Search Documents

By Denholm W. T, Rankin W. J

The reduction of zinc from lead blast furnace slags using hydrogen was studied at 1300¦C as part of a laboratory investigation of zinc fuming. To perform the experiments, 300 g "spent slag" was melted in a crucible. Hydrogen was then injected into the slag through a lance and fresh blast furnace slag was added regularly in small quantities over a period of 40 minutes. Zinc added in the fresh slag was reduced and the zinc level of the bulk slag attained a steady state value of between 1 and 9% after about 10 minutes, depending on the gas injection rate. Because of the high reactivity of hydrogen, bulk supply of hydrogen to the slag was the rate limiting step at the flow rates used and it is believed that the gas-slag reactions in the system were at equilibrium. A partially/stabilized zirconia cell with a Ni/NiO reference electrode was immersed in the slags during the experiments and the steady/state oxygen potentials of the slags were measured. By using the experimental oxygen potential values and calculated values of the steady state concentrations of zinc in the offgas, the activity of ZnO in the slags was calculated from the Gibbs's free energy change for the reaction:

Jan 1, 1989

Teller Underground Mine was established to extract ore from the Middle Vale Reef located on the eastern flank of Telfer Main Dome.The mine is located below a 150 m deep open pit operation. The ore body is shallow dipping highly structured, and is a main aquifer in quite difficult ground conditions.In respect of these conditions it was determined to access the orebody using an adaptation of coal mining and hard rock mining methods, with support being achieved using a combination of island pillars, rock bolts and timber stalls.The paper will describe these methods in more detail, then discuss the successes and failures of these methods when put into practice. As well, it will detail several factors whose influences were found to be greater than previously expected and stress the importance of good geotechnical advice.

Jan 1, 1993

By N Boughen, P Ashworth, S Johns, C J. Yeats, A Littleboy

The ocean floor, often called the last frontier, is increasingly discussed in terms of its resource potential û from near shore building aggregate and placer deposits to massive sulfide orebodies in the deeper ocean. Consequently there is an increasing incentive to mine the seafloor. But, do we have the social license to explore and mine the seafloor? Does this nascent industry have support amongst the wider community? If not, why not? And what should be done? To answer some of these questions, the Wealth from Oceans National Research Flagship has explored the social viability of an expanded seafloor exploration and mining (SEM) industry inAustralia. The results show that there are significant geological and environmental data gaps and that, in the absence of sufficient information, stakeholder reaction to the prospect of an SEM industry expansion may be reactionary and negative. This uncertainty means that the perception of risk from the industry is variable and often dependent on individual values. The acceptability of an expansion to the SEM industry is currently precarious, in particular due to the high levels of uncertainty regarding the environmental impacts of seafloor activity. While there are existing federal regulatory frameworks and government processes for the licensing of seafloor mineral exploration and extraction, there is little precedent in the application and implementation of these regulations. The future viability of the industry will be highly dependant on AustraliaÆs ability to improve the knowledge-base underpinning its regulatory regime and also to generate open and transparent communication channels between stakeholders. It will also be dependent on the SEM industryÆs ability to communicate an acceptable value proposition to society. This proposition will need to include the relative impacts of terrestrial and marine mining, the alternative potential uses of the ocean and the multi-use conflict that SEM might engender. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The working of alluvial deposits has from all times been a popular form of mining, not only from the simplieity of its operations, but also, in its more primitive stages, from the possibility of carrying it on without large capital, without skilled lahour, expensive plant, long terms of preparatory work, or, in fact, any other requisite than a shovel, a dish, and a stout pair of arms. It is possibly one of the oldest industries, and probably, also, it has been one of the most profitable.In tbe Australian States the happy days of rid alluvial deposits, when gold was to be hltd for the shovelling, are now almost over. The lust for gold has caused almost every corner of the world to be ransacked, and the more easily earned wealth to he exhausted: for the most part there remain now those deposits only which are too poor to be profitably worked by means of the implements and methods of old times. But, though the deposits have become poorer, the keen inventiveness of man has devised means whereby such large quantIties can be treated at a cost so low that he can still make a profit out of them. In this article, out of the many means devised, three only will be referred to-viz., hydraulic sluicing, bucket dredging, and hydraulic dredging. All mining may be divided into three principal operations-1st, the breaking down and conveying of the ground to where it is to be treated for the recovery of the metallic values, 2nd, the treatment of the material for the recovery of those values; and, 3rd) the removal of the worthless material or tailings. In all mining the object is to effect these three processes for the least expenditure of money commensurate with the highest degree of efficiency.

