to create a representative sample.A geometallurgical study of Carpathian Gold’s Rovina Valley Project in Romania is used to demonstrate a sample selection strategy that integrates geological, mineralogical and metallurgical data to maximize the relevance of the geometallurgical unit definitions. This approach, practiced by Xstrata Process Support for its’ clients, ensures that the results of the metallurgical program can be interpreted in the context of these units.INTRODUCTIONGeometallurgy is a cross disciplinary approach in which metallurgical performance of an ore is linked to intrinsic geological and mineralogical characteristics. The objective of a geometallurgical study is to characterize the range of metallurgical performance of an orebody. This allows the geoscientist or metallurgist to create a robust flowsheet able to treat the full range in variability and to develop production strategies to maximize financial performance. The standard approach is to individually sample and test a series of ore types or geometallurgical units. Several different approaches are used in industry to define what constitutes geometallurgical units and how to sample them.One current methodology is the use of multivariate statistics. Geochemical data along with available geological data are used to define multiple variability domains (Williams, 2004; Walters, 2009). There are risks associated with this methodology since the extent of the data set itself may not support a purely statistical approach at the time that metallurgical units need to be defined. The assay suite collected by exploration programs is often limited to pay metals while metallurgical performance is often affected by ore gangue components. Furthermore, in many cases metallurgical scoping and pre-feasibility studies take place prior to the availability of extensive geochemical data sets. Purely statistical methods can produce multiple populations which require extensive sampling, testing and validation prior to consolidation into a reasonable number of composites for metallurgical testing. Methodologies are therefore required that allow representative sampling and testing of consolidated geometallurgical composites to occur at various phases throughout the development of a mining project."

Jan 1, 2013

By A. H. A. Robinson

Until quite recently-practically up to the present time-all but an insignificant amount of the copper produced in Canada was shipped abroad in the form of ore, matte, blister, etc., there to undergo the further treatment necessary to bring it to the refined state in which it is required by fabricators of copper. Consequently, Canadian manufacturers were forced to import nearly all the copper required in their business; and a considerable portion of the ultimate value to be derived from a Canadian raw material was lost to the country of its origin. In the early days of Canadian copper mining, when both the production and consumption of copper in Canada were much smaller than now, such a condition of affairs was perhaps economically unavoidable, and, in any case, was not a matte~ of sufficient importance to attract general attention. Later on, however, when there had been large and rapid increases both in the production and consumption of copper in Canada, it formed the basis of much adverse criticism, deserved or not, of producers of Canadian copper-criticism that became intensified during the war and subsequent years. Happily, the chief grounds of complaint have now been removed, and there are today copper refineries in Canada, either operating or under construction, that are capable, in the aggregate, of turning out amounts of refined copper greatly in excess of any indicated Canadian consumption.

Jan 1, 1931

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By M. Kane, B. Bissonnette, D. Hodouin

"A laboratory cell has been designed for a careful investigation of gold ore cyanidation using mathematical modelling of the process kinetics. The cell is a stirred vessel with continuous monitoring and control of pH, oxygen and free cyanide contents. Samples are automatically extracted for gold analysis. The instruments are connected to a microcomputer which records all the measured variables and calculates the reagent consumption (air or oxygen, cyanide, lime). For cyanide control a sample is automatically extracted and filtered and the solution analyzed, using a specific electrode, by a flow injection technique. The rate of gold dissolution is modelled using a kinetic model the parameters of which are calculated by a non linear least-squares technique. The parameters of an empirical model of reagent consumption are also estimated. The resulting model is used in a simulator for gold cyanidation plant design, tuning and control.INTRODUCTIONThe leaching of gold ores in a cyanide solution is the usual method for gold extraction from raw ores. This process requires long reaction times and leads to very significant consumption of cyanide. The optimization of the cyanidation plant operation is a very important aspect of gold ore processing for increasing gold recovery and decreasing operating costs. The key parameters to the improvement of gold extraction are the selection of an efficient solution chemistry, the design of the size and the arrangement of the equipment and the correct tuning of the operating variables. Automatic control strategies can then be applied to maintain industrial operations at their optimum setpoints.Two approaches can be used for optimizing design and control of cyanidation circuits, either empirical trials for improving process performances or mathematical modelling of the process kinetics for subsequent analysis, simulation and optimization. The advantages of the second approach, which is used in this study, is that it gives a systematic pattern to interpret data and reliable tools, in as much as the models are good, to improve operation performances. In order to determine the structure and the coefficients of cyanidation models, well controlled measurement and calibration procedures must be used. The purpose of the paper is to present an equipment and a test procedure for modelling the kinetics of gold ore cyanidation."

