Search Documents

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

Innovative and Resource-Preserving Washing Processes for Primary and Secondary Raw Materials

Sep 13, 2010

This article takes the OMRON C200HE PLC for example introducing its application in mica-paper production equipment, including style selection, address assignment of I/O point, and programming for different function. In the transformation process of simulated data and digit data, the corresponding relations between two data and so on are also discussed.

Jan 1, 2014

By Robert Hopler

In issuing this pamphlet on stump and boulder blasting for the use of farmers, we wish to call attention to the fact that Du Pont High Explosives have been used with universal satisfaction for many years under diverse conditions, and have never failed to give satisfaction in mining, quarrying, roadmaking, blasting stumps and boulders, or for any other work where regard to economy and safety in use is the object.

Jan 1, 2008

By D. Dimitriadis, T. Polglase, W. Phillips, R. Jenny, M. Botz

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfur-containing solids which react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side-reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects which involve the processing of sulfide ores or concentrates or which utilize a biological sulfur oxidation process, more attention has been focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several technologies available to recover cyanide from thiocyanate to both reduce tailings toxicity and allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of technologies available for recovering cyanide from thiocyanate along with estimated operating costs for the technologies. Pilot testing data suggests that in some cases, cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2000

By Emmanuel Henry

Few industries are more challenged by technical, political and market uncertainty than the mineral industry. Technical uncertainty in mining projects concerns the volume and quality of the resource, the processing and metallurgical parameters, the production efficiency, etc. Political uncertainty can take diverse forms and includes possibilities of change in the taxation system, risk of expropriation and risk of social instability or war. Market uncertainty depends on the market structure of the commodity; price and demand volatilities are the most common sources of market uncertainty. Intensive feasibility studies including these uncertainties and risks are required before investing up to billions of dollars in the development of a new mine. Current feasibility studies are often based on a single (or very few) mean geological scenario and simplified price profiles along the life of the project. Yet, strategic decisions, for example, the level of investment in exploration and metallurgical studies, adoption of a flexible, but more costly, mine design and risk-sharing strategies are made at an early stage. Over the last twenty years, Real Option theory has emerged as a unifying framework enabling strategic planning under uncertainty (technical, political and market). Geological and market variances (second order statistics) are pivotal for proper uncertainty quantification. The present study explores the possible benefits of combining modern geostatistical tools and financial techniques for project management. More precisely, the following questions are examined: Is geological uncertainty really an issue? Can we combine geological and price uncertainties in a unifying Real Option framework? A simple example aimed at illustrating the concepts involved is presented.

May 1, 2003

By K. E. Barnes

"The IsaMill was developed for fine-grained ores that required at least double the grinding efficiency of ball or tower milling to be economic. This was achieved, but in practice, the benefits of using inert media (eg sand, slag, ore, ceramic) have proven to be at least as important as the higher grinding efficiency. Flotation selectivity and rate was improved for all particles, particularly fines. This allowed a dramatic simplification of the Mount Isa lead zinc flotation circuit – adding 6 MW of ultrafine grinding power reduced reagent addition and flotation volume and increased plant energy efficiency. This was quite unexpected.This paper examines four orebodies that were enabled by inert grinding – McArthur River, George Fisher and Black Star Open Cut Mines (complex fine-grained lead zinc orebodies in Australia), and the Western Limb Tailings Retreatment plant (a PGM operation in South Africa). In a unique case history, the operating performance of the Mt Isa lead zinc concentrator is explained by size-by-size mineralogical data collected over 25 years, systematically explaining the impact of declining ore quality, and the effects of additional conventional grinding, inert grinding, and circuit and reagent redesign.The mineralogical case histories are so compelling that it is argued that the advantages of inert grinding should not be confined to difficult, fine-grained orebodies. The availability of largescale efficient inert grinding mills could have profound impact on circuit design for many orebodies.INTRODUCTIONThe IsaMill was developed by MIM (now Xstrata) to enable the development of the McArthur River Orebody in the Northern Territory of Australia. This ultra-fine grained ore needed a grind size of 80% passing 7 microns to produce a saleable concentrate. Such a fine grind was not economic with conventional ball or tower milling. Below about 25 microns the low energy efficiency and high media consumption of these mills is prohibitive. Critically, the high steel consumption and associated change in pulp and surface chemistry also seriously affects flotation metallurgy."

Jan 1, 2006

By M. S. Delibalta, S. Kahraman, R. Comakli

The block cutting machine is one of the most important noise sources in the stone processing factories. In this study, the assessability of the noise from the block cutting machines in the stone processing factories using the P-wave velocity was investigated. The noise levels of some block cutting machines were firstly measured during the cutting of the three different rocks. Then, core samples of the same rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. A conversion factor was obtained by dividing the site noise levels by the laboratory noise levels. Then, thirty seven different rocks were cut by an automatic cutting machine in the laboratory and noise levels were measured. The P-wave velocity of rock samples were also measured in the laboratory. A strong relation between the laboratory noise levels and the P-wave velocity was found. The noise level from the block cutting machines can be assessed using the derived relation and the conversion factor.

Jan 1, 2011

Oil sands processing generates huge volumes of slurry, known as tailings, that is being stored in tailings ponds. The volume of produced tailings is a very important factor in oil sands surface mine planning, because the available area for dam construction is limited to the lease areas. On the other hand, oil sands operators cannot leave mine sites without reclaiming the tailings ponds. Since most of the reclamation material is generated in either oil sands mining or processing, it is reasonable to include reclamation material requirement as part of long-term mine planning. In this paper, an integrated optimization framework is proposed to maximize the net present value (NPV) of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. A sample bitumen processing flow sheet is used to formulate the volume of produced tailings, based on Clark hot water extraction method. To verify the proposed model, it is coded in Matlab and run using CPLEX. Run results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Feb 27, 2013

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003

By Hyung-woo Kim, Sup Hong, Sung-Soo Kim, Chang-Ho Lee

A deep-seabed integrated mining system, which consists of four subsystems such as riser pipe, buffer, flexible riser, and tracked vehicles, is presented in Figure 1. In order to collect more manganese nodules, multiple tracked vehicle systems should be used in a deep-seabed integrated mining system.

Sep 1, 2014

By Dale Preece, C. Mick Lownds

Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control.

Jan 1, 2008

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By A. H. Swart

Rock engineering is concerned with the design of rock structures generated by mining activities. Therefore, rock engineering designs have major implications for the safe recovery of mineral deposits and operating costs. The paper deals with a few challenges facing rock mechanics engineers operating in the hard rock underground mining environment in South Africa. Finally, examples are included, which may assist rock mechanics engineers in providing better designs, which could ultimately lead to further improvement in safety and lower operating costs.

Jan 1, 2005

Who Macraes Mining Company Limited is can be summed up by the following statements: +         We have been New Zealand's largest gold producer for seven years +         We have one of the lowest market capitalisation per reserve ounce of the gold producers in the  Australian Gold Index +         We have a resource finding cost of less than NZ$l0 per ounce +         We have a large land bank with proven reserves +         We have an Operating Cash Margin of approximately NZ$200 per ounce +         We have reduced our Dry Milled Tonne Cost by 34% since 1992   Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +         Increasing reserves +         Increasing cash operating margins +         Increasing production   The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment.   The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955