Jan 1, 1907

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

By Doig ID, Phillips HR

As a prelude to studying the sorption desorption and permeability behaviour of coal cores in a triaxial stressing rig using sorb- able gases, the air permeability of typical cores was measured. Lump coal samples were obtained from three gas-troubled collieries in Queensland and New South Wales. These were cored in the laboratory and a simple laboratory permeameter employed which accepted 38 x 40 mm cores in a thick rubber sheath. Air pressure of 500 kPa was applied outside the sheath to provide suitable sealing between the rubber and the coal. Differential driving pressures up to 100 kPa were employed and the air flow measured by displacement of water columns in inverted graduated cylinders. Flow measurements accurate to + 2% could thereby be achieved. Coal lumps were cored both parallel and perpen- dicular to the bedding plane, and were observed prior to measurement for any notable features, in particular for the presence of fissures. Between samples an overall variation of from 100 milliDarcy was found in Appin, Westcliff and Leichhardt coals. Significant variation was observed both from section to section of a core and between regions of a

Jan 1, 1982

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By B, G Strobos, J P. Maree, N Smit

In mining and processing operations where minerals, high in pyrite and low in calcite/dolomite are processed, acid is generated, which needs to be neutralised. Ticor at Empangeni in South Africa (SA) produces rutile (TiO2), leucoxene (TiO2 plus iron compounds), titanium (Ti), zircon (Zi) and ilmenite (TiO2 plus iron compounds). Neutralisation is required in the processing plant where acid is leached into the wash water. This water needs to be treated to a quality suitable for re-use in the metallurgical process or to a higher quality to make it suitable for discharge into the Empangeni sewage system (SA). For re-use the water needs to be neutral and under-saturated with respect to gypsum while for discharge into the sewage system the sulfate concentration needs to be reduced to less than 500 mg/L (as SO4). Acid mine water is generally neutralised with lime. Disadvantages associated with lime are the costs and maintenance of the slaking equipment as well as hazards, associated with handling of the alkali. The cost of powdered limestone (CaCO3) in South Africa, a by-product, is 50 - 60 per cent cheaper than lime. A technology has been developed where limestone is used for neutralisation of acid mine water instead of lime. This development includes: Limestone handling and dosing system. A novel, robust system has been developed where waste CaCO3 from the paper industry is slurried to a constant density. A full-scale plant was constructed to evaluate its performance (Figure 4). The dosing system consists of an inclined slab onto which the limestone is stored and from where it is slurried into a make-up tank. The density of the slurry in the make-up tank is controlled via a loadcell that measures the weight of the tank (operated at constant volume) and activates/deactivates the spray of the recycle slurry onto the slab. Integrated limestone neutralisation/lime treatment process. In this process powdered CaCO3 is used for neutralisation and partial sulfate removal of acid leached from the coal washing plant. The sulfate concentration can be further reduced to below the saturation level of gypsum (ie 1200 mg/L) through gypsum crystallisation by means of lime treatment, resulting in metal precipitation (eg Fe3+ and Al3+). CO2- treatment for CaCO3 precipitation. The pH of the lime treated water can be adjusted to pH levels of 8.5 and lower using CO2. The CO2, generated during limestone neutralisation (Equation 2), can be captured and used in this stage of the process. The first two stages (limestone- and lime neutralisation) of this technology have been implemented on full-scale at Ticor to treat the effluent of the process. The constructed plant is 80 m3/hr and differs from coal processing plants by way of not containing Fe(II) and Fe(III) in the water. The CO2-treatment stage (Stage 3) will soon be implemented at IHM as part of a program to optimise the technology for maximum benefits.

Jan 1, 2003

By J Rowland, B Belle, M Webber

The Australian underground coal industry has experienced substantial improvements in longwall productivity and, as such, the methods of providing a safe and productive mine environment have needed to evolve and develop. Whilst the primary method of controlling atmospheric conditions is by airflow it has become impracticable or impossible for the majority of Australian longwall mines to contend with all environmental hazards with primary ventilation alone.If the ventilation circuit cannot provide a safe and productive mine environment at an acceptable cost and circuit duty then supplementary controls are required. Examples include pre-gas drainage, post-gas drainage, gas utilisation, refrigeration and innovative dust control systems. Of the 21 longwall operations surveyed in Australia, there were 13 in New South Wales and eight in Queensland.This study represents a timely opportunity for the industry to examine the primary and supplementary ventilation systems implemented in Australian longwall mines and to discuss how to equip the industry to successfully face the future of underground longwall ventilation management in Australia.CITATION:Webber, M, Belle, B and Rowland, J, 2017. Australian longwall ventilation systems, in Proceedings Australian Mine Vent Conference 2017, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Wang S

Fragmentation is the basic concern in rock blasting and serves as the main measure of blasting effectiveness. A good estimation of fragment size distribution before blasting is very useful and helpful for selecting the proper equipment for loading, transporting, and crushing rocks. A fragmentation model is presented that is based on a hole by hole analysis and correlates the rock properties, burden, spacing, and explosive column with the blasted volume and fragmentation obtained. The drill bench is divided into three separate areas corresponding to different breakage mechanisms. They are: 1) a main breakage or casting area, 2) a secondary breaking area, and 3) an overbreak area. The boundary of the main breakage area is found from the magnitudes of strains in the stress waves and the tensile strength of the rock. The secondary breaking area is determined by stress wave reflections at discontinuities and interactions between colliding stress waves from adjacent boreholes. The overbreak area is that beyond the main breakage area "where the reflected tensile waves no longer break the rock. This analysis is applied on a hole by hole basis to locate the breaking points. Then connecting the breaking points on each side of a borehole forms the triangle of the main breakage area. This is repeated for the next hole and the remaining area is the secondary breakage area. After the angle and area for each hole are found the Kuz-Ram model is used to predict the fragmentation size distribution for each hole. Then summing up the size distribution for each hole gives the total fragmentation distribution. This analysis has been successfully applied to field tests performed in a limestone bench where the entire spoil pile was screened to determine the fragment size distribution. Knowing the explosive and rock properties the breaking area was found for each hole, the strain and stress values, the breaking point, and angle of breakage (104 degrees). The fragmentation size distribution was then calculated and compared to the field data with excellent agreement.