Jan 1, 1990

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By Thorndycraftm R. B.

"PURPOSEThe purpose of this presentation to the Canadian Mineral Processors is to review gold heap leaching systems currently in use and discuss their applicability to Canadian ores. The author's experience with the development and operation of heap leaching spans the past four years at. Pinson, and visits to many ether heap leaches in the western United States.INTRODUCTIONBy way of introduction to the heap leaching system, I will describe in slight detail the method used at Pinson Mining in northern Nevada. This will be followed by a discussion of optional methods in use at other operations visited.The Pinson orebody is a finely disseminated, well-oxidized hydrothermal deposit. Gold particles are finer than 20- microns. The orezone hostrocks are metamorphosed and silici¬fied limestone and shale. Sulfides and carbonaceous materials are negligible.The Pinson open-pit mine has operated since June 1980. It produces 1500 tpd of C.I.P. mill feed averaging .10 oz gold per ton, and 1500 tpd of heap leach material averaging .025 oz gold per ton. Cutoff grades are 0.04 for mill feed, and 0.01 for heap leaching. Stripping ratio is 9 tons of waste and leach grade to 1 ton of mill feed.The project is located in northern Nevada at 4900 feet above sea level.,Winters are fairly severe, with freezing conditions affecting operations from early December through April. Although officially designated as ""high-mountain desert"" country, snow and/or freezing rain occur almost every week of the winter.To date, all Pinson production-scale heap leaching has treated run-90,000 tons of ore are stacked on 300 foot square clay leach pads. Cyanide leach solution is applied through ""wobbler"" sprinklers at .0025 gpm/sq ft for 60 to 90 days. The pregnant solution flows from the heap by gravity to plastic-lined ditches, into a collection sump and then through buried piping to the 2.2 million gallon pregnant solution pond."

Jan 1, 1984

By Christoph Müller

Information exchange for mine process optimization is essential. Today, modern mining equipment uses the IREDES standard to exchange production plans and reports for easy management and storage. To gain further benefits from process optimization, a mine wide access to real-time information is needed as e.g.: The current status of a machine, operational details etc. Presently, real-time data exchange systems are developed by machine producers. Each machine producer uses its own way of gathering, managing, and storing production data. These proprietary mining processes increase the complexity of cross platform data exchange and management for mines which involves machines produced by different vendors. Casting and unifying the data requires much effort. For this purpose, ?IREDES On-line? currently is being introduced. The standard defines an open, web based method for the exchange of volatile real time machine information. Two different principles are used: Web Services for cross platform information exchange within the IT world and the optional OPC UA for use with automation and process control systems. With such a standard information from machines of different vendors may be managed by using one common platform without spending the effort for dedicated interface development. Additionally, information management and storage will become straight forward since all the data are of the same format. The IREDES On-line standard utilizes the latest IT technologies as well as the knowledge and experiences gained from the previous IREDES standard. The paper explains the benefits, the use, as well as the technical design of the standard and gives application examples from the practice.

Oct 1, 2009

By P. W. Godbehere, B. W. Brooks

"This paper deals with the milling of slags from the Noranda Continuous Process, in the Horne Concentrator at Noranda, Quebec. The milling of copper slags, although novel in Canada, has been practiced in Japan, Finland and elsewhere for several years.In March 1973, the prototype Noranda Continuous Process furnace or ""reactor'' came on-stream, In this pyrometallurgical process (see Fig. 1), copper concentrates mixed with flux are smelted in a single furnace to form copper or a high grade copper matte, and slag. The conventional smelting processes of roasting, reverberatory smelting and converting have been incorporated in a single 17 ft. diameter by 70 ft. long steel cylindrical vessel (l, 2). The copper or matte is tapped from the bottom of the reactor into ladles and transferred to an anode furnace or to a converter. The slag is tapped into 40 ton capacity ladles, cooled, crushed, and conveyed to the concentrator. At the present time, the reactor is operated to produce matte. The matte slag* containing 4 - 6 per cent copper is milled using conventional ore dressing grinding and flotation equipment. A flotation concentrate assaying 35 - 40 per cent copper is recycled to the reactor. Crushing, conveying, grinding, flotation and tailing disposal equipment previously used for over 40 years for ore treatment has been modified to suit the requirements of slag milling. Slag milling is essentially the scavenger circuit of a pyrometallurgical process."

Jan 1, 1977

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By X. S. Yuan

With the production increase of Oil Sand in Fort McMurray Alberta, more efficient tailings disposal has become a priority for Syncrude Canada Ltd. A lot of work on tailings research and development has been compiled to determine the most effective deposition to increase reclamation options, water re-use and thermal energy recovery. Efficient flocculation of fine oil sand tailings is the key technology for thickening. It was identified that flocculation of fine transition/marine ore tailings using a single flocculant was not effective. The thickener overflow contains 1-4% solids content compared with the target solids content of <0.5% obtained with Estuarine ore. As a result, novel processes for treatment of fine transition/marine ore tailings have been developed at Syncrude Bitumen Production Development since June 2004. While the conventional processes using a single flocculant, a single coagulation, or a coagulant-flocculant combination was ineffective for transition and marine ore tailings, the new processes including Coagulation-Flocculation-Coagulation (CFC), Flocculation-Coagulation (FC) and Flocculation-Coagulation-Flocculation (FCF) were acceptable options. The key components of these technologies consist of the recipe of chemicals and their adding sequence. With these technologies, almost all sub-micron clay minerals are aggregated together and settle as a whole, resulting in a clear supernatant of less than 0.1% solids.

Jan 1, 2006

By Peter Rubie, Toni Kojovic, Fengnian Shi

"Mining companies have recognized that characterization of ore breakage plays an essential role in the design and optimization of comminution circuits.Recently the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed a new breakage model incorporating the effect of particle size, and a new breakage characterization testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions.Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalized validation program using machines designed and manufactured by Russell Mineral Equipment (RME). The first unit was installed and commissioned at the Anglo Platinum laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the validation program in 2008, including Barrick, BHP Billiton, Rio Tinto and Teck Cominco. The results from validation tests at the JKMRC and Anglo Research have shown that the JKRBT generates statistically similar breakage parameters to the traditional Drop Weight Test, but with significant advantages over its predecessor. Application of the JKRBT in geometallurgical testing with the AMIRA P843 GeM project has confirmed the JKRBT device offers a rapid and consistent method for determining the hardness of drill core samples. The JKRBT has the potential to revolutionize ore testing, with applications in laboratory impact breakage characterization of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control and management of comminution circuits since the concept is readily adaptable to on-line ore hardness measurement.INTRODUCTIONMining companies have long recognized that the performance of a comminution machine such as a crusher or an autogenous / semi-autogenous grinding (AG/SAG) mill depends not only on the machine operating conditions, but also on the “hardness” of the feed material to be broken. This recognition has driven significant interest in laboratory particle breakage characterisation and testing. The laboratory breakage characterization tests can be roughly classified in two broad groups based on their primary breakage modes: tumbling and impact/compression. The famous Bond ball/rod mill tests (Bond, 1952 and 1961) represent the typical tumbling test and have become the industry standard for estimating the specific energy (kWh/t) of rod and ball mills. However, as the energy application in the single particle impact tests can be well defined and controlled, the latter have received significant attention in the last 30 years. It was estimated that mining companies worldwide spent over three million US dollars on single particle impact breakage characterization testing in 2006."

Jan 1, 2009