Jan 1, 1990

By D J Rawlings

The Palaeo- to Mesoproterozoic McArthur Basin contains a thick (-10 km) intracratonic platform cover sequence of unmetamorphosed and relatively undeformed sedimentary and volcanic rocks (Pietsch et al, 1991). It covers an area exceeding 180 000 km2 of the North Australian Craton (Figure 1), overlying segments of the older deformed basement and transitional igneous units. Volcanism in the basin (including transitional domain) followed a four-phase pattern. These phases are geologically distinct and widely distributed, and are also recognised beyond the McArthur Basin in many similar-aged tectonic provinces in northern Australia. The four phases are described briefly below. Regional and structural nomenclature used refers to Figure 1. A stratigraphic correlation diagram is presented in Figure 2.

Jan 1, 1994

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

By Braes J. R, Neale J. R

The New Broken Hill Consolidated Limited (NBHC) mine currently produces 1.42 million tonnes of silver, lead and zinc ore annually. All of this ore is treated by the NBHC milling ccx[plex. This paper describes the crushing, grinding, flotation and filtration circuits used in the treatment of this ore and lists the major items of equignent used in these circuits. Metallurgical results, manning levels and consumption rates of reagents and grinding media are shown.

Jan 1, 1983

By P McCarthy

Many mining operations developed in the last 15 years have not performed to expectations. Problems experienced include lower than planned development and production rates, geotechnical/stability problems, unplanned dilution, reduced metallurgical performance and unbudgeted capital/operating costs. Most of these problems can be directly attributed to decisions made on the basis of geoscience interpretations and estimates. Recent case studies continue to provide examples of unplanned events linked to the use of geoscience information. These studies illustrate the need to improve the way geological information is used in mine feasibility and operations. Comprehensive assessment of the consequences of inappropriate technical decision making is still rare; however, the information that is reported highlights the significant financial impact on a companyÆs bottom line.

Jan 1, 2006

By Marsham B, Baker D. C

The expansion of New Broken Hill Consolidated Limited (NBHC) concentrator necessitated the installation of hydrocyclone classifiers where rake classifiers had previously been used. Commissioning of the circuit and optimisation of circuit performance has highlighted problems related to classification of sulphide minerals. Testwork initiated to solve these problems has been used to develop cyclone models which have been incorporated in a ccnputer control strategy for the grinding circuit as a whole. The modifications to the circuit during the commissioning phase and the control philosophy are outlined.

Jan 1, 1983

By Jingmin Xin, Wenhua Xing, Zongxin Huo, Hongzhang Chen

Drawing up the successive plan for mining and development is a very important and regular plan work. The expert system of the successive plan for mining and development drawn up by computer is developed on the basis of network, computer simula

Jan 1, 1998

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By Fulton E, Ring RJ, Waters DJ

The Nabarlek uranium treatment plant of Queensland Mines Limited (QML) is currently treating 600,000 tonnes of ore which was mined and stockpiled in a single four month period prior to commissioning of the plant. During the mining phase, material from the open pit was sorted into ore,'below ore grade uranium material (bogum) and waste using a truck discriminator (radiometric analyser) developed by Australian Mineral Development Laboratories (AMDEL). Ore was stockpiled in a single heap with the location and grade of each truck load being recorded. Bogum and waste were stored separately. From the information recorded, both computer and physical models of the stockpile were constructed. These models are currently used in the planning of day to day reclamation of ore from the stockpile.

Jan 1, 1984

The Savage River Mines concentrator and pipeline has operated for seven years. During this time some problems of general interest have been overcome, particularly in the area of autogenous grinding in large mills and in pump- ing solids over long distances. The plant flow sheet and equipment at Savage River and the control techniques are. described. Ore type has varied widely over the per- iod of plant operation. Techniques developed to minimise the effect of variations on through- put are discussed'. The main technique is the controlled rejection or addition of grinding Media.

Jan 1, 1975

By Lightfoot BW, Foo KA, Conochie DS

Aberfoyle Limited operated a matte fuming pilot plant, incorporating a SIROSMELT furnace in 1980/81. This plant was a significant advance in both smelting and tin extraction technology. Important design, construction and commissioning aspects are discussed and some of the key points to emerge from this phase of the work are reviewed.

Jan 1, 1984